Search Documents

With the advent of the resources boom in the late 1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large scale Australasian open pit mining generally.

Jan 1, 2002

The efficiency of water sprays in suppressing airborne colliery dust depends on many variable factors. A survey of previous work in this field shows that swirl spray nozzles are the best dust suppressors.Investigations carried out in an experimental dust chamber show that, in spite of limitations to the application of water sprays in underground use, promising dust suppression efficiencies in mechanised mining can be obtained with swirl spray nozzles.INTRODUCTIONA dust hazard has always been associated with coal mining, and the recent growth of mechanisation has resulted in a greater production of fine coal and dust, thus increasing the hazard. A better knowledge and appreciation of the medical aspects and dust explosion factors has led to practices reducing the seriousness of the problem. However, the dust hazard still exists and its control is basically an engineering problem.Dust, as with any atmospheric pollution, may be removed from the, mine by ventilation, which is an indirect method of control. Direct methods, in which the dust is prevented from being produced and from becoming airborne, should be employed where possible. Of these direct methods the most significant is the use of water sprays.THE DUST HAZARDAn appreciation of the physical nature of the more important dust hazards is necessary before considering the removal of the hazard. The main hazards associated with colliery dusts are the health hazard and the explosion hazard. "Dust" comprises solid particles of size minus 20 mesh Tyler (833 microns).

Jan 1, 1964

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By R. Stefanko

The use of strain gauges and compression pads for an underground bolt installation in a central Pennsylvania coal mine revealed that satisfactory anchorage could not be maintained in the shale stratum that constituted the immediate roof. Comprehensive laboratory tests resulted in a new shell designed with an increased area of contact and smaller surface serrations. Retightening of the bolt was also found to be beneficial for maintenance of high load values. Roof bolting in coal mines has progressed very rapidly in the last decade, and today this method of support is in general use. There are many theories concerning the functions of roof bolts, but the importance of beam building is indisputable. Proper tension in the bolts minimizes shearing along bedding planes and creates a thick, competent beam from individually weak layers. Bolting must be accomplished immediately upon exposure of the roof, and bolt tension must be maintained if roof failure is to be prevented. Seams are being mined today with roof bolt support where conventional timbering was not effective.' The widespread use of continuous mining equipment was made possible by roof bolts which permit long supported spans free of obstructions. Since adequate anchorage is the key to successful bolting, better methods for determining the efficiency of anchorage are continually being sought. Attempts have been made to measure bolt loads, thus assessing anchorage efficiency by employing sensing devices between the bolt head and roof. 3-s None of the techniques appears to be very accurate, and all have at least one serious deficiency. The greatest efforts are being directed toward the standardization of the pull test.6" Nevertheless, the author believes that the pull test is only one criterion for establishing the efficiency of anchorage and not necessarily the most important one. The conventional pull test involves the short-term application of forces, whereas the success of roof bolt installations is dependent upon the ability of anchorage to sustain relatively long-term forces. Therefore, it would appear that the time-dependent function of the anchor is the single most important parameter for the success of roof bolting in many types of rocks. UNDERGROUND TESTS Strain gauges and compression pads were employed to measure bolt loads in a central Pennsylvania coal mine.8 Bolting had been employed only sporadically in the shale top since dubious benefits were obtained with this type of support. Table I shows some typical results from this investigation. Anchorage losses were extremely variable among the bolts, but all showed a considerable degree of bleed-off. The tests indicated that anchorage efficiency was extremely low in this type of shale. The results confirmed that bolting under these conditions was practically worthless, and thus a waste of material and labor. Probably even more important, bolting constituted a hazard when reliance was placed upon it for support. Certainly the complete lack of confidence in roof bolting, which was apparent in the mine personnel, was justifiable since the bolts did not accomplish their purpose. PRELIMINARY LABORATORY BOLT TESTS The extreme losses in bolt tension that were detected in underground installations prompted a comprehensive study to assess the causes. However, preliminary studies were first made to determine the combined stresses in a roof bolt and to prove conclusively that the observed bleed-off phenomena were due to anchorage: slippage and not to some other physical manifestation. In all of the ensuing tests

Jan 1, 1962

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By Gerardo Fuentes

Arsenic extraction from Chilean copper concentrates up to nearly 99% was achieved, using hydrothermal reactions. Arsenic appears in nature in more than 200 mineral species, being arsenopyrite (FeAsS), enargite (Cu3AsS4), and tennantite (Cu12As4S13) the most common species. In addition, arsenic is present in a large amount of copper concentrates, produced in northern Chile. Medical statistics show that in northern Chile, the amount of cancer to the lung, skin and bladder are the highest in the country. The latter situation, demonstrates the importance of studying metallurgical processes that do not generate atmospheric pollution. The hydrometallurgical processes such as hydrothermal treatment in autoclave reactors, do not produce gaseous emissions. On the other hand, the arsenic remains in solution from where it can be transformed in scorodite by widely known methods. Previous works about hydrothermal treatment of enargite have shown the feasibility of transforming the enargite of the copper concentrates into chalcocite or mineral species of the chalcocite family such as djurleite, digenite and for this reason enrich the concentrate in copper and pass the arsenic to solution. For this research, two Chilean copper concentrates were used, concentrate 1 with 5.5% arsenic and concentrate 3 with 1.8% arsenic. These concentrates were subjected to a complete chemical and mineralogical characterization. Later these concentrates were carry out to batch tests of hydrothermal treatment. Also, these concentrates were subjected to grinding to have different particle sizes. For the hydrothermal tests, a liter capacity Autoclave Engineer reactor was used. Characteristic of this reactor was the maximum temperature 350°C, 5000 PSI pressure, and 900 rpm agitation speed. Kinetic tests were carried out with the two concentrates maintaining the same solid: liquid relationship, the same agitation velocity and the variables studied were treatment temperature, time of reaction, concentration of copper in the solution and grain size of the concentrates. The conclusions of the study indicated arsenic extraction of the order of 93.98% from the concentrate 1 and arsenic extraction of the order of 98.74% from concentrate 3. After the hydrothermal treatment, the solids and solutions were characterized chemically, by electron microscopy and X ray diffraction. Also the solids were characterized by grainsize through a particle size analyzer (MICROTRAC). Results of batch treatment shows that arsenic can be release almost completely from real copper concentrates using this hydrothermal process and the next stage will be a scale up process in order obtain results for pilot plant design. INTRODUCTION Arsenic is an impurity that appears associated with copper minerals forming enargite, tennantite, tetrahedrite, and that due to the pyrometallurgical treatment either in conversion or roasting furnaces, it goes into the atmosphere together with the sulfur dioxide. A great quantity of literature can be found to eliminate arsenic or try to separate arsenic from copper. The methods used are mainly leaching processes with or without pressure (Padilla, Jerez & Ruiz, 2015) with different reagents like chloride media (Herreros, Fuentes, Quiroz & Viñals, 2003) or chloride media with sulphuric acid (Riveros & Dutrizac, 2008) or sodium hypochlorite (Mihajlovic, Strbac, Zivkovic, Kovacevic & Stehernik, 2007). It is known too that Chile is the first copper producer in the world and a great quantity of its minerals are in the north of the country, in Antofagasta.

Jan 1, 2019

By Damian Connelly

The option to leach iron from low grade copper concentrates could reduce transport costs and significantly improve the saleability of the concentrate. In addition, it reduces smelting costs and can remove undesirable impurities. The trend to produce cleaner and higher grade copper concentrates is very appealing to the smelters. A recent copper project came on line and there were three serious deficiencies which were not identified in the feasibility study. This came as a surprise and resulted in a number of projects to investigate ways of rectifying the problems in the shortest timeframe possible and using minimal new capital. The first serious issued not identified when commissioning was the lower than expected copper recovery, which was 70% compared to a predicted recovery of 80% to 87% in the feasibility study. This required investigating new flotation reagents and incorporating controlled potential sulphidisation. The second serious issue overlooked is the presence of significant amounts of talc minerals (insol) in the ore which are naturally floatable. This leads to lower concentrate grade and attempts to remove the talc resulted in lower copper recovery. Smelters have limits on the amount of talc in concentrate because it produces viscous slags and difficulties for the smelter. It also incurs higher transport costs. The third serious issue not identified in the feasibility study was the high arsenic reporting to the concentrate. Arsenic is a penalty element for smelters and at levels exceeding 0.3% the smelters may reject the concentrate. Arsenic is a problem environmentally for copper smelters and penalties apply when it is high. This paper describes the options for penalty element removal and suitability to incorporate into the modified flowsheet. It also highlights where the geometallurgy was not properly addressed and how these surprises could have been avoided. INTRODUCTION From 1970 to 1985, a copper company undertook metallurgical testwork on the Peruvian project copper ore. The ores were mined underground and treated over many years previously. Various other groups undertook studies and work until Aker Kvaerner undertook a feasibility study in 2006. Three ore composites were tested and grind-recovery relationships were developed. The feasibility study testwork identified that talc was a possible concern and will have an impact on copper concentrate grade. This was to be managed by blending. The current operating reality is that there is so much talc in the ore body it is not possible to blend it out. There was far more emphasis on molybdenum recovery. No mention was made of arsenic issues other than blending. There was a Concentrate Leach Study and a Molybdenum Hydrometallurgical Plant Study but these options did not proceed to a final flowsheet. A Scoping Study in 2006 looked at a Heap Leach project. The heap leaching gave very poor copper recovery on the sulphide ore. Heap Leaching was evaluated and tested for the high talc and high arsenic ore but recoveries were poor. The Aker Kvaerner feasibility study opted for a simple primary crush SAG/ball grind followed by flotation and sale of a concentrate. This is the current flowsheet utilised and the scale of the project is very large based on processing 117,200 tonnes of ore per day. A feasibility study does not guarantee success and the deviations from the feasibility study suggest there is a lot of technical work required to improve the current metallurgical performance.

Jan 1, 2019

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem's severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By L. T. Larson

Nothing in Turkey is simple. Its his¬tory is long and convoluted, its culture fascinating, its metallogeny diverse, and its geology very complex. This article will focus on the geology of western Anatolia and the precious metals poten¬tial of this third of Turkey. Any gold produced by mines in Tur¬key since the early 1900s has been a by-product of the mining for other met¬als, such as copper from the massive sulfide deposits of the Pontics. Archaeological records, however, prove that gold was mined from the Pactolus (present day Gediz) River and refined by Croesus at Sardis in about 550 BC. Other records and legends make it possible that gold was mined before 1200 BC for the Homeric City of Troy (Priams treasure?) about 25 km (15 miles) east of Canakkale at Mad¬endag and Kartaldag. A final legend of antiquity suggesting gold in what is now Turkey relates to King Midas. And, indeed, the city-state belonging to a king of that name has been recognized near the city of Eskise¬hir. More recently, precious metals have been mined at Madendag-Kartaldag in the late 1800s. Arapdag, near Izmir, remains the only "authenticated" epith¬ermal precious metal deposit in Turkey (Mosier et al., 1985). With this spotty record, why the sud¬den interest shown by at least five Euro¬pean-based, three or four US-based, and several other international mining firms and their Turkish subsidiaries? Like other aspects of Turkey, the complete answer is not simple but, reduced to its basics, has three parts. Turkey, relative to many developing nations, has a stable, democratic form of government (although it also has a for¬midable bureaucracy) whose currency exchange rate is premised on the US dollar. New laws promulgated since 1983 have opened the country and welcomed foreign investment. Some have even provided investment incentives. The Mining Law of August 1985 made sweeping reforms of the old land tenure system. This law made it possible for a foreign-based company to have a wholly-owned Turkish subsidiary en¬gaged in mining. Equally important is the belated recognition that western Anatolia, while geologically compli¬cated, is today basically a province Neogene extensional tectonics having many of the geologic attributes of the leading gold producing province of the US - the Basin and the Range. Geologic rationale for precious metals exploration Tectonic/lithologic framework: Alle¬gorically and simplistically, Anatolia during early Neogene (middle Miocene) can be likened to a tube of toothpaste with the cap off. It is squeezed in the vise formed by the Arabian plate mi¬grating north toward the southwest end of a stable Asian platform. The "tube" was compressed. It could not expand to the east because it was sealed by what is now southern Russia and Iran. The filling of the tube escaped to the west, in the direction in which the cap was miss¬ing (Fig. 1). So developed during the middle to late Miocene the western-most struc¬tural province of Anatolia. This was done by a process aptly termed tectonic "escape" by Sengor et al (1985). This province is dominated by exten¬sional tectonics much like the Basin and Range of the western US and has an estimated extension of between 30% and 50%. The most striking manifesta¬tion of this extension is the 10 to 11 major east-west trending grabens (Ge¬diz, Buyuk Mendares, Kocuk Mendares, etc.) and intervening horsts, although a much greater number of smaller, gener¬ally northeast-striking grabens and half

Jan 1, 1989

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By C. W. Carpenter, P. T. Bail, J. E. Bobek

This paper presents the results of model studies made to demonstrate the validity of applying the "basic" waterflooding scaling relationships of Rapoport1 to water-wet reservoirs composed of communicating strata of different permeability. Results demonstrate that these relationships can be validly applied, and also show the combined effect of variables on recovery. This demonstration was needed to confirm that the sizable effects of communicating strata on waterflood behavior, observed in model studies, were actually representative of field behavior. INTRODUCTION Rapoport1 Collins2 and others have presented scaling laws for modeling water-oil displacements. The validity of these laws has been experimentally demonstrated for homogeneous systems only. Recently, however, several investigators have presented the results of multilayer model studies made to determine the effects of viscous, capillary and gravitational forces on oil recovery in systems composed of communicating layers of different permeability. Dyes and Braun,3 using miscible displacements to simulate water flooding, showed that vertical communication adversely affects recovery at unfavorable viscosity ratios in the absence of capillarity. Ogandzhanyants and Egorova, 4 Gaucher and Lindley,5 and Richardson and Perkins6 modeled water-oil displacements in layered systems using immiscible fluids with capillary forces present. These investigators found more efficient behavior than in the miscible system of Dyes and Braun. However, since the scaling laws had not been verified for heterogeneous systems prior to or during these tests, it was necessary to assume that the results were representative of field behavior. This report presents the results of model studies made at Jersey Production Research Co. to find out if the waterflooding scaling relationships are valid when applied to water-oil displacements in heterogeneous reservoirs with vertical communication. Data obtained in the study show the combined effects of viscous, capillary and gravitational forces on oil-recovery behavior. The studies were performed in strongly water-wet systems where strong imbibition forces were present. For systems of different wettability, the effects of capillary imbibition would be somewhat different than those presented. APPROACH The scaling laws studied were those developed by Rapoport1 and designated by him as "basic" scaling laws. These relationships require that the model be scaled to the geometry of the prototype, and that the model and prototype be operated at the same viscosity ratio and have identical relative permeability curves, contact angles and boundary conditions. It is also necessary that the groups** be identical in the two systems, although any of the parameters making up the groups may be different. Finally, the capillary pressure of one system must be directly proportional to that of the second. Studies were conducted in two four-layer models, representing quadrants of five-spots, which were geometrically similar and which had the same glass-bead packing. The fluids used assured the same wettability in both models. Thus, the contact angles and relative permeabilities of comparative sand layers in the two models were identical and the capillary pressures were directly proportional. However, one model had a characteristic length three times that of the other. To make the scaling groups equal and to check the scaling laws, it was necessary to adjust the rate, water-viscosity level, interfacial tension and water-oil density difference to compensate for the difference in model sizes.

By P. E. Baker

Approximate solutions are presented for the heat-flow equations in a loss-free linear system with a moving source and with heat transfer by convection and conduction, representing in situ combustion in an oil reservoir. The rate of heat generation and the velocity vf of the source (flame front) are assumed constant. A cold front or convection front caused by the cooling effect of in-jected air develops behind the flame front and moves with velocity vc, which is determined by the thermal properties of the air and rock. Because of thermal conduction the fronts are not sharp; i.e., they do not represent temperature discontinuities. The following solutions apply after a sufficiently long time. where Q is heat generated per unit volume of formation, k is thermal conductivity, CF is volumetric heat capacity, a is thermal diffusivity, and subscripts 1 and 2 refer to values behind and ahead of the flame front, respectively. The parameter CF2 is contained in v . Te is initial reservoir temper- . C2 e ature and air-injection temperature. Other mathematically possible solutions are presented. The different solutions result from the use of different values for various physical parameters. The solution just presented is thought to be most commonly applicable. INTRODUCTION In this paper, approximate analytical expressions are derived for the temperature profile developed in the underground combustion method of oil recovery. A qualitative description of the process may be found in a paper by Tadema.1 The flame front is regarded as a moving source with a constant rate of heat generation. Heat transfer is by conduction and convection. Previous publications, of which a few are cited here, 2-5 have also attacked this problem and have presented solutions pertaining to different methods of approximating or idealizing the process studied. The present paper also treats an idealized case: linear flow is assumed for heat and fluids, and vaporization and condensation effects are neglected. The results obtained are similar to those derived by Bailey and Larkin,3 but are obtained by an entirely different procedure. The method used here should give considerably greater insight into the physics of the in situ combustion process. Four types of cases are considered, distinguished by thermal and fluid-flow properties of the system. A constant rate of heat generation and constant rate of flame-front advance are assumed. Flame-front temperature is determined for each case using a heat balance which involves the entire temperature profile. The applicability of the different solutions to real systems is discussed after they are all presented. Again, this is done for the purpose of understanding better the physics of the process. Consideration of the nonapplicable solutions and of the reasons for their not applying is significant. In a paper by Cooperman,4 the only case solved is one considered here as not applicable. Fluid flow, as such (pressures, saturations, oil recovery, etc.), is not treated. This subject has been covered in a paper by Wilson, et al.6 Also, we are not concerned with requirements for continuance of the process; we only attempt to determine the temperature history for cases where the process has continued for some time. PHYSICAL SYSTEM AND APPROACH TO PROBLEM A linear flow (heat and fluid) system is assumed and the x-axis is taken parallel to the flow direction. The combustion zone (flame front) is vertical,

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By Anthony R. Przybylek, John M. Visnesky

INTRODUCTION Thermal dryers have been utilized for reducing moisture of bituminous coal since the late 1930's. Since that time, numerous changes in the coal industry have motivated advances in thermal drying technology. The purpose of this paper is to discuss the changes that occurred to dryer design and focus on current practices of fine coal drying. The major topics discussed in this paper are: - Early Thermal Dryer Design and Evolution - Current Drying System Design and Associated Components - Current Economics of Fine Coal Thermal Drying - Future Markets and Design Considerations EARLY THERMAL DRYER DESIGN AND EVOLUTION Background The practice of drying fine coal with heated air has been performed for more than one half century. Throughout that period, both Metallurgical and Steam coal producers have used this method for reducing the surf ace moisture content of their fine plant products. During the late 1930's and early 19401s, vibrating bed and flash dryers were used to per- form the drying duties. Closed water circuits and vacuum filtration had not yet been integrated into process circuitry and centrifugal dryers were in their early stages of development. During that same period, changes in mining practices were reshaping the distribution of coal to our processing facilities. Plants originally designed for the purpose of processing coarser fractions of coal were being burdened with additional quantities of fine coal. Those plants, unable to recover fine coal, would reject these solids to plant bleed. The higher incidences of stream pollution that resulted from these events prompted clean stream legislation and the need for new, more efficient fine coal recovery circuits. The coal processing industry responded to these needs by integrating closed water circuits and filtration into circuits. The fine coal filter cakes recovered exhibited poor handling characteristics by themselves and often required further dewatering to improve their characteristics. Flash dryers at that time were being used to dry the coarser products. For those facilities operating flash dryers, the solution to this new problem appeared to be simple. The filter cake was combined with the coarser (-1/4") coal and then introduced to the flash drying column for drying. The filter cakes, however, presented significant problems for the flash drying systems. Heavy lumps of filter cake could not be dispersed and conveyed by the rising hot air and as a result would settle out in the bottom of the column. This material, known as "drop-out", would then accumulate and require further handling. The solution to this problem was not an easy one. Sophisticated mixing equipment was employed to condition the feed to the dryers. As attempts to minimize drop-out with this approach failed, the only recourse was to collect the material with conveying systems and recycle it back to the plant or dispose of it. The additional costs of handling this material reduced the attractiveness of the flash systems and opened the door for the development of a new, more cost effective coal drying system. Due to the nature of the problems experienced by the flash systems, fluid bed systems were considered. Fluid bed dryers were being used in other industries at that time but had no operating history in the coal industry. Dorr-Oliver transferred technology from other industries and built the first fluid bed drying system for fine coal.

Jan 1, 1988

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By J. Skrove, C. R. Boardman

In situ permeability of the rock outside the Hardhat chimney was determined by pressurization of long holes with air. Experimental data indicated a remarkable difference between fracture permeability of the rock near the chimney and that at a considerable distance. Although permeable fault zones were known to exist in the granite stock, the measurements of background permeability were quite low, on the order of tenths to several millidarcies. The observed difference is about two or three orders of magnitude above this background in the region 125 to 215 ft radially from the shot point, or 80 to 165 ft radially from the vertical axis of the chimney. The presence of a collapsed drift immediately beyond this region precluded measurements which could have defined the maximum extent of the zone of high permeabilily. INTRODUCTION Previous exploration has revealed that contained nu-clear explosions create cavities which generally collapse, resulting in rubble-filled chimneys and annular fractured zones. These geometries have been shown to result in complex flow regimes which should increase the production rate from hydrocarbon reservoirs.' Empirical scaling equations have been developed for estimatina chimney radii and heights for a variet; of rock media.' The exten; of the annular fractured zone has been documented and associated permeability changes have been observed qualitatively for several explosions. This study was begun to establish the nature and magnitude of the permeability of the latter region. It is anticipated that results will be useful in estimating permeability changes and consequent production stimulation which might ensue from a contained explosion in a hydrocarbon reservoir. The post-shot environment of the Hardhat event (a 5-kt contained nuclear explosion in granitic rock) was c'hosen for the experimental measurements. The Hardhat device was detonated at a depth of 939 ft, and subsequent exploration revealed a chimney of broken rock with a radius of 65 to 70 ft and a height above shot point of 281 ft.' BeFore the explosion, the Hardhat medium was highly jointed and fractured (Fig. I). Jt was expected that differential rock motion along these and other weaknesses induced during cavity growth and collapse would significantly alter the permeability of the rock mass. EXPERIMENTAL METHOD Initially, three 2-in. diameter holes (Nos. 10, 12 and 19) were drilled about 25 ft outward through the walls of the 500-ft level drift (elevation 4,253 ft, Fig. 2). One was drilled near the chimney and two holes, one vertical and the other horizontal, were drilled near the shaft. Order-of-magnitude differences in permeability obtained by pressurization measurements indicated further: investigation was warranted. A series of 3-in. diameter holes was then drilled with water as a coolant into the walls and roof of the drift (Fig. 2). An 11-in. long packer was set from 1 to 8 Et inside each hole and air was injected at measured Row rates. Hole pressures were monitored at the collar. Permeability was low enough in the holes near the access shaft that pressure could be maintained long enough to obtain good pressure decay rates. In the vicinity of the chimney, however, permeability was so high that this was not possible and air was injected under steady-state conditions. About one year later, these same holes were retested to

Jan 1, 1967

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and "{2,3,10)" or "(127)". (It is now thought1' that the "{0,1,13)" habit reported for the Fe-Ni-C alloys'' is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove.' The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and tj2 = vi (i = 1, 2, 3), the Kz qd 771 elements are given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics cij Iand cij reduce to the unit tensors 6ij and 6ij so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and 77~ are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By A. Berghezan, E. Bull Simonsen

A simple and general method is described for melting and zone refining refractory metals by induction heating on a specially shaped water-cooled copper crucible. The crucible is the essential part of the apparatus and is placed horizontally. It consists of either a copper plate, or a flattened tube, or of several parallel small diameter tubes all water cooled. The charge lies on the crucible, or whenever possible, is suspended above it. This assembly goes into a transparent quartz tube and the whole is passed through the coil of a radio frequency generator. Vaarious atmospheres can be used. No contamination is detected from the copper crucible. purification is obtained both by selective evaporation of impurities and by zone refining. METHODS of melting and refining relatively large ingots of all reactive and refractory metals as well as some semiconductor materials have been developed in this laboratory during the past several years using induction heating and cold crucibles. These methods are simple and permit the use of a variety of starting materials in preparing ingots of suitable shapes. Among these methods, two are of particular interest. One deals only with the problem of melting without contamination. In this method the induction coil has a specially designed shape and acts simultaneously as heating element and crucible. The second goes one step further, being designed for both melting and further purification of the refractory metals. The aim of this paper is to describe the second method which is of more general interest and of greater applicability to metallurgical problems. A) THE PRINCIPLE OF THE MELTING AND PURIFICATION METHOD As originally proposed by one of us1 the method consists of heating a charge of any refractory metal or semiconductor material to the melting point on a water-cooled copper crucible by passing both the charge and the crucible through the induction coil of a radiofrequency generator. Although both are subjected to the same induction field, one achieves the melting of a refractory metal on a copper crucible even when the refractory metal has a melting point of more than 2000°C above that of the crucible. This seemingly "odd" method works effectively for the following reasons. Because of its high electrical and thermal conductivity as compared with the material being melted, copper can be used as the crucible and kept at a low temperature while the material is heated by induction to its melting point. With water Silver and other highly conducting materials can also be used. If a nonconducting material is contemplated, e.g. SiO or a high polymer, a very thin wall should provide efficient cooling. cooling through ducts in the crucible its temperature can be kept between 40" to 70°C; thus its electrical resistivity is kept low, while the resistivity of the charge increases rapidly as its temperature is increased. B) APPARATUS The crucible is the essential part of the apparatus. It has been designed in various shapes depending on the atmosphere used, whether vacuum or an inert gas or hydrogen. In all crucible designs an effort was made to reduce its volume to "nothing but the cooling water" in order to avoid shielding the ingot from the induction field. In practice it is either a

Jan 1, 1962

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

The microstructural stability of 59 carbon and low alloy steels after 34,000 hr exposure at 900' and 1050°F, including the weld heat-affected zone, is discussed. The tensile and creep rupture properties of the parent metal of many of the steels before and after 10,000 hr exposure are presented. SEAMLESS pipe has been used for many years at elevated temperatures. When seamless first began to be used, operating temperatures and pressures were relatively low and the steel produced adequately met the existing requirements. The need for knowledge of creep properties and graphitiza-tion was nonexistent. Today the requirements for tubular products have changed considerably. Operating temperatures and pressures are increasing continually and corrosion, particularly at high temperatures, presents a problem. Carbon steels have, under these conditions, certain economic advantages particularly in oil refinery use. However, the use of low alloy steels in the generation of steam power has increased appreciably due to the influence of molybdenum on creep strength and the control of graphitization with chromium. The behavior of carbon and certain low alloy steels after long periods of exposure at 900° and 1050°F (480° and 565°C) has been investigated. The steels were examined before and after 10,000 to 34,000 hr exposure. Results obtained with material exposed at 1200°F (650°C) are not presented due to the severe oxidation and resulting decarburiza-tion after long periods of exposure. The graphitization characteristics of carbon and low alloy steels are of fundamental concern to the users of these materials. This is particularly true where welded joints are employed. In order to evaluate properly the behavior of steels at elevated temperatures, it is desirable to employ not only long periods of exposure under controlled conditions, but to use material with known properties and steelmaking practices. The purpose of this investigation has been to study the microstructure of the weld and the tensile and creep rupture properties of the parent metal after long periods of exposure at elevated temperatures. In the report'.' of a previous investigation data were presented on the microstructure, impact strength, hardness, and oxidation characteristics after 10,000 hr exposure at elevated temperatures. When this investigation was planned, methods for controlling the graphitization characteristics of steel were not established and, therefore, a number of special alloy steels were included in the study. During the exposure of these steels, the influence of aluminum in accelerating the rate of graphitization and the inhibiting power of chromium were established by various investigators. Also, the vanadium-bearing steels, because of their outstanding creep properties, received attention. As a result of these developments, considerable progress has been made in the field of high temperature tubular products, and the necessity for special alloys to prevent graph-itization has been restricted largely to the use of chromium. Material Chemical analysis, deoxidation treatment, and austenitic grain size of the 59 steels discussed in this paper are shown in Table I. The steels were forged to 1x1 in. bars with the exception of steels 12B, 12DX, 12DY, 12DZ, 70, 70A, 72 to 78, 82, and 83 which were machined from heavy wall pipe. All bars were surface ground before exposure. Heat treatment before exposure is shown in Table 11. The majority of the steels included were melted in either a basic open hearth or basic electric furnace; how-

Jan 1, 1955