Search Documents

IT IS impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affected. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direct-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followed by other smelting and reduction companies and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silver ores was the principal problem to be solved. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc concentrates. This period includes the world war, when abnormal prices stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. PRODUCTION AND VALUE OF ZINC CONCENTRATES The production of zinc concentrates during 1924 was approximately , 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By J. T. Brown

AS far as could be ascertained, no one had previously investigated the creep strength of silicon poly-crystals. Literature has appeared showing evidence for plastic deformation in silicon single crystals and whiskers.*1"6 Also the fact that germanium, a material of similar crystal structure to silicon undergoes plastic deformation under stress at temperatures above about 60 pct of its melting temperature, has been known for some time.2"4'7 This investigation was performed for the purpose of determining the strength and ductility of silicon polycrystals under creep conditions that would give fairly long times to rupture. PROCEDURE The silicon specimen blanks were obtained by first placing granulated transitor grade silicon (99.999 + pct pure) in a silica crucible. The crucible was surrounded by a graphite susceptor, and induction heating was used for melting the silicon in a vacuum furnace. Blank specimens were formed by freezing molten silicon onto a polycrystalline seed of silicon in a vacuum furnace. The seed was attached to a motor driven revolving rod. As silicon solidified, this rod was gradually withdrawn from the melt. A shape with a contracted center section was obtained by varying the rate of withdrawal from the melt. Specimens for the creep-rupture tests were ground from these "pulled" blanks. Creep-rupture tests were performed in spring loaded machines under constant load at 1800" and 2000° F. RESULTS AND DISCUSSION A test specimen which was sectioned longitudinally is shown in the photomacrograph in Fig. 1. Very little deformation has taken place in the portion of the specimen shown, however, slip lines from several slip systems within the same grain, and deformation band formation was seen. The elongated appearance of the grains is due to the method of growing the specimens. One of the most interesting aspects of the results obtained from the creep-rupture tests was the high strength and the accompanying large amount of ductility. The data obtained is listed in Table I which shows the stress to rupture in 100 hr at 2000°F is between 8000 and 9000 psi. This indicates that silicon's strength at 2000°F is about equal to that of the best commercial super-alloys. It is important to mention that silicon has less than 1/3 the density of iron-, nickel-, and cobalt-base alloys. The usual type alloys for high-temperature applications

Jan 1, 1960

By K. Nassau

The Effect of tin and hydrogen on the C0 parameter of a titanium. specimens were capsule cooled in water to eliminate contamination by water. Deybe-Scherrer photograms were obtained in a 114.6 mm camera with CuKa radiation. The parameters shown in Table I and Fig. 1 were calculated from the 213 (8569°) and 302 (8173.5°) reflections? no attempt being made to correct for systematic errors. The principal difference in method of preparation of specimens between this investigation and that of Worner was the use of pickling by the latter to produce X-ray diffraction samples. The possibility that hydrogen introduced by pickling was responsible for the lower a and c-parameters was investigated with the same 80 pct HNO3- 20 pct HF solutions used by Worner. The 6 and 10 at. pct specimens, the parameters of which had already been determined, were pickled and the c-parameters obtained are also shown in Fig. 1. The a-parameters, not shown, are also diminished. The quality of the lines obtained from the unetched and etched samples was unchanged, being quite sharp in both cases. It is quite possible that if corrections for systematic error carried out that the parameters obtained for the unetched samples would approach the data of Worner. In any event, the parameters of the etched samples would be still lower. The data obtained here is evidence that hydrogen in solution has contracted the c and a -parameters. Crystallographic Angles of Calcium Tung-state (Tetragonal, c/a = 2.169) K. Nassau In connection with the preparation and orientation of single crystals of calcium tungstate (Scheelite -CaWO4), the need arose for a stereographic projection for this tetragonal material. There appear to be no tetragonal projections with a c/a ratio above that of indium1 (c/a = 1.522) in the literature. In addition to its use for calcium tungstate, such a projection might find other more general applications and is accordingly presented below. The most recent X-ray diffraction work on CaWO4 is that of Swanson, Gilfrich, and Cook,2 where a summary of previous work is also found. Lattice parameters given are: a = 5.242A, c = 11.372A, and c/a = 2.169. The material is tetragonal with space group Table I, giving angles between crystallographic planes (HKL) and (hkl), was calculated from the formula3

Jan 1, 1961

By R. B. Newcombe

Despite abnormal economic conditions and the unhealthy state of the petroleum industry, 1930 closed without any marked decline in total production of oil in the Middle Western States. The most accurate figures available would indicate for this district an output of close to 25,000,000 bbl. for 1930 as compared to 26,000,000 bbl. for 1929. This can be accounted for by the settled nature of a great many of the wells producing in this area and the favorable geographical position, which affords adequate refining and marketing facilities. The only new flush production field discovered in the area was the Legrande oil pool in southeastern Hart County in western Kentucky, where wells up to 1000 bbl. initial have been reported from a shallow depth. Important extensions have been found in a number of central Ohio fields, and activity in the central Michigan area resulted in new pools along the northwest trend of the Mt. Pleasant structure. These new districts, known as the Leaton and Vernon pools, have not yet reached the scope of the Mt. Pleasant field proper, and although the structure is similar, sand conditions are not strictly analogous. Wildcatting was retarded somewhat by the scarcity of market for oil and many important wells were shut down for several months. This has not shown such a profound effect on production as the reticence of operators to drill inside proven locations. The major companies have not been able to dispose of their oil and the smaller operating units are having trouble financing their projects. The result is that oil in sight is not being produced and output is suffering accordingly. Another important effect on production was the introduction of proration by the major crude purchasers and a voluntary shut-down by Kentucky operators. This step became necessary because of the glutting of lake port refineries with Mid-Continent oil, and was not fostered by regulating state bodies, as in the case of the southwestern states. Small refining units have sprung up to meet this situation in a number of instances but they have experienced some difficulty in disposing of their product because of "dumping" tactics from other quarters. New refinery outlets on the Great Lakes and new pipe line connections should tend to alleviate this difficulty during the coming year. The

Jan 1, 1931

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.' Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.' The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

Records of coal in Colorado begin only a few years before the Civil War. In 1859 Macomb reported beds of lignite on both sides of Galisteo Creek, and in the foothills of the Placer Mountains, a place where an outburst and overflow-of trap had changed the lignite into bright, hard anthracite.1 The Union Pacific Railroad sent Joseph T. Hodge to investigate the coal deposits in the Rocky Mountains, close to the projected line, in the fall of 1863. He was told of coal on South Boulder and Rock Creeks, and that somewhere on Lodge Pole Creek it was being worked for supplying fuel for stage stations; a bed was also reported seven miles north of the stage road between Laporte and Latham. It was only in the vicinity of Denver that coal mines were being worked to any extent; these openings were on Coal Creek about 22 miles north of the town, said to have been opened in. 1860. The coal was used by the smiths with ,difficulty and slacked badly on exposure., Some coke was made from one of the seams, the coke being preferred to the raw coal by smiths. Another district was opened along South Boulder Creek, about two and a half miles from the base of the Rocky Mountains, two mines being worked to supply the Denver market.2 Hayden reported a large bed of coal at Golden in 1861 and of having seen a similar one in 1862 about 65 miles east of Pikes Peak, and in 1866, he saw large beds on Rock Creek 16 to 19 miles from Golden. In 1867 he saw the Belmont or Marshall's mines opened in 1863 on South Boulder Creek, which he said was the finest exhibition of coal in the state. The next one was the Murphy mine, on Ralston Creek, five miles north of Golden. A mine was also being worked near Canon City at that time.3 The coal at Golden was being worked in 1864.4 In 1867 the coal mined at Golden was being used in a firebrick' works. At Canon City and other places on the waters of Arkansas River, coal was being mined for use in the valley towns, bringing $5.00 per ton at the mines.5

Jan 1, 1942

By W. J. Fene

"The prevalence of accidents in the coal-mining industry has prompted a study of the workmen's compensation laws of the various States and the statistics of accident costs, for the purpose of explaining to operators how the compensation laws are regulated and to show the cost of accidents.The subject of compensation laws and accident costs is by no means new, but the prevalence of coal-mine accidents would indicate that the mine operator in general is not thoroughly conversant with their importance. Unquestionably, compensation laws are a large factor in promoting accident prevention, and it is believed that a greater measure of success would be accomplished in preventing accidents if all mine operators were fully aware of their important bearing on the cost of production.Many operators seem to be indifferent to accident occurrence; possibly they do not real¬ize the seriousness of the accident hazards that exist in their mines, even after the hazards are brought to their attention. There is no question that material financial advantages are to be gained by the prevention of accidents and it would appear that when these advantages are thoroughly understood, operators would be anxious to eliminate, insofar as is feasible, conditions likely to cause accidents.The unsettled state of the mineral industry and the irregular operation of mines during the past several years has probably been an important factor in influencing the apparently indifferent attitude of the operator. The chaotic conditions in the mining industry and especially in coal mining are unquestionably a factor that tends to increase accidents, just as mine idleness increases roof hazards and results in deterioration in mechanical, electrical, and haulage equipment, and promotes disorganization of the personnel. During such times greater efforts should be exerted toward the prevention of accidents because of these increased hazards and of the financial advantages brought about by the various savings to be effected when mine accidents are held to a minimum.This report on accidents in the coal mines of Pennsylvania was made possible largely through the cooperation of William J. Maguire, director, Bureau of Statistics, Pennsylvania Department of Labor and Industry, and Rush N. Hosier, superintendent, Coal Mine Section, Pennsylvania Compensation Rating and Inspection Bureau, who made available their records and extended much assistance and numerous courtesies during this study."

May 1, 1932

By L. C. Morganroth

Discussion of the paper of L. C. MORGANROTH, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 475 to 481. DAVID B. REGER, Morgantown, W. Va.-I notice in the third paragraph of the first page of the paper, that in mentioning the clays of the Pottsville series, the author says: "The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible."). If the author wishes to confine himself to the fire clays of Pennsylvania, as the title seems to indicate, I have nothing to say, but if he wishes to include a discussion on fire clays of the adjoining States which the. subsequent paragraphs of his paper seem to indicate, then I wish to call attention to the fact that there are large and extensive deposits of fire clay in the Allegheny series, immediately overlying the Pottsville in the northern counties of West Virginia. These fire clays have been studied carefully, and described in several reports of the West Virginia Geological Survey, first in the report on Ohio, Brooke, and Hancock Counties, in the northern part of the State; described later ,in the report on Monongalia, Marion, and Taylor Counties, and in the report on Preston County, which followed. In these latter counties (Monongalia, Marion, Taylor, and Preston) there are some beds of fine fire clay, varying in thickness from 6 to 10 or 12 ft., with a content of only 2 or 3 per cent. of fluxing ingredients, and these are of the typical Savage Mountain appearance and also have the typical Savage Mountain fracture. They have been prospected, but not mined a great deal. Several of them have been tested in blast furnaces and furnaces for other purposes, in glass-manufacturing plants, also for firebrick, arid have been found to be very good. They are simply awaiting development, and I merely want to call attention to the fact that there are plenty of them in the Allegheny series still above the Pottsville in West Virginia. There are two or three valuable seams which I have seen in person and have had analyzed in our laboratory.

Jan 5, 1916

By K. Nuttall, S. Vijayan, A. J. Meinyk, R. D. Singh

For conventional applications, there is limited demand for rare earth elements as well as yttrium and scandium. But the emergence of new high technology applications such as supermagnets, lasers, and superconductors should result in significant demand for some of these elements. This article examines the anticipated applications and demands for rare earth elements over the next decade. It also looks at the implications on the use of available resources. In the context of a growing demand, process methods are reviewed for the recovery of rare earth elements from conventional and unconventional resources. And the article also discusses the challenges facing the mining industry in meeting this opportunity. Reserves and reserve base The rare earths (RE) are a homogeneous group of metallic elements occupying the area from lanthanum to lutetium in group IIIB of the periodic table. Yttrium and scandium are also included with the rare earths because of their chemical similarities and common existence in nature. These 17 elements and their atomic numbers are shown in Table 1. The rare earths are widely distributed in low concentrations throughout the earth's crust (Hedrick, 1985). They occur in many rock formations including basalts, granites, shales, and silicate rocks at concentrations of 10 - 300 ug/g. They also occur in more than 160 discrete minerals. Most of these are rare, but may contain as much as 60% rare earth oxides (REO). More than 95% of the REO occurs in three minerals: monazite and bastnasite for the light rare earths and xenotime for yttrium and the heavy rare earths. Apatite and multiple-oxide minerals, such as euxenite and loparite, are also commercial sources of the lanthanides and yt-trium. Rare earths do not occur in nature in the elemental state. And, except for scandium, they do not occur in minerals as individual compounds. Bastnasite and monazite are the two major minerals used commercially to supply most of the rare earths (Hedrick, 1985). Bastnasite is a key raw material source for the cerium subgroup elements. The largest known bastnasite deposit occurs with iron ore minerals in China. The second largest deposit is situated in California. Typical rock analyses of the fluorocarbonate mineral bastnasite deposit in California show about 15% bastnasite. The REO content of that is about 50%. Monazite is present in beach sands in many parts of the world. This includes India, Brazil, Australia, South Africa, the

Jan 1, 1989

By I. S. Servi, N. F. Graves

THE etch-pit technique has long been used to reveal low-angle boundaries and, in general, the distribution of dislocations in high-purity metals. Often this technique is amenable to quantitative computations,' but generally is affected by some degree of uncertainty because etch pits can be nucleated not only by dislocations, but also by inclusions and surface imperfections. In the case of high-purity zinc, Gilman' reported that etch pits were produced only after adding 0.1 atomic per cent of cadmium to the crystals and aging at a proper temperature. In the course of a study of low-angle boundary behavior in zinc crystals, etch pits were produced in 99.999 pct zinc without resorting to intentional contamination, by etching in a 50:50 HNO3H2O solution. The technique consists of etching until the heat of reaction brings the solution to a boil, and in displacing the etchant rapidly with a stream of cold water, thus avoiding staining. The undesirable features of this technique are the heating effect and the removal of a considerable amount of material. A high polish is obtained if staining is controlled properly; therefore, the etch pits appear very clearly and with excellent contrast when observed under dark field illumination. This is especially helpful for cursory examinations at low magnifications. Several observations were made on zinc crystals of square cross section, having one face parallel to the basal plane and one edge parallel to a slip direction, Fig. l(a). When such a crystal was bent about 2" over a glass die and annealed at 390°C, a sharp boundary was formed only in the inner portion of the crystal. Near the two prismatic faces, perpendicular to the basal plane, the boundary was always branched into many lower-angle boundaries, Fig. 1(b). Attempts to move the main boundary by applying a shear stress to the specimen invariably resulted in curving the boundary, the branched ends remaining pinned in their original location, Fig. 1 (c). The prismatic face, when etched as indicated in the foregoing, revealed the existence of numerous (sometimes up to 30) fine boundaries, nearly parallel to each other. Pre-existing lineage boundaries, generally parallel to the direction of growth, were barriers to the formation of polygonization boundaries and interrupted the continuity of the substructure, Fig. 2. Twin

Jan 1, 1959

By Charles Legrand

In many iron, coal and copper mines where large tonnages are known before starting operation and proper provisions can be made, the problems of electric traction by trolley locomotives are not very different from those of surface plants. In such installations the gauge of the track, the radius of curves, and the clearances, both vertical and horizontal, can be made to suit the conditions of the traffic. It is more difficult to install electric traction in mines which were started with hand tramming and where no consideration was given to the possibility of mechanical traction being used. The writer having had some experience in the installation of electric traction in copper mines, the following remarks apply more particularly to these mines. With the gauge of track usually 18 or 20 in., the weight limit of locomotives obtainable from manufacturers in this country varies from 3 to 6 tons. The full-load speed varies from 49 to 6 miles per hour. These locomotives, being made to run on very small radius curves, have a short wheel base and a long overhang from axle to coupling, which necessitates a coupling' with a good deal of lateral motion to avoid derailing the cars on sharp curves, especially if couplings are of the standard railroad automatic type. Although 3-ton locomotives will run on 12- or 16-lb. rails, it has been found more satisfactory to use 25-lb. rails, as the track keeps in much better shape, it is easier to maintain the bonding in good order, and fewer derailments from dirt on the track occur with the larger rails. Where 6-ton locomotives are used the 25-lb. rails are satisfactory, but 40-lb. rails have proved cheaper where the traffic is heavy and the ground is soft, as the track maintenance is considerably lower with the heavy rails. The locomotives will run on 15-ft. radius curves, but on through runs it is advisable not to go below 40-ft. radius. The voltage used should not exceed 250 to 275 volts, and the trolley wire should be protected, to prevent accidental contacts, in front of chutes and at all points where it is low. With the air lacking somewhat in oxygen and the heat and high humidity prevalent in many mines, this

Jan 1, 1915

By A. J. Lynch, L. Ergun, M. Oner

"A research program on modelling cement grinding circuits has been in operation at Hacettepe University, Ankara, for four years. It has concentrated so far on tube mill and air separator grinding circuits for cement clinker, with emphasis on plant sampling surveys, including axial sampling inside the tube mills. The methodology is to use plant data to build the models and to supplement this by laboratory data where necessary, for example the determination of breakage functions. The plant data come from comprehensive sampling surveys and so far 33 surveys of clinker grinding circuits have been carried out in 9 plants. The operating conditions have been• mill sizes – 3.2 to 4.8 metres diameter and 8.5 to 15 metres long,• mill feed rates – 46 to 158 tonnes per hour,• air flow through mills – 25000 to 125000 cubic metres per hour,• cement clinker work indexes – 10.3 to 18,• separator sizes – 2. to 3.1 metres diameter,• separator feed rates – 132 to 689 tonnes per hour,• separator speeds – 12.3 to 21 metres per second.The ball mill model is Whiten’s perfect mixing model and the separator model is the Tromp curve with a fish-hook. This paper emphasises on the importance of calculating the breakage rates and the discharge functions with three case studies at five different circuits which were selected for discussion because they show how particular features of circuit operation can be included in the general models. Size distributiongraphs are used to illustrate every aspect of the discussion.In case I the special emphasis on calculating the breakage rates and discharge rates separately is given in a high pressure grinding roll-ball mill-separator circuit. The tonnes of each size fraction in the mill and the calculated values of R/D, D and R are determined. The values of R per mw are also given to allow comparison with mills of other sizes. The circuit allows the comparison of the static type (V Sep) and dynamic type separators (SKS). Comparing the reduced efficiencies shows that the dynamic separator is slightly more efficient than the static one.In case 2 data are given from two compartment tube mills having the same diameter and the motor power but different ball size gradation. The breakage rate particle size variation of the second chamber of two mills indicate that having finer ball size distribution causes higher breakage rate values."

Jan 1, 2003

By V. Balasubarmanian, Rajendra Kumar

ISOTHERMAL formation of martensite in a copper-aluminum-nickel alloy was previously reported by Hull and Garwood.' In the present work an attempt has been made to investigate some of the character- istics of the formation of isothermal martensite in binary copper-aluminum alloys containing 14.00 and 14.50 pct Al, respectively. Chill-cast alloys were prepared from OFHC copper and aluminum of greater than 99.5 pct purity. They were homogenized for 24 hr at 950° C. Polished samples were soaked at 1000°C and quenched in water to retain the p phase untransformed; martensite did not form during the quench. The surface was then repolished for isothermal microscopic studies at room temperature. The salient features of the martensitic transformation in copper-aluminum alloys observed in this investigation are: a) The transformation progresses (i) by nuclea-tion at new sites and (ii) by simultaneous slow isothermal growth of existing martensite plates. Slow isothermal growth of martensite has previously been observed by Holden2 in an uranium-chromium alloy and by Hull and Garwood in copper-aluminum-nickel alloy. b) Martensite plates nucleate preferentially at the pin holes formed during the casting of the specimen, Fig. 1. c) Some of the martensite plates pass right through other plates lying in their path, Fig. 1. d) Martensite plates cross grain boundaries without any change in the direction of growth. e) An irregular network of markings, Fig. 2, appears simultaneously with the formation of martensite. It was less prominent in the case of 14.5 pct alloy. The markings may arise due to spontaneous deformation under the lattice strains of the martensitic transformation. Crossing of martensite plates was first observed by Kulin and cohen3 when a high-nickel steel was cooled to 77°K. They suggested that the rapidly advancing plates atquire considerable kinetic energy and strike the obstructing plate with a momentum so as to nucleate the process on the other side of the plate. This, however, fails to explain the present observation where the slow isothermally growing martensite plates cross each other. Such plates would not possess large momentum to bodily displace the obstructing plate. Fig. 1 shows the martensite plates crossing each other without body displacements. This should be contrasted with Fig. 3 of Kulin and Cohen's paper where crossing of plates is accompanied by shearing or body displacements of the plates. The present observations can, how-

Jan 1, 1961

By R. A. Feemster, C. M. Rader

Because of the necessity for taking regularly occurring open-flow tests in prorated high-pressure oil fields, much gas is turned to atmosphere by way of vertical vent lines leading away from the oil and gas separator. In the past, measurement of such gas has been accomplished by several methods, usually by use of the open-flow Pitot tube. The use of the closed-flow Pitot tube has been avoided apparently chiefly because the ordinary vent-line hook-up makes it necessary to apply the instrument closer to a bend, valve, or obstruction in the pipe than is recommended by rules of good practice. The many advantages that would result from the application of the closed-flow Pitot tube prompted investigation of the actual effect upon quantity rate of flow measurements computed from data obtained with the tube in a normal working position, which is closer to the tee at the base of the vent riser than is usually considered as giving highly accurate results. An effort Was first made to compare the results thus obtained to those under ideal conditions and at high velocities To make this comparison, knowledge of the characteristics of gas flowing at very high velocities is essential. Research for such information indicated that little or no work had been done that would give data necessary for such a comparison, therefore the problem was changed to a test designed to determine the relationship between quantity rates of flow as measured by an orifice meter and a Pitot tube placed at the center of a pipe eight diameters from a tee or ell at the base of a vent riser, through which gas is flowing under low pressures at very high velocities. To determine this relationship, a series of tests was run on a number of 8-in. iron-pipe vent riser., in which the Pitot tube data were taken at the position as stated above. Gas from a wet-gas gathering system was passed through an orifice meter setting and thence to atmosphere by way of the vents. Data were taken simultaneously from the orifice meter and Pitot tube from which computations for comparisons were made. The actual method of comparison is discussed later in this paper. Since Pitot-tube information is usually given in general terms, and not readily usable, it will be the purpose of this paper to discuss the applica-

Jan 1, 1934

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By W. J. Taylor

SOME eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur were naturally in the lime-kiln line, with solid fuel mixed with the ore, in the same way as common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known fact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature. This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseous fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced – 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By W. J. Taylor

Some eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur mere naturally in the limekiln line, with solid fuel mixed with the ore, in the same way = common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known Pact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature..• This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseoua fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced— 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By Martin Harper

This paper concludes a five year program on research into the use of a portable X ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively coupled plasma optical emission spectroscopy (ICP OES). The filter samples were collected using different filter holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.

Jan 1, 2007

By E. J. Duggan

It is a coincidence that the two plants in this country for treating copper ores by ammonia leaching came into existence at almost the same time, that of the Kennecott Copper Corporation at Kennecott, Alaska, in March, 1916, and that of the Calumet & Hecla Mining Co. in July of the same year. The success of both from their very beginning attests the merits of the process under widely different sets of conditions. As would be expected, in the time they have been operating these two pioneers in this field have greatly perfected their methods and improved their technic. The early difficulties inevitably encountered in undertakings of this nature have been largely surmounted and the process may now be considered to be well seasoned and matured. There have been no other commercial plants built in this country and but one elsewhere, the Bwana M'Kubwa in Northern Rhodesia, for the reason that this method of treatment may be employed on comparatively few ores. However, it has certain advantages, some of which are inherent to sand leaching processes generally and some to ammonia leaching in particular. Among these may be enumerated: (1) the avoidance of fine grinding; (2) the small amount of water required; (4) a high-grade product; (5) little likelihood of deleterious gangue constituents and fouling of solutions. It is true that great progress has been made in recent years in the flotation of the ores that come within the province of ammonia leaching. Nevertheless ammonia leaching has its possibilities and these may be overlooked in the present tendency toward the use of flotation for all ores. Probably the chief requisite to its further extension to suitable ores will be a cheap source of steam. Ammonia, the only reagent required, is unlimited in supply, readily transported and the price that is likely to obtain in the future should not make its cost at all onerous. Choice of Method for Kennecott Ores The Kennecott ores are typical limestone replacement deposits. The milling ores have a copper content of approximately 8 per cent in a limestone dolomite gangue. About half the copper occurs as sulfide, mostly chalcocite with some covellite, and the remainder in the form of the two carbonates, malachite and azurite. A comparatively coarse grind followed

Jan 1, 1934

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964