Search Documents

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By D S. Stewart, K W. Keskimaki

In 1999, the Henderson Mine commissioned the Henderson 2000 project - a new truck haulage level, a new underground crusher and a 24 kilometre conveyor system to replace a 23-year old rail haulage system. Henderson has been able to continuously improve in almost all aspects of its rubber-tired mining. The rail haulage system represented one of the last barriers to continuous improvement to the overall plant performance. Many of the lessons learned in other areas of the mine were utilised to design the truck level. This paper chronicles the benchmarking, equipment selection and design of the level. Areas covered will include haulage trucks, level layout, ore chute design, traffic control, road design and crusher layout.

Jan 1, 2000

By Richard D. Hagni

The techniques of reflected light microscopy and cathodoluminescence microscopy are uniquely suited to the study of the products from many important industrial problems. Ref1 ected 1 ight microscopy provides the means to rapidly identify the mineralogy of an industrial sample, determine the abundance of each phase, and examine the mineral intergrowths or textures. Cathodoluminescence microscopy is a relatively new instrument that provides the means to cause many minerals to cathodoluminescence under the microscopy. The cathodoluminescence of a mineral allows it to be readily distinguished from other phases that differ in cathodoluminescence but are similar in optical properties. Cathodoluminescence microscopy is especially useful to detect cathodoluminescence minerals that are present in only small quantities. Reflected 1ight microscopy and cathodoluminescence microscopy have been successfully applied in studies of beneficiation products, prediction of beneficiation and leaching problems, phosphatic iron ores and mill products, pyrometallurgical products, roasted refractory gold-bearing sulfides, ceramic build-ups, electric arc furnace and smelter dusts, and other industrial products.

Jan 1, 1993

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

By R. R. Klimpel

This paper is a summary of the author's industrial experiences on the selection and optimization of flotation reagent schemes for the recovery of gold species. The trends given are a composite of data and experiences gained on 24 different gold ores from around the globe. The primary emphasis is on the benefits of matching the associated gold mineralogy to a reagent scheme most appropriate for that mineralogy. Two general categories are discussed: the flotation of free or native gold species and the flotation of gold associated with a variety of sulfide minerals. Important plant operating factors influencing each of these two categories are presented with supporting examples. Carefully matching reagent chemistry and appropriate operating conditions to any given gold-bearing ore will not only lower the total reagent cost but, more importantly, can lead to measurable increases in gold recovery.

Jan 1, 2000

By Guocheng Pan

This paper presents-:a new multivariate mineral resource estimation model, referred to as the Related. Information (RI). Instead of relating a mineral resource descriptor directly to a set of geological variables, the RI model relates the mineral resource descriptor to a synthesized information measure RI, which is created from a set of geological variables. All of the variables are transformed into binary characteristics. This model comprises two stages of estimation: estimation of a synthesized information measure and estimation of mineral resources. The information carried by a variable is classified into three types: mineralized-barren information, mineral resource variation information, and variable-controlling information. The synthesized information measure is defined as the product of the three types of information and the responses of binary geologic characteristics. The RI model is demonstrated on the pegmatitic Nb+Ta deposits in China.

Jan 1, 1992

By G Collecutt, T O’Beirne, D Humphreys, J Greenwood

Much of our knowledge of the behaviour of underground coal dust explosions has been derived from less than full-scale experimental explosions in facilities as small as 0.25 m diameter pipes. Although a substantial body of research has been undertaken in larger galleries approaching the size of full-scale modern mine roadways, there are still questions regarding the scaling of results to full-sized roadways in modern coalmines. Questions also surround the issue of comparing or scaling results between smooth and rough walled galleries, round and rectangular galleries and galleries with differing wall thermal properties due to different materials of construction.This paper will examine the influence of gallery size, cross-section area and wall roughness and thermal properties upon the characteristics of a coal dust explosion. Data from past explosion research will be examined and assessed for its application to the problem along with theoretical considerations for these factors.Recommendations on the design and minimum appropriate size of explosion galleries for assessing the performance of explosion inerting strategies, passive and active explosion barrier performance and determination of appropriate pressure ratings for ventilation structures will be made.CITATION:Humphreys, D, Collecutt, G, Greenwood, J and O’Beirne, T, 2015. The impact of facility construction and scale on the characteristics of experimental coal dust explosions, in Proceedings The Australian Mine Ventilation Conference, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d&apos;or"" analyse, dans une approche systémique, les travaux d&apos;évaluation et de mise en valeur des gisements minéraux dans l&apos;axe de la géologie, dans l&apos;axée l&apos;ingénierie et dans I ‘axe de l&apos;économique. L’objectif est d&apos;identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l&apos;évaluation et de l&apos;exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d&apos;investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d&apos;inventorie et de classification des réserves aux méthodes d&apos;évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s&apos;étendent qu’à l&apos;axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l&apos;information dans les axes de la géologie, de l&apos;ingénierie et de l&apos;économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d&apos;évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s&apos;inspire du Code australasien, peut facilement et rapidement s&apos;intégrer dans les pratiques de l&apos;industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l&apos;échelle internationale. La proposition d&apos;utiliser les marges d&apos;erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu&apos;une période de rodage."

Jan 1, 1992

By V. K. Banakar, R. P. Rajani, A. R. Chodankar

The Afanasiy-Nikitin Seamounts (ANS) in Eastern Equatorial Indian Ocean (Figure 1) are shown to be the exposed part of the presently buried 85°E Ridge system under the Bengal Fan sediment and were emplacement around 75-80 m.y. ago (Krishna, 2003). The first recovery of ferromanganese crusts from the ANS was made during 1994, and the samples (Figure 2) provided important clues on the evolution of this seamount (Banakar et al., 1997).

By Joseph P. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies.

Jan 12, 1950

By Bukovinsky SB

The smelting, refining and hydrometallurgical operations practised in the winning of non-ferrous metals are associated with severe aqueous and high temperature corrosion problems.With the increasing costs of maintenenace and the utilization of computerization to control the processes, the trend in recent years has been to spend more capital on improved and proprietory grades of engineering materials, which offer greater reliability and more cost effective plant performance.The problems which have plagued stainless steel users for many years are the alloys&apos; poor performance in chloride or other halide media where pitting, crevice or chloride induced stress corrosion cracking may occur, have been essentially solved by the new proprietory grades. The controlled additions of minor alloying elements including rare earth metals have led to the development of stainless steels with high mechanical strengths, improved corrosion resistance, and high temperature corrosion resistance and structural stability.

Jan 1, 1985

The Gj0vik Olympic Mountain Hall is the world&apos;s largest underground cavern for public use and was created primarily to facilitate the ice hockey tournaments for the 1994 winter Olympics in Norway. The cavern has a span of 61 m, is 91 m long and is 25 m high. Ordinarily, rock caverns have a span width of 15 to 25 m, however, temporary mining caverns of up to 60 m have been excavated and natural caves with even greater dimensions occur. The Gj0vik Olympic Mountain Hall is unique as it is for public use with a capacity for 5800 spectators. Blasting was conducted with a high production rate at normal costs due to detailed planning and strict supervision of each round. The initiation system and vibration monitors were the main tools to control vibration levels and to facilitate a high production rate. It was of utmost importance that the rock remaining in the roofs and walls was of high quality after blasting to avoid rock fall, rock slides and excessive maintenance work.

Jan 1, 1995

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999