Search Documents

By E. C. Demsky

This paper describes the large diameter caisson foundation for the upstream guidewall at the Lock and Dam No. 26 (Replacement) Project. The guidewall is supported on two rows of 1.8-m diameter concrete filled caissons. The 28.8 m long caissons are embedded 15.5 m into the foundation material and have an unsupported length of 12.2 m. This paper describes the philosophy and design decisions leading to this unique caisson design. The construction success and problems for the load test caisson will be discussed. The full scale 13,350-kN caisson load test and the associated lateral load tests will be described and the test results presented.

Jan 1, 1989

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By J. E. Tobey

BECAUSE of the wide-spread publicity given to Nylon yarn as being made from ?coal, air, and water,? the general public has become conscious of the nonfuel uses of bituminous coal. Some of these uses are as filler for fertilizer, carbon for the absorption of orders, for water supply, and for the bedding of cattle. Spectacular as are these accomplishments the fact is that only a small amount of coal is used for nonfuel purposes. It is on the utilization of coal as fuel that the industry depends. Practically all the coal mines for years to come will be used for making coke for the generation of heat. Recently much attention has been paid to the significance of ash in coal. Another study worthy the interest of metallurgists in the iron and steel industries if that of Dr, Lowry of the Carnegie Institute of Technology relative to the percentage of sulphur in coal and coke.

Jan 1, 1941

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989

By AIME AIME

The American Society of Mechanical Engineers.-The semi-annual meeting of the American Society of Mechanical Engineers will be held in Detroit, Mich., June 23-26. A session will be devoted to hoisting- and conveying-machinery; and many other subjects will be treated in professional papers, among which are . Clutches (with special reference to automobile clutches); The Thermal Properties of Superheated Steam; The Horse-Power, Friction-Losses, and Efficiency of Gas- and Oil-Engines; A Journal-Friction Measuring-Machine; A Simple Method of Checking Conical Pistons for Stress, and The By-Product Coke-Oven. The usual receptions will be held and excursions will be made to manufacturing plants, the slip-building yards, and various points of interest in and around Detroit. Among the excursions' planned is one to the University of Michigan at Ann Arbor. The Gas-Power Section of the Society will hold a session, and the Society for the Promotion of Engineering Education and the Society of Automobile Engineers will hold meet-

Jan 5, 1908

By H. B. Carroll

The performance of commercially available portable instrumentation for detecting nitrogen dioxide, sulfur dioxide, and hydrogen sulfide was evaluated. Length-of-stain detector tubes from several manufacturers were included in the study. The instruments were evaluated in atmospheres with 50-and 80-percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the threshold limit values. The results from the gas analyzers were correlated with the known contaminant concentration by calculating and plotting an estimated line of regression, confidence limits, and correlation coefficient for each detector system. An increase in the relative humidity from 50 to 80 percent at /5° F changed the instrument response to the contaminants. The uncertainties in detection precision reported are for the observer-instrument system. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than from a predominant difference in the tubes.

Jan 1, 1975

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires) Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines A personal computer (PC) version of the program was completed under contract for the Bureau by MTU The purpose of this report is to document the installation and use of the PC version of the program MFIRE

Jan 1, 1990

By Ning Yang, Yuxiang Chen, Ming Chen

An ultraviolet laser Raman spectrometer was developed to detect and analyze material components of seawater, seafloor sediment and rock at a depth of 7000m maximally. Wave length of the excitation resource of the spectrometer is set to 355nm, which can enhance eigen scattered intensity and detecting sensitivity, and avoid fluorescence interference. Miniaturization design was adopted for deep-sea application. Design of the optical system and pressure cartridge, material selection and seal design of the observation window, and design of the Lithium batteries are the key technologies in the procedure of research and development. The spectrometer was carried by a Lander sank to sea bottom of the Pacific's Mariana Trench for verification. During the sea trials, data acquisition for Raman spectra was conducted for analyzing seawater in the detection area, and the spectrometer was verified synthetically. According to the data, the spectrometer is stable and practicable with high resolution and precision, and it is appropriate to detect and analyze composition of substance under the tremendous ocean.

Jan 1, 2017

The apparent small effect of skimming on desulphurization is somewhat misleading because the data was collected during the first months of use on the skimmer. During this period of time, the operators were, of course, just learning to use the equipment and, consequently, in many cases a so-called skimmed heat may have only been partially skimmed. In addition, during this period, the percentage of sulphur in the blast furnace slag was gradually increasing because of the increasing oil injection rates being employed at the blast furnace. An additional factor that cannot be disregarded is the apparent slower slag formation rate obtained in the BOF when the blast furnace slag is removed. This is evidenced at our shop by a much stronger tendency toward sparking and related lance skulling problems with deslagging, in spite of satisfactory manganese levels in the hot metal. Naturally, slower slag formation could account for poor desulphurization which would partially offset the beneficial effect of a lower sulphur input.

Jan 1, 1972

By D. Fredlund

The decommissioning of uranium tailings facilities often requires the design of a suitable cover system. In northern climatic environments there is a portion each year that can be considered to be ?inactive? while the remainder of the year can be considered to be ?active?. There are numerous engineering design assumptions required when analyzing both the ?active? and the ?inactive? portions of the year. Cover systems are subjected to complex boundary conditions and nonlinear unsaturated soil properties. The proposed paper describes the steps necessary for the preparation and the analysis of a multi-year climatic database for the design of a cover system in northern environments. The paper also explains how climate can be classified and how observed variations from one year to the next can be taken into consideration in cover design. The results of climatic records at two different sites are used to illustrate conditions that need to be taken into consideration when designing soil cover systems.

Aug 1, 2010

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the 'wet zone' with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

By W. D. Elston, A. E. McLaughlin, G. B. Hampton, W. L. Barham, J. F. Murphy, W. H. Cundiff, J. W. Mulloy, R. G. Breuer, J. W. Shaffer

Introduction Alumina (aluminum oxide) is the material from which all the world's aluminum is produced. In the Western World, all the alumina is made from bauxite by the Bayer process. In the nearly 150 years since aluminum was first isolated by Oersted, the metal has grown from a laboratory curiosity to a position of major importance in the world's commerce. In terms of annual production rates aluminum is first among nonferrous metals. Oersted's discovery-reduction of aluminum chloride with potas¬sium amalgam-was improved on by Ste. Claire Deville, whose so¬dium amalgam reduction of aluminum chloride led to the commercial production of aluminum in France in 1855. Ste. Claire Deville's method prevailed until 1886 when Charles Martin Hall and Paul T. Heroult each invented a process for the production of aluminum by the electrolysis of alumina dissolved in molten cryolite. The inven¬tion by Karl Josef Bayer in 1888 of an economical process for making very pure aluminum oxide (alumina) from bauxite established the necessary link between known ores and the Hall-Heroult reduction process. Bayer's work completed the scientific base-the ore bauxite refined to alumina by the Bayer process (U.S. Patent No. 515,895), the alumina reduced to aluminum in the Hall-Heroult cell (U.S. Patent No. 400,766--upon which today's aluminum industry is founded. Small-scale production of aluminum in the U.S. began in 1888 utilizing the Hall cell. By 1903, bauxite properties and a Bayer process refining step had been incorporated into the production activities. On this base the aluminum industry in the U.S. has grown at an annual compounded rate of 15%. Since 1946 the annual growth rate has been 10%.1 The rapid growth of the industry is the result of many factors among which are the existence of widespread bauxite ore deposits; a sound and economic production technology; and the properties of the metal-lightness, strength, ductility, good electrical and heat con¬ductivity, and pleasing appearance, which lead to ever greater de¬mands for aluminum in an industrializing society. At the inception of the industry, the only market that could be found for aluminum was in the production of cooking utensils. How¬ ever, the rapidly accelerating industrial and technological development of the Western World soon created new needs for aluminum, and today aluminum is marketed in a broad range of industrial, commer¬cial, and consumer applications. The principal uses for aluminum are:' building and construction, 22%; transportation, 18%; electrical, 13%; packaging, 11%; consumer durables, 10%; machinery and equipment, 7%; other, 19%. The 1974 production of primary alumi¬num in the world was 14.5 million short tons, which at an approximate ingot price of 40¢ per lb puts a value of $11.6 billion on the industry product prior to fabrication. While aluminum is widely distributed in the earth's crust and is a major constituent of many rocks and soils, to date no method of extraction of aluminum from such nonbauxite material has been brought to commercial practice in the Western World. In the USSR alumina is produced by the complex processing of nepheline syenite, but elsewhere all commercial production of alumina is from bauxite. A brief discussion of recent developments and other processes for alumina is included in the subsection "Other Processes for Alumina," page 19-15. In early 1973, a major U.S. aluminum producer announced the successful development of processes for the production of aluminum from aluminum chloride. This achievement promises to exert a major influence on the future of the aluminum industry. In the initial com¬mercial application of this new technology, Bayer alumina will be chlorinated, and the aluminum chloride then reduced by electrolysis. Important claims for the new processes are lower energy requirements (one-third less than obtainable in Hall cells) and reduced labor costs. Capital costs are said to be no greater than for conventional plants. While the announced intention is to produce the aluminum chlo¬ride from Bayer process alumina, the new chloride reduction process will eliminate the other raw materials, carbon and fluorides, required by the conventional Hall cells. The electrodes in the chloride cell will not be consumed on the reduction process and the electrolyte will have, as the name indicates, a chloride rather than a fluoride base. 2. Bauxite Definition and Origin. Bauxite is a naturally occurring raw material composed principally of a mixture of one or more of the hy¬drated aluminum oxide minerals gibbsite (Al2O2 3H2O), boehmite (Al2O3 H2O), and diaspore (Al2O, - H2O), and impurities of silica, iron oxide, titania, and other various elements in trace amounts. It is an end or near-end product of chemical weathering. Depending on the amount of iron impurities, the color of bauxite varies from dark red and brown to pink to white. Some bauxite is finely divided, free digging earthy material, while other forms are dense and rocky, requiring explosives in mining. Many gradational forms exist. It is one of the most variable of mineral raw materials in chemical composition and physical appearance. It is generally believed that bauxite deposits resulted from intense chemical weathering of aluminum-bearing rocks or formations under tropical or subtropical conditions with alternating wet and dry sea¬sons. Topographic conditions were favorable for drainage and the in-situ accumulation of aluminum, iron, and titanium oxides. There was low to moderate topographic relief with a minimum of erosion during long quiet periods in earth history.2 The occurrence of bauxite is widespread and it has been found on all continents except Antarctica. Production was reported from 27 countries in 1974, at which time total world production was over 79 million metric tons. Of this production 76% was from seven coun¬tries-Australia, Jamaica, Surinam, Guinea, USSR, Guyana, and Greece-which ranked in that order of production. In Table 1 are shown typical compositions of bauxite from some

Jan 1, 1985

By N. J. Grant, B. C. Giessen, M. Morris

The slvuclures of alloys in the system In-Bi have been investigated after (levy vapid queuching from the mell (splat cooling) to -190°C. Tuo-phase fields could be suppressed over most of the tota1 concentvalion range; five melastable phases a1, a2, ?, ?1. and ß exisl, of which four have simple elementtike structures. For example, ß has the A5 struclure of white till. Crystal-tographic data and coordination numbers for these phases aye given, as well as addilional information on the equilibrium diagram, where a new phase In5Bi3 teas found. THE phase diagrams of binary combinations of B elements from the groups B2, B3, B4, and B5 are usually of a simple type and show considerably fewer intermediate phases than combinations of these elements with A metals, transition metals, or the B1 noble metals. Aside from phases such as the typical B3-B5 compounds with the ZnS-B3 structure type, few stoichiometric phases are known; among them are In2Bi and 1nBi.l Nonstoichiometric phases include ß (In-Sn), a1, (In-Pb), and the tin-rich ? phases in the In-Sn, Cd-Sn, and Hg-Sn systems.' The first two phases have a close relationship to indium, while the latter group are known to be structurally related to a Sn. Thus, there are generally no immediate experimental data for the correlation of the crystal structures of B metals and B metal combinations with certain monotonously varying parameters, such as the valence electron concentration (VEC), or the average atomic size. Such parameters have been recognized as structure determining, e.g., for the transition 4 Sn — y phase,2,3 where nonintegral valence electron concentrations are encountered. It should be possible to extend such correlations to other binary systems, if nonequilibrium single-phase alloys could be produced over broad valence electron concentration ranges, and if their crystal structures could be regarded as being imposed by their electronic states. It has been shown in the case of the tin-rich 7 phases3 that alloy phases with typical crystal structures can be produced in B metal alloys rapidly quenched from the liquid to -190°C by the splat cooling technique due to Duwez,3-8 and reviewed in Refs. 5 and 6. The In-Bi system was selected because it extends over a valence electron concentration range in which several metastable, nonstoichiometrir phases could be expected to occur. Further, the low melting points of the known intermediate phases, In2Bi and InBi, Fig. 1(a), indicated low binding energies and thus possibly low driving forces for the formation Of the equilibrium structures. EXPERIMENTAL TECHNIQUES AND RESULTS The preparation of the quenched foils followed the practice described in Ref. 3. Master alloys were produced by melting of indium (99.97+) and bismuth (99.99+) in evacuated Vycor capsules or in an inert gas arc furnace; quantities of 20 mg were splat-cooled onto copper and silver substrates held at - 190°C; and crystal structures and lattice parameters were determined on a GE XRD-5 diffractometer using Cu Ka, radiation at -190°C and at room temperature. The duplication of each run with both substrates permitted the elimination of overlap of the substrate diffraction pattern and that of the investigated substance. The XRD patterns were usually taken from sin2 " = 0.03 to 0.35; the substrate was used as a means of internal calibration. The fractional accuracy of the lattice parameters of metastable phases is approximately 10-3 In the following, all percentages are in atomic percent. The stable and metastable phases found after rapid quenching to -190°C are listed in Table I, together with estimated concentration ranges and crystallographic data. The investigated alloys and phases present in them are given in Table 11. Except for the region between indium with 33 and 50 pct Bi, where a revision of the equilibrium phase diagram became necessary to include a new stoichiometric phase In5Bi3, the diffraction patterns taken after heating to room temperature agreed with those expected from the phase diagram, Fig. l(a). This suggests that the new nonstoichiometric phases are not stable at room temperature, thus following the observations made for the y phases based on tin.3 Results concerning the equilibrium phases In2Bi and In5Bi3 and the revision of the equilibrium phase diagram which is made necessary by the inclusion of In5Bi3 will be treated first. The Crystal Structure of In2Bi. Makarov7 had identified In2Bi as belonging to the AlB2-C32 type ; however, in a later paper the structure was revised.8 In2Bio was found to be of the Ni21n-B8ß type,21 with a = 5.496A, c = 6.57.9A, and N = 6 atoms per unit cell.9 This crystal structure was confirmed in the present work; definite evidence for the doubling of the c axis, as compared to the A1B2-C32 type, and for the proposed order structure, was found in the powder pattern. The observed lattice parameters agree well with those of Ref. 8; those measured at -190°C are given- in Table I. The Crystal Structure of In5Bi3. A new, equilibrium, intermediate phase was identified in slow-cooled, as-cast alloys; it was identified as In5Bi3. The structure has been worked out by Giessen and Grant;" lattice parameters at -190°C are given in Table I. This phase is probably identical with "In3Bi2", produced by vapor deposition techniques, but not recognized as an equilibrium phase by Palatnik et a1.11 After completion of the present work, the existence of In5Bi3 has also been demonstrated by superconductivity measurements on In-Bi alloys.20

Jan 1, 1968

By N. K. Mendiratta

Diethylenetriamine (DETA) is known to be an effective pyrrhotite depressant in pentlandite flotation. It has been reported recently that its performance becomes more consistent when the reagent is used in conjunction with sulfur dioxide (SO2). In the present investigation, the effects of DETA and SO32- ions on the changes in the hydrophobicity of pyrrhotite electrode have been studied at pH 6.8. The results show that both DETA and SO32- can reduce the water contact angles of pyrrhotite; however, the contact angles can be reduced to zero only in the presence of the SO32- ions. This finding may be attributed to the ability of the SO32- ions to reduce the polysulfides formed on pyrrhotite by superficial oxidation, which may in turn provides an explanation for the robust performance of DETA/SO2 combination.

Jan 1, 2001

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

By P. R. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentratio� meets discharge standards.

Jan 1, 1992

By Marc E. Orman, Todd V. Ramey, Mark E. Smith

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts. In northern Chile the soils often c?ntain very high concentrations of soluble salts (nitrates, potas­smm, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and trig­gers differential settlement. If the settlement is great enough, the geomembrane tears, the leakage increases, triggering more dif­ferential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will under­go a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geomembrane with suit­able flexibility under axi-symmetric (multi-axial) load condi­tions to tolerate the predicted settlement.

Jan 1, 1996

By Ray D. Peterson, Garry G. Blagg

"Molten aluminum is routinely transported hundreds of miles to customers in large ""over-the-road"" crucibles. This is especially common for aluminum recycling organizations handling scrap and by-products. Receiving the aluminum in a molten form can save the customer time and money since in-house melting costs and capital equipment can be avoided. Additionally, the alloy can be on specification and nearly ready to use for the casting operation.A number of transport crucible designs are currently in use. The specifics of each design are based on the needs of the customer, the equipment used at both the producer and the consumer, and over-the-road transportation constraints. Crucibles are designed to maximize carrying capacity, and refractory life while minimizing heat flow and dead weight. These conflicting demands place difficult design criteria on the design engineer.This paper will review the basic advantages and disadvantages associated with molten metal transport, give examples of the design restrictions and examine several types design of crucibles currently in use."

Jan 1, 2000