Search Documents

By C. H. Mathewson, J. A. Collins

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development's AM5000, Davis's, or Taylor's Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD's, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

By Coulter L. J

THE method of stope surveying as practised at the Mount Lyell Company's mines has been evolved out of the exigencies created by special conditions. It presents some novel features, and has proved effective for all requirements. All stope measurement work is brought under one complete system, to which office methods are standardized. Before proceeding to deal with the subject a brief description of the physical characteristics of the ore-bodies of each mine and the method of stoping will serve to show, cause ,for departure from ordinary survey practice.NORTH LYELL MINEThe ore-bodies of this mine occur on or near the conglomerate schist contact, and, being probably the result of replacements of both rocks, they rarely present any definite walls. It is usual for the payable material to merge into the respective countryrocks, and the limit of the occurrence is defined rather by assay value than by any distinct natural boundaries. The general configuration of these ore-bodies, therefore, is highly erratic both in horizontal and vertical section, so that, in order to obtain an accurate record of any occurrence, the measurement of the actual contour at short vertical intervals is essential.Stoping is carried out on a modification of the "rill." system, perhaps more properly described as "arched back" or "dome" stoping. Mullock rises are placed in as convenient positions as the erratic configuration of each ore-body will allow, and aroundthese rises the back is kept well arched, both longitudinally and transversely. The larger stopes are divided into arbitrary sections in which ore-breaking and mullocking are carried out in rotation, so that the whole of the excavation is seldom open for measuring at anyone particular time. Stacking or square-setting on the...

Jan 1, 1915

By M. Friedman

Applications of rock mechanics to the design of engineering structures in rock involve the assumption that the stresses are due entirely to the present applied loads. For instance, it is assumed that the vertical normal stress in undisturbed rock free of topographic effects is equal to the weight per unit area of the overburden. In fact, vertical dilatational strains associated with stresses of more than 100 times the present overburden pressure have been measured by strain-relief methods on outcrops. 1,2 The notion of residual strain (stress) or latent stress3 seems unassailable; and indeed this has long been recognized by metallurgists. It is difficult, however, to assess the residual component of the in-situ state of elastic strain with conventional strain relief methods employed in mines or down boreholes. That is, in principle, the in-situ state results from the superposition of present applied loads (natural or man- induced) and potentially recoverable elastic strains (stresses) that exist in a given volume of material even though there are no external forces across the boundaries of the body (Voight,4 and Fig, 1). Accordingly, only in unloaded blocks can the true residual strains be measured by strain relief methods. Using X-rays, the elastic strains locked within the quartz grains or crystals of a rock can be measured. These strains are known to persist even when the rock is reduced to small chips but to vanish when the rock is disaggregated and the grains are powdered. Although we have just begun to investigate the mechanisms by which the strains are stored (see Preliminary Results), we believe that "pressure solution'' at grain boundaries, secondary cementation under load, permanent ("plastic") deformation, and temperature changes are possible processes. In any event, in our study of naturally deformed rocks, it is significant that we are work-

Jan 1, 1972

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By J. A. Collins, C. H. Mathewson

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

CHUQUICAMATA, as the Chile Copper Company's mine is known, has the largest developed deposit of copper ore in the world. Indeed, it is improbable that its equal will ever be found. The Union Miniére du Haut Katanga, operating in the Belgian Congo, may some day surpass Chuquicamata in the total amount of copper produced; or one of the companies developing the rich copper region of Northern Rhodesia may ultimately outdo it. But in each instance, the ore will come from a group of mines separated by 80 miles or more; whereas the deposit at Chuquicamata is one vast integral mass containing as a minimum probably 1,000,000,000 tons of ore, averaging better than 8.5 per cent copper, and as a maximum-well, most any reasonable figure might err on the low side. Utah Copper approaches Chuquicamata more nearly than any other in tonnage of exploitable ore; but Utah's ore is less than half as rich. The figure for the aggregate copper content of the reasonably assured ore at Chuquicamata is breath-taking at 50,000,000,000 pounds. Other distinctions has Chuquicamata: It was the first of the Porphyry Coppers to use leaching as the method of treating the ore; its plant cost for producing is lower than that of any of the others, only Braden and Utah being close rivals; and it was worked for its copper long before any of the others. According to an authentic article published in Ingeniería Internacional (May, v 1982) the Incas smelted copper ores from Chuquicamata prior to 1536. Diego de ALnagro, to whom Charles V, King of Spain, generously allotted a one-fourth portion of South America lying south of Cuzco, the Inca metropolis, made an expedition into Chile in 1534. Better known to history, perhaps, is Pizarro, who was awarded the area immediately north, and who proceeded

Jan 1, 1933

By F. R. Morral, E. P. Miller

Hot-dipped heat-treated zinc coatings on sheet steel were examined with X-rays. The phases identified were compared with those listed in the modern literature 01 the zinc-iron system. The zeta (FeZn13) phase is shown to correspond to the phase found by Schueler (1925) in heat-treated zinc coatings. An investigation was undertaken to determine the phases present in hot-dipped heat-treated zinc coatings on steel sheets and wire. This kind of coating on wire was studied some years ago by Schuelerl by microscopic and chemical methods. He reported a new phase, FeZn10. Later, Clark and Stillwell,2 using X-ray crystal analysis, identified a new phase in ordinary galva. nized wire, which was assumed to be the FeZn10 phase. Since the extensive review of the iron-zinc alloys presented a few years ago,3 much new work has been published, some of which5-l6 was too late to be included in the recent edition (1939) of the American Society for Metals' Handbook.4 Figs. 1 and 2 are reproductions of the latest iron-zinc diagram proposed by Schramml1 as a result of his investigations by microscopic, thermal, magnetic susceptibility and X-ray methods. Table 1 summarizes all the known published X-ray data of the phases Present. The solubility of iron in zinc has been determined by x-ray methods.10 In the same manner the homogeneity range of the P phase was studiedlo using the principle that the parameter of an intermetallic compound changes while the concentration of One of the constituents changes. Schramm10 has found some 80 alpha lines in X-ray powder photograms of phase d1, and from these he believes that this phase is related to the P phase. Previous investi-

Jan 1, 1941

By Rudolf K. Berkhard

Static soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the application of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the pkactical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes. Methods Static Method.—The first and oldest tests to investigate the bearing capacity of the soil were carried out by static weights. The penetration of these weights, however, depends not only on the soil but also on the size and the form of their lower surface. The length of time the load acts is also important. To imitate actual field conditions, heavy weights and lengthy tests are required, both of which are expensive. Furthermore, the influence of static weights affects only the surface and does not penetrate into deeper strata, therefore substitutes and supplements for static tests have to include the time factor and consequently lead to dynamic investigations. Such dynamic investigations also affect

Jan 1, 1940

By Oliver C. Ralston

A definite field of usefulness has developed for the brine-leaching processes of removing lead from ores and other products, so this paper reviews the developments, both in practice and in research, that have taken place since the publication of two earlier papers on this subject.' Several commercial plants are now in operation and a number of semi-commercial test plants have been operated in an effort to determine the limitations of brine leaching and to compare the results with other forms of treatment. Briefly, the brine leaching of lead depends on the fact that lead chloride and lead sulfate are soluble in saturated sodium-chloride solutions. In dilute brines, the solubility of the lead salt is less than in pure water; but in the strong brines, the solubility is greater than in pure water due, supposedly, to the formation of a double sodium-lead chloride. This is seen in Fig. 1, which shows the results of M. Demassieux2 on the solubility of lead chloride in sodium-chloride solutions of different concentrations and at three temperatures. The curves are not those given by Demassieux but are calculated from his results in order to convert them to units common in metallurgical work. The right-hand branch of each curve shows that if the solution is kept in contact with solid sodium chloride the lead chloride can be almost entirely displaced from solution, but that brines which are saturated with sodium chloride, but are not in contact with the solid salt, have a very high solubility for lead chloride. The diagram gives the analysis of the solution in grams of lead per liter, although the substance actually in solution is lead chloride. At 100" C. as much as 100 gm. of lead per liter can be obtained; but at lower tem-

Jan 1, 1924

By L. D. Dougan, J. V. N. Dorr

PaGE Geological Conditions......................... 78 Development of Elko Prince Property.................. 78 Prince Vein.............................. 79 Mining Practice.............*.'.......:...... SO Milling Practice............................ 84 Power Plant............................... 96 Construction Costs.......................... 97 Geological Conditions The Elko Prince mine is in the Gold Circle district, Nevada, about 155 miles (2. 4 km.) from the town of Midas, 55 miles (88.5 km.) west of Battle Mountain and 50 miles (8.5 km.) northeast of Golconda. The district is described by Emmons in U. S. Geological Survey Bulletin 408, 1910. Little was said of the Elko Prince, however, as only a small amount of work had then been completed. The geological structure of the region is simple. The oldest exposed formation, covering most of the area, is rhyolite, which has a light-colored devitrified groundmass enclosing phenocrysts of feldspar, quartz, and magnetite. It has been somewhat weathered and partially stained with oxide of iron. There are several outcrops of andesite which cut the rhyolite. The ore deposits occur as fissure veins, replacement veins, and sheeted zones. The Elko Prince vein is of the first type. The rhyolite near the veins is silicified, stained with oxide of iron, and, at some localities, replaced by ore, or is so permeated by metals as to be classed as ore. The vein filling consists chiefly of quartz, and the values consist entirely of gold and silver. Part of the gold exists as the native metal and part is associated with pyrite. Silver occurs free and as argentite in banded streaks through the vein. These veins trend in a northwesterly direction, with dips varying from 65' to vertical. Development of Elko Prince Property Gold was discovered in the district in the Fall of 1907, and a charac-stic rush followed The town of Midas was laid out and shortly had

Jan 1, 1919

By Rudolf K. Berkhard

Static soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the application of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the pkactical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes. Methods Static Method.—The first and oldest tests to investigate the bearing capacity of the soil were carried out by static weights. The penetration of these weights, however, depends not only on the soil but also on the size and the form of their lower surface. The length of time the load acts is also important. To imitate actual field conditions, heavy weights and lengthy tests are required, both of which are expensive. Furthermore, the influence of static weights affects only the surface and does not penetrate into deeper strata, therefore substitutes and supplements for static tests have to include the time factor and consequently lead to dynamic investigations. Such dynamic investigations also affect

Jan 1, 1940

By C. Q. Payne

The art of crushing ores and other materials by means of rolls is a comparatively recent one. While the first record of rolls using iron crushing-surfaces dates hack to the year 1806, when they were employed in Cornwall, their principal developmcnt has taken place during the past 30 years. To Stephen R. Erom belongs the credit of the pioneer in introducing the belted high-speed roll, which has had its origin and a marked development in this country. His notable contrib'ution to the art was in the use of a single bed-plate or frame supporting the roll-shafts, and to which levers holding the mova, ble roll-bearings were pivoted. He also made use of steel tension-rods to support the crushing-strains, and of hammered-steel tires for the crushing-surfaces. These changes brought the design of crushing-rolls to a high level. Following closely thereon, about 1885, W. R. Eckart conceived the idea of the swivel or ball-and-socket support for the roll-shaft bearings. This is an excellent mechanical conception, especially for bearings held against a spring pressure, and while it may not be necessary for all types of rolls, yet it has been quite generally adopted by other roll-designers, and illustrates the refinement which roll-construction has now reached. Other engineers, as, for example, Argall, Vezin, Roger, and Sturtevant, to mention only a few among many, have also given the closest attention to the various details of rolls, such as the frame, springe, bearings, and shafts, and have developed many novel and original designs. It has remained, however, for the boldness and originality of Mr. Edison to extend the field of crushing-rolls in two new directions, and to cause them to ex-

Jan 1, 1913

By F. C. Langenberg

DURING the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point: The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the. bars was tested in this manner and in no instance could any difference in structure be detected between the three specimens.1

Jan 2, 1915

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By V. Caps

Gold has been often used as an alloying component in order to increase or modify the catalytic properties of an active metal. For example, in the hydroconversion of methylcyclopentane, Riahi et al [1] shown that the addition of gold to palladium or platinum enhances the activity which becomes greater than that of the pure metals whereas the selectivity towards products resulting from ring expansion increases. Molenbroek et al [2] presented a detailed study on Ni-Au catalysts which exhibit activity for steam reforming and have been proved to be more resistant toward carbon formation than the pure Ni catalysts. Blocking of highly reactive Ni edge and kink sites by Au atoms is assumed to be the reason for the increased robustness of the Ni-Au catalyst. Nevertheless, the own catalytic properties of pure gold have been almost ignored up to the pioneering work of Haruta et al [3] which demonstrates the high activity of gold for CO oxidation at low temperatures. Other reactions such as WGS reaction, propylene epoxidation or benzene total oxidation have then been shown to be catalyzed by gold [4]. This discovery induced the publication of papers devoted to analyze the different factors controlling the activity of gold catalysts. Among them the most relevant appears to be the gold particle size, the nature of the support [5] and the preparation methods [6]. Clearly distinguish between support and size effect is not straightforward. Indeed, the calcination step often needed to synthesize supported catalysts on different supports, leads to different particle sizes showing that particle size and support are interdependent. To circumvent this difficulty, Au-based supported catalysts have been synthesized by using laser vaporization and low energy cluster beam deposition. The as prepared catalysts have then been characterized and tested in CO oxidation reaction.

Oct 1, 2003

By L. Segle, R. Resnick

NUMEROUS experiments in the past few years have proven that void formation occurs quite generally in the diffusion zone of bimetal specimens1-4 The phenomenon has been explained in terms of the accumulation of lattice vacancies resulting from unequal diffusion of the constituents and their eventual precipitation as holes.= Attention has recently been directed to the fact that voids also form within homogeneous metals during high-temperature creep.' The idea has been put forward that these voids form by the condensation of excess lattice vacancies generated by intersecting dislocations.".' If the precipitation of lattice vacancies from solution is treated as a nucleation and growth process, the predicted vacancy concentration for homogeneous nucleation of voids at an observable rate is 100 to 1000 times the normal thermal equilibrium concentration. It appears that voids actually form during diffusion at vacancy supersaturations which are much lower than this8 According to the calculations of Machlin,' the same must be true for voids formed in homogeneous metals during creep, if these are considered to arise from the precipitation of lattice vacancies. Therefore, if the vacancy mechanism is valid, it seems that the holes which form in diffusion and creep specimens are heterogeneously nucleated by imperfections or impurities in the metal. Irregularities in the frequency and distribution of voids in diffusion couples bear out this explanation.' , It is not known at the present time what the nuclei are on which vacancies condense. Various investigators have speculated that they could be certain dislocation configurations, already existing voids produced during solidification or working, gas pockets, or inclusions in the metal. Relatedly, the precise value of the degree of vacancy supersatura-tion for void nucleation is still uncertain. An initial attempt to estimate this value from diffusion data, made by Balluffi, indicated that voids form in diffusion couples at vacancy concentrations which may

Jan 1, 1958