Search Documents

By P. J. Sylvester, S. J. Piercey, S. Maloney, S. M. Brueckner, L. Pilgrim, D. Hyde, G. Ogilvie

The 1806 zone is part of a Au-rich volcanogenic massive sulfide deposit at the Rambler Camp on the Baie \/erte Peninsula, northwestern Newfoundland, and is characterized by high Au grades (3.97 g/t), relatively low Cu and Zn grades (0.60 wt% Cu, 1.17 wt% Zn), and moderate Ag grades (27.83 g/t) at ca. 0.37 Mt ore. Gold and Ag occur as electrum and different Ag varieties including Ag-Hg ± Au alloys, miargyrite, and pyrargyrite that occur often in close proximity to electrum. Additionally, Ag-, As-, Sb-, and Sn-bearing sulfosalts are frequently observed and usually close to electrum. These textural relations strongly favor a syngenetic/magmatic origin for the 1806 zone, despite having a metamorphic overprint.

Jan 1, 2011

By John F. Elliott

Because of the importance of the steel industry in the economy, a program of study was undertaken to develop a computer model by which it would be possible to predict the need of the industry for raw materials and energy in the next several decades. This report gives the results obtained it a preliminary 6-month program.

Jan 1, 1973

By S. P. Kinney

The Department of the Interior has recently investigated the atmospheric conditions in tunnels of the Union Pacific Railroad in Utah and Wyoming , by observations made from the cabs of freight locomotives . This work was conducted by the Bureau of Mines at the request of , and in cooperation with , the Union Pacific Railroad Co .. and was brought about by several accidents to members of engine crews while passing through tunnels , from pollution of the tunnel air by exhaust gases from freight locomotives . The object was to determine the cause of gassing accidents , by examining into composition of the air in locomotive cabs while passing through railroad turmels ; to learn the effect of these conditions on the engine crew; and to provide a means of protection for the men so exposed . Gas samples and temperature readings taken in the cabs of locomotives were used in studying the atmospheric conditions to which the locomotive crews were exposed . The symptoms and the physiologica effects produced in men exposed to the atmospheres encountered were studied . The pulse rates and body temperatures were taken , and the determinations of the carbon monoxide content of the blood were made . Various methods for the prevention of gassing and for the protection of men therefrom were considered and tested , among which were the use of mechanical devices for deflecting the smoke away from the engine cab, and the use of various types of gas masks and breathing apparatus . While this investigation is a part of the safety work of the Bureau of Mines in connection with hazards from atmospheres containing carbon monoxide ( CO ) , the results are of particular value to railroads operating steam locomotives through tunnels , and are also valuable to other industries where atmospheres having poisonous gases or of a high temperature and humidity may be present . The results may be summarized as follows :

Jun 1, 1923

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals'-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By Jorgen Elbrond

The capacity calculation of complex transportation systems involving variable activity times such as encountered in the mining industry are often worked out by means of simulation, which reconstructs waiting times and cycle times. The queuing theory, which mathematically calculates waiting times, has been used mainly to describe the, phenomena. This is due partly to the difficulties encountered in modelling complex systems and partly to the difficulty of reconciling the required time distribution laws with the real phenomena by means of the queuing theory. It is, however, obvious that formulas for capacity calculations would be preferable to simulation procedures because of their higher calculation speed, shorter and more flexible programs and shorter programming work. The calculation procedure presented in this paper is composed of some rather simple models, which are based on the queuing theory, and on some probabilistic and some deterministic considerations. The models are supported by observations, and to some extent by simulations. It has been attempted to find all the components of the cycle time and to include them in a comprehensive model. It is the intention to demonstrate that even quite complex mine transportation systems can be treated by means of the queuing theory with the advantages mentionned above and, without sacrificing the precision of the estimates. The speed of calculation of a wide range of parameter combinations is such that the procedure can be used extensively by a project engineer in the search for optimal modifications of the entire transportation system.

Jan 1, 1979

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By G. L. Oldright

[This paper is the fifth 4/ of a series of publications on smelting in the load blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation, and to correlate the behavior of the furnace at various tines with the main factors governing the operation of the blast furnace, and metallurgical losses.]

Jan 1, 1929

By J. Winlock

To have been chosen by you to give the Howe Memorial Lecture is the greatest honor I have ever had and I should like to have you know that I appreciate it deeply. Many years ago I had the privilege and the pleasure of working with Professor Howe in the private laboratory which he had established in his home at Bedford Hills, New York. Without doubt he was one of the world&apos;s greatest metallurgists and so you can imagine what a difficult task it has been for me to live up to his teachings. Every morning Professor Howe would outline the work he wanted done and the recollections of those conferences are clear to me to this day. Sometimes he would ask me to ride in his automobile and the chauffeur had full instructions to go no more than fifteen miles an hour. If he did so, Professor Howe was sure to rap upon the man&apos;s shoulder with his cane. I assure you, however, Professor Howe&apos;s thinking was not at that rate. His homely advice, his patience and his perfect control of the English language still impress me. Many times I heard him dictate a complicated paper on metallurgy and never find it necessary to change a single word. There are no better words to describe the character of Professor Howe, in my opinion, than those used by Professor Sauveur when he presented the John Fritz Medal to him in 1917: "Lover of justice and humanity Public servant and public benefactor, Master of the English Language, Loyal and devoted friend, Untiring and unselfish worker in an important field of science." I hope you will bear with me with the same patience and understanding which he used to give to me. The peculiar behavior of steel at the yield point has long been known and has been the subject of much research, both in this country and abroad.&apos;,&apos; Many theories, including some of mine and my colleagues, have been suggested, but none of them, in our opinion, fully explains to our satisfaction why the phenomena occur. Of particular importance has been the work of Nadai,3 Siebel and Pomp,&apos; Sachs and Fiek,5 Rawdon,0 Kenyon and Burns,&apos; Gensamer," Gensamer and Meh1,0 Davenport and Bain,&apos;" Fell," Deutler,12 Brinkman,13 MacGregor,14 Hollomon,15 Cot-trell,16 and Palm." The question of what is occurring during this singular behavior is not only of interest from an academic point of view, but is of great practical importance for at least two reasons: 1—The highly localized plastic flow which occurs during the deep drawing of light-gage steel gives rise to surface markings which seriously mar its appearance, Fig. 1. If the forces causing the deformation are primarily tensile forces, these surface markings occur as depressions in the surface. Whereas, if the forces causing the deformation are primarily compressive, irregular lines of elevations occur. These surface markings are known as Luder&apos;s lines, Hartmann lines, the Piobert affect, and, in the shop, as "stretcher strains." 2—The steel is in the most suitable condition for deep drawing after the yield point phenomena have been removed. When this is done, the steel may be deep drawn more easily and to a greater extent.&apos; It should be mentioned that steel is not the only metal which shows this peculiar behavior at the yield point. Stretcher strains occur, also, during the deformation of some copper-nickel-zinc alloys." The purpose of this paper is not an attempt to describe what causes the steel to behave in this peculiar manner, but an attempt: l—to describe what is taking place at the yield point; and 2—to show the influence of the rate of deformation on the tensile properties of some plain carbon steels. As is well-known, there are two methods of deforming a metal in tension: 1—by actually hanging an increasing amount of dead weight on the metal; or 2—by deforming the metal at some given rate or rates by means of oil pressure cylinders, screws, etc. With the first method, the load is always present and, clearly, no drop in load can ever occur while the steel is deforming. With the second method, the registered load is the resistance of the steel to the deformation being imposed upon it. The second method is the one most widely used, and is the one referred to throughout this paper. In order to describe clearly what is occurring at the yield point in steel, it will help, I believe, if a description is first given of what occurs when alumi-

Jan 1, 1954

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset&apos; that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By W. E. C. Coxe

Many of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission mas accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which he furnished for the head of the rail could net be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author&apos;s name, with author&apos;s degrees, titles, position. Synopsis, including a brief statement of conclusions. Index, only if paper is long and involved. Introduction. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers&apos; Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King&apos;s English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the &apos;single&apos; type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol %is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d&apos;Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramms metre per second per second (kg m/s&apos;). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. I, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers&apos; errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standardsymbols as laid down in British Standard 1219C shoulrl be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author&apos;s conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author&apos;s name, with author&apos;s degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers&apos; Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King&apos;s English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the &apos;single&apos; type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d&apos;Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers&apos; errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author&apos;s conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publicatiol1 of technical notes taking up to three pages (maximum 3000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute asa body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author&apos;s name, with author&apos;s degrees, titles, position. Synopsis. Index, only if paper is long and involved Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers&apos; Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King&apos;s English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the &apos;single&apos; type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d&apos;Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers&apos; errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author&apos;s conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council. Although the worldwide readership of the Journal results in a preference for papers in English, the Council treats papers in Afrikaans on an equal basis, but, to meet the needs of the majority of readers, an English summary of some 5OO to 750 words should be provided.

Jan 1, 1984

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent;, a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012