Search Documents

By J. A. Younkins. J. P. Proctor, E. D. Hummer

Comparatively little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission Of any effluent Of high ''lid 'content to be rep1aced by 'lean water in Order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the Purpose of this Paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settlillg and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." General Arrangement of Water System So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers,1,2 The washer, which handles o to 4-in, raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. I) consists of twin 48.in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By George E. Cole

While many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg' Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada's mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By George E. Cole

While many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas inaccessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Although summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transportation has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys occupied by lakes and rivers Or by many low-lying portions covered with muskeg' Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer distances but it is not every water route that will satisfy the conditions of loading freight on to a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer Over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc- tion over a long period, it may be necessary to haul large quantities of supplies during the winter. This seasonal problem, particularly for the out-of-the-way properties, is SO important and demanding as to make it a major operation in the life of the mine. The -use of the tractor during winter months for heavy machinery and bulk supplies, and the use of the airplane throughout the year for the transportation of personnel and for emergency requirements, have greatly improved transportation to places that are inaccessible by rail. Canada has pioneered in both these methods. Development oF Transportation Twenty-two years have seen a marked change in transportation methods in Canada's mining country. Horse-drawn sleighs have given way to the tractor and that to some extent has been supplanted by the airplane. One of the earliest ventures involving transportation of considerable magnitude was that of the Mandy mine, on Schist at in northern Manitoba. According to accounts of early mining activities in Manitoba, the Mandy mine, beginning December 1916, had 3300 tons of ore hauled 40 miles by sleigh to Saskatchewan River and in summer this was conveyed by barge to The Pas, 130 miles, and then by railroad to Trail, British Columbia, 1200 miles. The mine shipped 6000 tons of ore in 1918 and 15,000 tons in 1919. In winter of the latter year, as many as 300 teams of horses were used on the 40-mile stretch to

Jan 1, 1943

By James H. Courtright, Kenyon Richard

L. H. Hart (Chief Geologist, American Smelting & Refining Co.)— Because of a widely recognized association between breccia pipes of one form or another and many important copper deposits, conditions under which breccia pipes develop have been of great scientific interest for many years. Since these phenomena first attracted attention, many theories have been advanced to explain their origin. This is not unexpected, since it is likely that they have been formed by and under a wide range of conditions. Moreover, the entire subject is confused by the fact that the term brec-cia pipe is applied to a wide variety of occurrences. To discuss any part of the subject intelligently, therefore, it is necessary to start with definitions of the terms used. In their discussion of the Toquepala deposit, Richard and Courtright have carefully defined the terms they have used in their presentation of a very logical geological history of Toquepala breccias. This is a real contribution, as there is no reference in the literature known to the writer where the history of a series of breccia pipe epochs, confined essentially within one channelway, may be read with the degree of certainty that appears to be possible at Toquepala. Although the following comments are intended primarily to emphasize points brought out in the article by Richard and Courtright, certan subsequent detailed mapping by Hollister and Houston7 within the main central mineralized area of the Toquepala deposits not only supports most of Richard's and Courtright's con- clusions but also contributes additional facts that strengthen and broaden the whole concept of the origin of the Toquepala breccia pipes. In detailed mapping by Hollister and Houston,' the most significant feature disclosed is a well developed system of concentric fracturing in rocks peripheral to the main breccia pipe throughout an arc of 300°, interrupted only by the late dacite agglomerate in the north quadrant. Although Richard and Courtright noted that such fractures were developed in the southern and southeastern areas, continuity in the east and west quadrants is established by consistent orientation of the stronger set of fractures and joints. The existence of these structural weakness trends is emphasized by the emplacement of dike-like phenomena in and along members of this fracture system. Richard and Courtright described one of these dikes in the southeast quadrant. They referred to it as a ring-dike, composed of dacite porphyry. This suggests an apparent structural control of at least a part of the dacite porphyry intrusion by features related to the Toquepala breccia pipe center. This raises a perplexing question, since the dacite porphyry intrusion had been presumed to antedate breccia pipe activity. However, if this ring-dike is related to the breccia pipe center, it may indicate that some part of the dacite porphyry intrusion advanced in a manner resulting in an intensely localized stress center, which produced the concentrically arranged fracture system. The ring-dike would then appear to be evidence strongly sug-

Jan 1, 1959

By R. Taggart, D. H. Polonis, J. C. McMillan

Thin foil electron microscopy techniques have been used to study the micros tructure of a Ti- 7.5 wt pct vanadium alloy in the quenched and aged cond_itions. Selected area diffraction has identified a (1011) twinning mode accompanying the martens ite t9.an.sfo?rn~ation. Precipitation of the 0 phase during the aging of quenched alloys has been obsevced to occuv in the form of plates and needles with preferential growth along the (1120) direction in the a' matrix. In the present work, the micro structures of quenched and aged alloys of the 0 isomorphous Ti-V system have been investigated by means of thin-foil electron-microscopy techniques. Most of the previous studies of martensitic phases in titanium-base alloys have utilized optical microscopy and X-ray diffraction techniques. The application of transmission electron microscopy is more recent, and only a few such studies have been reported.1-5 This paper is concerned particularly with the crystallographic nature of substructures formed in the martensitic a' plates. The early stages of aging or tempering have also been examined to determine the modes of precipitation from the martensitic solid solutions. Such information is essential in studying strengthening mechanisms and in determining the feasibility of high-strength rnartensitic alloys based on titanium. Liu and Margolin6 reported several types of substructures within the martensitic plates of quenched Ti-Mn alloys. It was later suggested by Liu7 that the structure of martensitic plates might be very complex and not single crystals as normally assumed. The sub-markings could not be identified with the two possible habit-plane orientations {334}ß and {344}ß, and it was not positively determined whether they are associated with mechanical twinning. The recent studies by Armitage5 on titanium martensites in a variety of commercial alloys have indicated that twinning does not generally accompany the transformation. This observation is in accordance with the Mackenzie and Bowles model for the transformation in pure titanium8 which suggests that twinning is not to be expected. However, a number of other recent investigators have reported twinlike substructures in the martensitic plates of several titanium systems including commercia1 titanium,2,3 Ti-Cu,5,9 Ti-Ta,1 and the commercial alloy Ti-8A1-1Mo-1V. Blackburn* has reported that the structure of quenched Ti-8A1-1Mo-1V depends on the prior solution temperature. He identified two types of martensitic structures, one of which is described as a heavily faulted hcp or twinned fcc structure and the other an hcp structure with a high internal dislocation density. The latter type exhibited some twinning with a (1011) twin plane. EXPERIMENTAL PROCEDURES AND RESULTS The alloy used in the present work was a 7.5 wt pct V alloy that was prepared by conventional arc-melting techniques. This alloy composition was selected

Jan 1, 1968

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By A. W. Dana, F. J. Shortsleeve, A. R. Troiano

The phenomenon of flake formation which may occur during cooling or room temperature aging of large steel sections is caused by a combination of hydrogen and stress. As such, the transformation characteristics of austenite in a particular section play a major role in the occurrence of flakes. Isothermal and continuous cooling studies demonstrated that flake formation is particularly sensitive to nature, distribution, and relative proportions of the microconstituents in the cooled sections. In the absence of transformation stresses, abnormally high hydrogen contents could be tolerated without flaking. Flakes were not found in the absence of transformation stresses. No correlation existed between average hydrogen content and flake formation where cooling stresses were low. Hydrogen in the steel was a necessary but not sufficient condition for flake formation. DESPITE a long history of laboratory and commercial investigations, the mechanics of hairline crack or flake formation in large steel sections remains unresolved. Recent publications1-5 emphasize that flaking is still a serious problem.* immediate cause of flaking is the pressure exerted by entrapped hydrogen gas that collects in small internal cavities or voids during cooling. When the temperature of steel is low enough to preclude extensive plastic flow, the cavity pressures cause local brittle fractures (flakes). 2—The microsegregation and transformation stress theory. According to this theory, flaking results from stresses arising from the volume changes accompanying the formation of martensite and/or low temperature bainite after a large portion of the section has transformed at elevated temperatures. The proponents of the hydrogen theory suggest that stresses from other sources may be additive to the stresses produced by hydrogen and may, in some cases, provide the increment of stress necessary to produce flakes. However, the critical aspect of this theory is that no stress, except that produced by hydrogen pressure, is believed to be sufficient in itself to produce flakes. For practical considerations, this means that the only safe thermal cycle is one that reduces the hydrogen content to some low critical level below which flaking will not occur regardless of the state of transformation. On the other hand, the transformation stress theory does not rule out the embrittling effect of hydrogen. This theory simply proposes that flaking does not occur in the absence of transformation stresses. With the transformation stress theory as a basis, commercial antiflaking cycles would be designed to complete the transformation of austenite prior to cooling to ambient temperatures. Both of these theories appear compatible with industrial experience. Antiflaking cycles, such as cooling at extremely conservative rates or soaking for periods of time in the upper subcritical temperature ranges prior to cooling to ambient temperatures, may allow the following: 1—diffusion of hydrogen out of the section and, as a consequence, reduction of the hydrogen content to some safe minimum value (hydrogen pressure theory) and 2—complete decomposition of the austenite at rela-

Jan 1, 1956

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y'; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

By G A Brown

Environmental legislation is changing rapidly throughout Australia at the present time, and with that change comes additional responsibilities for the mining and petroleum industries. Among the many changes that are being made are increased penalties for both criminal and accidental environmental impairment. The defences for criminal offences are limited and for other offences the laws may impose strict liability - in effect the offender is guilty until proven innocent. Mines may be included under contaminated land legislation, creating additional liabilities for clean-up, rehabilitation and long-term management. It is not unknown in Australia for the value of a mortgaged property to be less than the amount of the environmental liability acquired by a mortgagor in possession due to contamination of the site. An essential part of the management program for resource projects is now the regular conduct of an environmental audit, the results of which assist in the management of the legal and financial liabilities facing company directors and managers. The audit can also assist with negotiations with government agencies, staff, unions, insurers, Aboriginal and other community groups. An environmental audit may also help to ensure that companies are claiming the maximum allowable deductions for environmental works under the tax laws, and provide evidence in support of such claims. Environmental legislation affecting resource industries Environmental legislation in Australia is changing rapidly and can impose massive constraints, substantial administrative costs, and considerable liability on directors, managers and the corporation. Pollution control legislation Every State and Territory of Australia has a range of pollution control legislation contained in either individual acts relating to air, water, noise and land, or embodied in a single environment protection act. Pollution control legislation provides a critical management baseline for resource industries throughout Australia, often requiring the full-time attention of an environmental manager or an environmental department. In general, it is an offence to discharge effluents into water, or emit gases into the atmosphere above prescribed limits, cause noise above a regulated level, or contaminate land without a licence. A licence determines how much of a substance can be discharged, the location, the receiving environment, the quality, and the time at which discharges can be made or noise can be caused. Planning legislation Planning legislation controls where a project is located, how it will be constructed and operated, how large it is allowed to be, and what will happen once the project is completed. Development consents or approvals will generally contain a range of conditions controlling the preparation of the site, the construction of the facility and the way it is operated throughout its expected life time. Resource projects may be regarded under legislation as scheduled or designated developments requiring special treatment during the decision-making process. Under planning legislation, it is usual for resource projects to be subject to an environmental impact assessment process. Resource legislation Resource legislation specifically covering mining and petroleum in Australia, also contains requirements regarding protection of the environment during exploration for and extraction of minerals and oil. A mining or petroleum production lease usually contains numerous conditions regarding protection of the environment and rehabilitation of the site during and after the life of the extractive process.

Jan 1, 1994

By Niles E. Grosvenor

One of the most important considerations in the efficient operation of an under¬ground mine is the haulage system. Often the determining factor between profit or loss is the quick removal of ore and waste from the working places to secondary and main-line haulage areas, and so on to the outside. Important, too, is moving supplies from the surface to the working faces so that the loading process can continue with little interruption. Men must he transported in a rapid but safe manner. It has been through the efficient use and generally the combination of mine cars, track, belt conveyors and rubber-tired haulage equipment that underground operations have been able to compete with the more popular strip or surface mining. As near-surface ore bodies are exhausted, underground haulage will play an expanding part in economically furnishing the world's needs for all types of minerals. The choice of underground haulage equipment, wherever possible, should be one that will give the smallest overall cost of ore removal during the life of the mine while meeting necessary safety requirements. The reader is referred to Sec. 12 for equipment such as scrapers and load-dump-¬haul units that perform loading as well as haulage duties. 14.1-MINE CARS AND TRACK NILES E. GROSVENOR Main-Line and Secondary Haulage-Many mines today use a combination of belt and rail haulage. Even if a- belt system is used to carry the product from the face to the surface, track is used to transport workmen and supplies. A track system, when properly installed, will provide interruption-free and safe haulage. Schrecengost 2 lists the following as major advantages of track haulage: 1. Safety in transporting men in and out of the mine in personnel cars. 2. Easy and rapid transportation of supervisory personnel. 3. A temporary shutdown occasioned by a roof fall or power failure along the haulage system will not shut down the production areas. 4. Quick availability of repair parts and supplies. 5. Large pieces of coal or rock can be handled without damage to the haulage equipment. 6. In areas where quality fluctuates noticeably, different cars may be separated out for special preparation. 7. Rock or equipment may be loaded and moved out of the mine without interference with the production or preparation of the coal. 14.1.1-MINE CARS Mine cars with steel bodies are used in all types of present-day mining. Wooden cars usually are more bulky and less resistant to wear and damage, but are more easily repaired. Regardless of the type of mine car selected, it is most practical to standardize on one type or make to simplify repairs and limit the amount of spare parts necessary to stock. Rigid-body flat-bottomed cars are simpler and usually lower than others of equal capacity. Advantages are: ease of loading because of the low sides, simplicity, cheapness and high ratio of capacity to weight. The disadvantages include the

Jan 1, 1973

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the theory of sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of along chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals, and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even lognormal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2010

By T. Wajima

"A novel carbonaceous immobilizing agent for heavy metal contaminated soil was prepared from rice straw using sulfur immersion and pyrolysis, and the lead immobilization in artificial contaminated soils using sulfur-impregnated carbonaceous material was estimated. The rice straws were cut to 1 cm pieces, and then immersed in 0.1 - 1 M K2S solution for 0 - 24 h to prepare sulfur-immersed materials. The immersed-materials were heated at 400 oC for 1 h in nitrogen gas to produce the sulfur-impregnated carbonaceous material by pyrolysis. The abilities of the product to immobilize lead from aqueous solution were examined to obtain the product with high lead immobilization ability. With increasing K2S concentration, the immobilization ability of the product for lead gradually increases and then above 0.5 M K2S those are almost constant, while 15 min is sufficient for the immersed time to obtain the product with high lead immobilization ability. The product prepared from material immersed in more than 0.5 M K2S solution for less than 15 min has a maximum immobilization ability for lead ion. The lead immobilization using the sulfur-impregnated product is sustainable due to the formation of leadhillite [Pb4SO4(CO3)2(OH)2] and anglesite [PbSO4]. The product can immobilize lead ion in various artificial lead contaminated soils. By mixing artificial lead contaminated soil with the sulfur-impregnated product, the eluted solution became neutral, and the eluted concentrations of lead ion dropped below the Japanese elution standard for soil.INTRODUCTION Soil contamination with heavy metals is a worldwide problem. Accumulation of heavy metals in soils affect soil ecology, agricultural productivity, quality of agricultural products, water resources, and serious health problems for human and animal (Raicevic, et al., 2005). In the United States, for example, approximately 63 % of the sites on the National Priority List (NPL) for the treatment of contaminated soils are contaminated by metals, and lead is the most common metal, found at 15 % of the sites. In Japan, according to a report by the Ministry of Environment, 43 % of the contaminated sites that exceed the environmental quality standards are contaminated by lead compounds. Soil contamination by lead compounds is also prevalent in other developed and developing countries where lead compounds are used extensively in industrial activities without careful contamination management. Lead is a ubiquitous heavy metal pollutant in soils due to their use widely. The primary sources of Pb contamination include industrial activities such as mining, smelting of metals, and the use of Pb-containing products such as paints, lead-acid batteries, bullets, gasoline and pesticides (Cao, et al., 2009). It can damage human nervous (especially children) and reproductive systems (ATSDR, 2007). The high concentration of Pb in the soil poses risks to human and animal health by the leaching of metals from the soil into water and the consumption of edible plants growth in the contaminated soil. Therefore, proper remediation is necessary to reduce metal availability in soil for protecting human health."

Jan 1, 2018

SOLUTION MINING Solution mining techniques present a means of extracting soluble ores, particularly such materials as salt and potash, from horizons which are not accessible by conventional mining. In the process of dissolving materials, it is evident that solution may be complete or partial. In general, the solution mining operations described in the following section relate to complete solution of the desired compound. Even though the solution of material is complete, there may be instances in which insoluble material is present to a large extent either as granular separated particles or as insoluble layers. The process required for obtaining the desired product involves access wells to reach the deposits, sufficient water supply to yield the production goals, and the development of an underground cavity. The process of solution mining, therefore, depends to a great extent on three factors: availability of a relatively pure strata or formation of salt or potash to be mined, access well or wells, and adequate control of the solutioning process so that enlargement of underground cavities can be fairly well delineated. Since halites represent the most general ores mined by this procedure, the considerations which follow are based primarily on the production of sodium or potassium chloride. The producing formations may be in the form of bedded evc~porites wherein the salt member may be some 30 to 500 ft thick or from salt domes in which great depths of salt occur. Solution mining has been carried out to depths of nearly 10,000 ft. The recovery of saturated brine from wells drilled to effect the solution-mining process leads to further processing. In many instances, the procedures are relatively simple and involve simple recrystallieation or fractional crystallieation, while in others more complex flow systems are required before a final product is obtained. The intent of this section is to provide information relative to the basic procedures for obtaining materials which are soluble in water and to acquaint the engineer with the various aspects of the overall problem which in many instances, may become quite complex and present numerous difficulties. The storage of fluids, particularly hydrocarbons, underground has proven to be a very important part of industry operations. Cavities formed in salt provide excellent storage facilities. The formation of well-defined controlled configurations of such cavities has been possible because of better understanding of the solution process, wide experience gained over nearly 30 yr, and improved technology in drilling and completing wells, surveying caverns, and the operation of numerous types of systems. Solution mining techniques will improve in the future. Many facets of the simple operation of pumping solvents and extracting valuable minerals require further study. Developments undoubtedly will occur to further the processes of mining by solution. In addition to those whose names appear in connection with the individual subjections which follow, a major role in assembling and processing the material in this section was played by Dr. D. A. Shock, Central Research, Continental Oil Co., Ponca City, Okla.

Jan 1, 1973

By S. R. Crane

One Bureau of Mines goal is to minimize the undesirable environmental impacts associated with industrial plants emitting waste gases containing S02. To help meet this goal, a regenerable flue gas desulfurization process was developed. This process, known as the citrate process, uses a buffered weak acid solution to absorb S02 from the waste gas. The absorbed S02 is reacted with H2S to precipitate elemental sulfur and regenerate the solution for recycle. The H2S feedstock for the process, if not otherwise available, may be produced by reacting two-thirds of the recovered elemental sulfur with natural gas and steam. Laboratory investigations and pilot plant operations were conducted by the Bureau to determine if H2S from the natural gas, sulfur, and steam reaction was suitable for the citrate process. The laboratory investigations, in which an H2S generator was integrated with other citrate process operations, provided a basis for design and operation of the pilot plant. The objective of the pilot plant was primarily to provide H2S for the citrate pro-cess pilot plant at the Bunker Hill Co. lead smelter in Kellogg, Idaho. The design capacity of the pilot plant was 0.4 to 1.25 tons of H2S per day. The operation demonstrated that (1) a 77-to 79-dry-volume-percent H2S product could be produced from pilot-plant product sulfur, natural gas, and steam; (2) the product R2S regenerated the SO2-loaded citrate solution; and (3) under certain conditions over 95 percent of the natural gas could be converted to H2S.

Jan 1, 1981

By R. M. Santmyers

"Quartz and silica not only occur in diversified forms in nature but find a multiplicity of uses in industry. The purpose of the present paper is to assemble brief summaries of the many widely differing industries engaged in the production and preparation of these minerals in their principal commercial forms. Due to the scope of the subject it was though advisable to divide the paper into three parts. Part I deals with the subject of quartz and silica in general. It also contains a flow sheet of silica from deposit to consumer (fig. 1). Part II covers the uses and other economic factors of quartz, quartzite, and sandstone, the varieties of silica found in consolidated form. Part III deals with sand and miscellaneous silicas such as tripoli and diatomite. A chart showing the major ramifications of these industries is presented herewith as an introduction to the more detailed discussion that follows.For a more intensive study of many branches of the quartz and silica industries the reader is referred especially to Bulletin 263 of the United States Bureau of Mines, Technology and Uses of Silica and Sand by W. M. Weigel. For annual statistics relative to silica and its products in the United States he is referred to the annual chapters of Mineral Resources of the United States, entitled ""Silica,"" ""Sand and Gravel,"" and ""Abrasives."" With respect to diatomite reference is made to Diatomite, by Paul Hatmaker, recently issued by the U. S. Bureau of Mines as Information Circular 6391. In preparing this paper the author has drawn freely from these sources as well as Marketing of Metals and Minerals, by J. E. Spurr and F. E. Wormser; Non-Metallic Minerals, Occurrence, Preparation and Utilization, by Raymond B. Ladoo; and Abrasives - Part I, Siliceous Abrasives, by V. L. Eardley-Wilmot, Report 573, Mines Brand, Department of Mines, Ottawa, 1927.Acknowledgment is also made to the Foote Mineral Co., which has published in Foote-Prints (vol. 2 of 1929 and vol. 1 of 1930), comprehensive reviews of the uses of crystal quartz in the optical industry and as piezo¬electric crystals.The various forms of silica have attracted attention from the earliest times, and the water-clear crystallized variety was known to the Greeks as""krystallos"" (clear ice), being supposed by them to have been formed from water by the intense cold of the Alps; hence the name ""crystal"" or more commonly ""rock crystal,"" applied to this variety. The name quartz is an old German word of uncertain origin used by G. Agricola in 1529.Silica or silica dioxide (Si02) either free or in combination with other elements constitutes 59.08 per cent of the lithosphere, and quartz alone represents fully 12 per cent` of all rocks. Next to the feldspar group quartz is the most abundant mineral in the earth's crust; and it appears in a greater number of varieties and modes of occurrence than any other mineral. Silica or quartz occurs in crystalline, cryptocrystalline, microcrystalline, and amorphous forms. The most common, however, is the crystalline form, which occurs as three minerals, quartz, tridymite, and crystobalite, and of these three tridymite and crystobalite are quite rare in nature."

Aug 1, 1931

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24% of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50% of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include • extraction of thick seam in ascending order with stowing ; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving ; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof, four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 3, 1987

By Russel Bohn

The purpose of this study was to evaluate the various techniques far mine roadway dust control. This evaluation included (a) the types of dust suppressants available, (b) the interaction of these products with the properties of the roadway surface, and (c) the costs and performance measures of the predominantly used dust suppressants. Over 30 products were identified having a wide range of effectiveness depending largely on the properties of the road base, subsurface, and wearing surface. The effectiveness of a dust suppressant was also found to depend on the application and maintenance procedures employed. As a result of this investigation five dust suppressants were identified s being predominant in the surface mining industry: Coherex, wetting agents, lignin sulfonate, water, and calcium chloride: An approximate cost-effectiveness analysis, limited by the lack of quantitative field performance data, showed that the five suppressants ranked in the order given above, with water being one of the least cost effective. This report also presents an analysis of applicable federal and state regulations.

Jan 1, 1981