Search Documents

By S. A. Braley

THE first commercial production of bituminous coal in the United States was in 1820, and formation of acid in the areas from which the coal was removed began at that time. Thus it is 130 years since the development of mine acid began. The coal operator has had to deal with the acid water produced in his mines, and his losses from corrosion of pumps and equipment have been tremendous. Other industries and the public have been forced to spend large amounts for their water requirements because of the acid discharge from the mines. There are many contradictions in the literature on this subject probably because of variations in the analytical procedures followed and differences in the methods of calculation and reporting. The opinions previously expressed may be summarized as follows: The production of mine acid has been looked upon as a simple chemical reaction wherein the oxygen of the air has reacted with pyrite to produce ferrous sulphate and free sulphuric acid. This reaction appears in many chemistry texts and generally has not been considered worthy of further study. Since the measurement of hydrogen ion concentration or activity was developed and expressed in terms of pH, indicator and instrumental methods for pH determination have become readily available, making it natural to think of it as a measure of acid content. Special purpose analytical methods applicable to potable waters, sewage effluents, and boiler waters, based in general upon the determination of what may be regarded as impurities, have been applied to more concentrated solutions constituting mine discharges, without reference to the fact that these specialized procedures had been developed to serve as operating guides for water-treatment plants. It has been assumed that the pounds of acid deliv- Table I. Showing pH and Titratable Acid of Varying Concentrations of Ferrous and Ferric Sulphates Ferric Ferrous ion Acldfty Ion Acidity (Fe+++) ppm CaCO3 We++) ppm CaCOa ppm PA equiv. PPm pH equiv. 11.200 1.80 30,000 11,200 3.98 20,000 5,600 2.01 15,000 5,600 4.15 10,000 2,800 2.21 7,500 2,800 4.41 5,000 1.120 2.48 3,000 1,400 4.68 2.500 560 2.60 1,500 140 5.00 250 280 2.65 750 28 5.00 50 112 2.81 300 56 3.07 150 28 3.38 75 ered by a mine was roughly a constant varying with the number of acres mined, and that the concentration of the acid in the drainage was inversely proportional to the volume of flow. Increased flow was thought to result in a dilution of the acid produced. When the Sanitary Water Board of the Commonwealth of Pennsylvania established a fellowship at Mellon Institute, the first approach to the problem was to review some of the chemical reactions involved and their relation to acid production. Since the sulphates of iron were among the principal constituents of coal-mine drainage, the first studies were based upon solutions of chemically pure ferrous and ferric sulphate. These are both neutral salts, that is, the iron and the sulphate are equivalent, but they produce acid reactions in water solution because as salts of strong acids with weak bases, they hydrolyze to form acid solutions. Solutions of each salt, of varying concentrations, were prepared and the pH, titrable acidity and iron and sulphate

Jan 1, 1952

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By C. H. Gorski

A method for preparing titanium tetrachloride is described which consists of reducing rutile with coke and chlorinating the reduced product at 200° to 500°C. The crude distillate is purified by treatment with copper powder and distillation. Recoveries, exceeding 90 pct of the titanium in the rutile, were obtained. IN recent years considerable interest in metallic titanium has been aroused because of its outstanding physical and chemical properties. The present commercial processes for preparing titanium are modifications of the Kroll1 process and consist essentially of the reduction of titanium tetrachloride with magnesium in an inert atmosphere to produce metallic titanium with magnesium chloride as a byproduct. At present,' commercial titanium tetrachloride costs $0.32 a pound, which makes the price of the included titanium $1.28 a pound. As the titanium tetrachloride must be purified further before processing into metal, its ultimate cost obviously will be higher. Consequently, one of the prime requisites for the production of lower cost titanium metal is a source of low-cost titanium tetrachloride. Recently, Knickerbocker, Gorski, Kenworthy, and Starliper3 escribed a method for preparing titanium tetrachloride from low-grade Arkansas rutile by smelting the rutile with pyrite and coke to form a titanium matte and then chlorinating the titanium matte to prepare a crude titanium tetrachloride. This process had several inherent advantages. Low-grade rutile concentrates were utilized, the chlorination temperature was relatively low (approximately 200°C), and the reaction was strongly exothermic. However, this process had several disadvantages, chief of them being the rather low recoveries of titanium tetrachloride (65 to 81 pct) and the difficulty in purifying the crude titanium tetrachloride obtained. Because of the high-titanium and low-iron con- tents of rutile as compared to ilmenite, rutile should be of greater potential value as a source of titanium tetrachloride than ilmenite. Rutile, however, is not chlorinated directly in commercial practice, because reaction temperatures above 700 °C are required, at which point chlorine attacks most of the common materials of construction. The process now in use consists of converting the titanium in rutile to the cyanonitride by high-temperature reduction in an electric furnace, and then chlorinating this compound. The disadvantages of this process are the difficulty of producing the cyanonitride, the use of high-grade rutile concentrates in the charge, and the presence of several percent of silicon tetrachloride in the finished product. It would be of considerable interest to develop a new process for the preparation of titanium tetrachloride from rutile by chlorination at 200" to 500°C. Process Development Several investigators'-' have studied the reduction of titanium dioxide with carbon in an effort to prepare titanium monoxide. Invariably, the titanium monoxide formed in this manner was not pure, as it contained titanium carbide and one or more of the lower oxides of titanium. As these lower oxides of titanium are more reactive chemically than rutile, and as it is known that titanium carbide may be chlorinated readily, a study was made of the chlorination of carbon-reduced rutile. A sample of rutile concentrates from Hot Spring County, Ark., containing 76.19 pct TiO,, 5.65 pct Fe2O3, 4.18 pct SiO2, and 2.88 pct Al2O3, was used for this investigation. The experimental procedure consisted of making an intimate mixture of —100-mesh rutile and petroleum coke, adding water and molasses as a binder to foi-m a paste, charging into a graphite crucible that was covered, except for a vent to allow the

Jan 1, 1952

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.' Previous investigators'' have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana' showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By D. J. Pye

Certain high molecular weight synthetic polymers in very dilute solutions decrease water mobility in porous media 5 to 20 times more than would be expected from the solution viscosity. This indicates that increasing water viscosity to reduce adverse mobility ratios in water floods is economically feasible in many situations. Laboratory results are consistent with accepted theory with respect to improved areal sweep, permeability distribution and displacement efficiencies as would be predicted from the solution mobility measured in the core. The laboratory results have been confirmed by field pilot floods which recovered 80 per cent and 100 per cent more oil than comparative water-flood pilots in fields containing 16 cp and 130 cp oil respectively. Economic analyses based on pilot data indicate the method to be profitable. INTRODUCTION The desirability of improving the water-oil mobility ratio in waterflood-ing operations has long been appreciated, especially for high viscosity crudes. Methods of reducing the oil viscosity by application of heat, gas resaturation and miscible drives have met with some success. Conversely, it has been generally conceded that increasing the water viscosity would also be effective, but the amount of thickening agent required to effect an appreciable increase in viscosity is discouragingly high. The use of such materials as glycerin, sugar, or glycols is completely out of the question economically, so that considerable attention has been given to the use of the much more efficient synthetic water-soluble polymers as viscosity improvers; but even these materials are not economically attractive. If increased water viscosity could be economically realized, marked improvements in areal sweep efficiency, as discussed by Caudle and Wittel and others, would be realized in field operations. Similarly, the improved mobility ratio would bring about increased recoveries by correcting permeability distribution problems as discussed by Stiles2 and Dykstra and Parsons,' and improvements in displacement efficiency would be obtained as recognized by Buckley and Leverett4 and Welge.5 LABORATORY STUDIES THE RESISTANCE EFFECT In the course of research to develop a more efficient water-soluble polymer viscosity builder, we discovered that a very few types of water-soluble polymers exhibited a most unusual and very interesting property not previously observed. Among the earliest materials showing such activity were polymers containing acry-lamide. Fig. 1 shows a typical plot of the solution viscosity vs concentration for one of these polymer solutions as determined in an Ostwald viscometer. As usual, such a plot is an approximate straight line on semi-logarithmic paper. Now, an inspection of Darcy's law, shows that a viscosity value can also be determined in a formation sample if the pressure, flow rate and permeability are known. If the core permeability is previously determined with wa- ter or brine, then the viscosity of another aqueous fluid may be determined from the equation. The viscosities so determined for glycerin (glycol or polyvinyl alcohol solutions, for example) agree with the viscometer determinations. However, in the case of the water-soluble polymer solutions in which we are interested, the viscosities measured in the formation sample depart very markedly from the viscometer values. A typical relationship for a polymer solution is also shown in Fig. 1. This unusual departure from the expected response is referred to as a resistance property of the polymer and is quantified as "resistance factor". Since the resistance factor R can best be determined in a core under study, the term has been defined on the basis of the ratio of the brine mobility to the polymer solution mobility at residual oil saturation so that:

Jan 1, 1965

By J. R. Kyte, C. C. Mattax

Previous workers have developed differential equations to describe oil displacement by water imbibition, but have not explicitly defined the relationship between recovery behavior for a single reservoir matrix block and its size. In the present work, imbibition theory is extended to show that the time required to recover a given fraction of the oil from a matrix block is proportional to the square of the distance between fractures. Using this relationship, recovery behavior for a large reservoir matrix block is predicted from an imbibition test on a small reservoir core sample. The prediction is then extended to analyze recovery behavior for fractured- matrix, water- drive reservoirs in which imbibition is the dominant oil-producing mechanism. Experimental data are presented to support the basic imbibition theory relating matrix block size, fluid viscosity level and permeability to recovery behavior. INTRODUCTION Imbibition has long been recognized as an important factor in recovering oil from water-wet, fractured-matrix reservoirs subjected to water flood or water drive. l-3 Recently, two approaches have been published which might be used to predict imbibition oil-recovery behavior for reservoir-sized matrix blocks. Graham and Richardson4 used a synthetic model to scale a single element of a fractured-matrix reservoir. lair,' on the other hand, used numerical techniques to solve the differential equations describing imbibition in linear and radial systems. This latter method requires auxiliary experimental data in the form of capillary pressure and relative permeability functions. These two approaches, i.e., synthetic models and numerical techniques, have been used to study a variety of reservoir fluid-flow problems. One pur- pose of this work is to present, with experimental verification, a third method for predicting imbibition oil recovery for large reservoir matrix blocks. This method uses scaled imbibition tests on small reservoir core samples to predict field performance. The imbibition tests are easier to perform than the capillary pressure and relative permeability tests required to apply the numerical method. Furthermore, when suitably preserved reservoir-rock samples are used, the properties of the laboratory system are the same as those of the field. This offers an important advantage over the use of synthetic models because there is usually some question as to how accurately reservoir-rock properties can be duplicated in such models. Based on the recovery behavior for a unit matrix block, an analysis is presented to predict oil recovery for a fractured, water-drive reservoir made up of many such unit blocks. In the analysis, it is assumed that the flow resistance and the volume of the reservoir fracture system are negligible compared with that of the porous matrix. These assumptions are generally consistent with observed characteristics of many fractured-matrix reservoirs, and have been employed in previous studies.2,3,6-8 further assumed that the effect of gravity on flow in the matrix blocks is negligible. On first thought, the latter assumption might appear to seriously limit application of the method. However, in a fractured reservoir, the effect of gravity on flow in a matrix block will be restricted by the height of the block. Furthermore, matrix permeabilities are often very low (10 md or less) in such reservoirs. This means that capillary or imbibition forces will be large, thus tending to minimize the relative importance of gravity. For these reasons, imbibition should be the dominant oil-recovery mechanism in many fractured-matrix, water-drive reservoirs. The predictive method presented in this report is applicable to such reservoirs. SCALING IMBIBITION THEORY The "scaling laws" applicable to the operation.

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

KNOWLEDGE of the isothermal transformation behavior and the TTT chart method of graphically summarizing such information has been of invaluable aid to the ferrous metallurgist in understanding and developing heat treatments intended to provide specific mechanical properties. It is to be expected that similar lines of study directed to titanium-base alloys will be as profitable. This paper summarizes, on conventional TTT charts, the isothermal transformation products and pertinent reaction rate data for binary alloys of titanium containing 1, 3, 5, 7, 9, and 11 pct Mo, respectively. The results so presented were derived from metal-lographic examination. Some X-ray diffraction work was done to clarify certain points of question. Ti-Mo System To the authors' k.nowledge, TTT charts have only been used to describe the reaction rates of eutectoidal decompositions. It would seem that the kinetics of decomposition of any unstable solid solution might be conveniently described in this manner. The equilibrium diagram of the Ti-Mo system' is shown in Fig. 1. The similarity with the Fe-Ni system will be recognized. Additions of molybdenum serve to stabilize the /3 phase to increasingly lower temperatures. The solubility of molybdenum in the a phase is restricted to less than 1 pct at 600°C. Under normal conditions. a homogeneous ,8 structure quenched to a, temperature in the a f & field will reject a of invariant composition. The rate at which this occurs depends on the degree of undercooling and the degree of supersaturation of /3. The structural character of the rejected phase may also be expected to be related to the undercooling. Materials and Experimental Methods A sponge titanium was used which has a nominal impurity content as reported in Table I. The nominal composition of the molybdenum used is also included. The alloys were prepared in 150 g melts by arc melting in an evacuated water-cooled copper crucible of the type reported in an earlier paper.' The pancake-type ingots were forged to 1/4x1/4 in. bars and homogenized for 24 hr at 1000°C in evacuated Vycor bulbs. Specimens Vi in. thick were cut from these bars for heat treatment. The heat treatment cycles followed an invariant procedure. The specimens were soaked at 1000°C for 20 min under a helium protective atmosphere prior to quenching into a lead bath held at a temperature corresponding to a chosen degree of undercooling. After a prescribed period of time at this temperature, the specimen was removed and water quenched. A series of specimens so treated for progressively longer periods served to establish the times for initiation and completion of the decomposition of the /3 phase at a particular temperature. Although heat treatment of unprotected specimens in a lead bath does permit surface contamination by lead diffusion, this method is necessary to insure sufficiently rapid quenching rates. As long as the bath treatments were of less than 1 hr duration. the contaminated surface was not unduly deep and could be removed without excessive grinding. Metal-lographically, the contaminated zone could be readily distinguished from the pure binary alloy. Transformation Characteristics of Ti-Mo Alloys Metallographic examination showed that a supersaturated p phase may decompose by one of two processes. Alloys containing 1 to 9 pct Mo, when quenched in water from the homogeneous /3 field,

Jan 1, 1953

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By Thomas W. Wälde

BACKGROUND Foreign investment has been a major factor in bringing about the substantial mining industries of Chile, Peru, Bolivia, Venezuela, Brasil and Guyana. But economic nationalism and sentiment against foreiqn domination of vital national industries grew in the 1960s and most major mining projects were transferred into state owner ship. Among the state mining enterprises formed were CODELCO - Chile, MINERO-PERU/ CENTRCMIN - Peru, CCMIBOL - Bolivia (in 1952), Hierro-PERU, GUY-BAU/BIDCO - Guyana, etc. New investment during that time was discouraged because it was subject to the restrictive conditions of the investment regulations of the Andean-Pact, a grouping of Chile, Bolivia, Peru, Ecuador, Venezuela and Colombia. The philisophy was that mineral resources were to be developed exclusively by national enterprises. Essential foreign inputs had to be acquired "depackaged" as separate purchases of equipment and technical assistance services. As a result of the worldwide economic recession which hit the mining industries in 1980-1982, many projects that were viable in 1970 were not developed by the new state enterprises due to lack of capital, managerial and technical abilities and due to problems with marketing. As a consequence of the long-term decline of metal prices, governments experienced difficulty in getting investment organized through national or foreign enterprises and have had to face up to the trade-offs between national control and active mineral development. A change has since taken place in governmental policies. The 1981 Peruvian mining law, the 1982 mining law of Uruguay, the 1979/1980 mineral promotion laws of Argentina, all witness the gradual shifting of emphasis from restriction to promotion. The investment rules of the Andean Pact have been progressively softened through national regulation and today are more or less irrelevant. Nationalizations and forced renegotiations have not occurred in the last few years. Countries have gone to great lengths (without much success) to re-attract foreign investment on terms that accommodate the political sensitivities of the South American countries and the practical requirements of investors and financiers. For this analysis, three contracts have been selected which reflect this accommodation in three South American countries, where miner a1 production plays a major role in the national economy. These con tracts reflect both the attitudes and traditions of the individual countries, but also mark the shift in mineral investment policies that has taken place. EL INDIO AGREEMENT The 1977 investment agreement between Chile and St. Joe Minerals marked a dramatic relationship between Chile and foreign mining investor s. In Chile, mining of copper has played a major role in the country's history. Large scale copper mining was initiated and developed by Kennecott and Anaconda. The nationalization of these two companies under the Allende government in July 1971 started a wave of nationalizations of foreign-held mining and petroleum operations since then in many parts of the world. The military government supported the new Chilean state mining companies ((30DELCO and ENMI) , but it also attempted to accelerate mineral development by prom ting foreign private investment, thus reversing the nationalistic policies followed by the Allende and the preceding Frei government. The new policy by the military government is expressed in Decreto-Ley 600 (1974) which governs foreign investment in Chile. Decreto-Ley 600 is

Jan 1, 1985

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

By D. A. Flanagan, B. L. Landrum, P. B. Crawford, B. C. Norwood

Herern is described a heat conduction model which has been developed to predict the pressure distribution within a reservoir being subjected to rrnsteady-state depletion. Although potentiometric models have been widely used to study reservoir pressure distribution, their application is limited to the study of steady-state cases. Electrical analyzers may be used to study unsteady-state phenomena, but their application and simulation have certain limitations. Much of the now accepted theory of unsteady-state fluid flow in porous media has evolved from previous heat conduction knowledge. An analogy between the flow of fluid in an unsymmetrical reservoir and con-duct ion of heat in a similarly shaped unsymmetrical metal plate is made to show adaptability of the hear conduction principle to transient reservoir cases. A description of the model and necessary instrumenrarion is included. Data show influence of well location on pressure distribution during unsteady-state deple[ion. Application of results is made to a hypothetical reservoir and to a reservoir located in an irregular aquifer. INTRODUCTION Development of methods for predicting behavior of petroleum reservoirs has resulted partially from adaptation of electrical and thermal flow concepts to the flow of fluids through porous media. Extensive investigation of electrical and thermal flow problems has resulted in mathematical solutions applicable to many reservoir problems. The relative ease of measuring electrical flow has brought wide acceptance of the use of the potentiometric model to study certain field problems. Potentiometric models are restricted to the study of steady-state conditions because of the instantaneous response of electrical flow to changes in the applied potential. The electrical reservoir analyzer has been one of our most useful instruments for studying certain phases of unsteady-state behavior1. Other than approximation techniques, no method exists for determining pressure distribution in an irregular reservoir during primary depletion. Heat flow, like fluid flow, is inherently transient. The model described here was developed to use this transient nature of heat flow, measurable in the laboratory, to simulate transient flow of fluids in the porous medium of the reservoir above the bubble point. A metal plate shaped like the reservoir to be studied was heated by a "well" source. Temperature increase in the plate is analogous to pressure decline in the field if the field is being depleted, or pressure increase if fluid is being injected. This study is intended to determine the feasibility of using the transient nature of the heat flow to study the transient behavior of fluid flow. It is hoped that this new technique will aid in the understanding of one of the more complex phases of reservoir engineering. THE FLUID FLOW-HEAT CONDUCTION ANALOGY The similarity of the equations which describe the flow of fluids through a porous medium and the conduction of heat through a solid is well known2. Rate of flow of fluids is given by Darcy's law3. while the rate of flow of heat is given by Fourier', (I,, - KA 4T........(2) Combining Eq. 1 with the equation of continuity for a compressible liquid", i.e.,results in Expressing y in terms of the compressibility, i.e., pr = peey ,..........(5) and by expanding the exponential and neglecting higher orders of cp one can obtain

By B. H. Caudle, A. R. Khan

The oil production performance of thin-oil-column type reservoirs producing entirely by natural water drive are discussed in this paper. The dimensionless production histories were obtained in a series of scaled porous-medium laboratory-model tests under varying effects of rate of production, mobility ratio across moving boundary, ratio of oil- and water-sand thickness and mobility ratio across fixed boundary including the effects of different residual oil saturations in the water-invaded regions. This scaled-model study of thin oil columns indicated that greater recovery of oil results for lower values of the following: rate of production, mobility ratio across the moving boundary, water-sand thickness relative to the oil-sand thickness, and mobility ratio across the fixed boundary or residual oil saturation in the water-invaded region of oil sand The results of the study are given as dimensionless production history plots which may be used to predict the performance of the field they represent. INTRODUCTION Oil fields producing under natural water drive can be classified into two major groups: (1) an "edge-water drive" reservoir group in which the water is encroaching from the reservoir periphery, and (2) the group of reservoirs in which the oil-sand is entirely underlain by an aquifer. Reservoirs in the second group are further subclassified as "bottom-water drive" reservoirs and "thin-oil-column" reservoirs. The latter reservoirs are characterized by their relatively equal oil- and water-sand thicknesses and by having both the oil and water zone relatively thin. When oil is produced from a water-drive reservoir by a partially penetrating well, water breaks through sooner or later before all of the displace-able oil is recovered. Many analyses of this general situation have been made with varying degrees of realism in their approaches, both theoretical and experimental5.6 in nature. Pertaining to the scaled laboratory model studies of natural water drives using porous media, detailed investigations have been made by Henley, et al.7 on bottom-water drive and by Caudle8 on edge-water drive reservoirs. No laboratory model studies, however, have been made to investigate the performance characteristics of thin-oil-column reservoirs. This paper presents the results of a study on scaled models of thin-oil-column reservoirs, operated under varying conditions corresponding to the actual field practices. SCALING PARAMETERS The object of scaling is to produce a one-to-one relationship between physical and dynamic parameters of the model -and prototype. The most comprehensive treatment of scaling techniques for oil reservoirs is given by Geertsma, et a1.,9 which covers two methods for arriving at dimensionless groups for scaling. Table 1 lists the scaling parameters suitable for creating kinematic and dynamic similarities between the model and the prototype in the variables considered for the thin-oil-column reservoirs. In order to achieve similarity it is essential that the dimensionless groups listed in Table 1 have equal values in the model and the protorype simulated. Since it has been established that the role of interfacial forces is neglible in gross fluid movement in a reservoir no attempt was made to scale capillary forces- Although there are reports describing Scaling criteria for these forces,10,ll consideration of the necessary but restrictive conditions for

Jan 1, 1970

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a&apos; range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.&apos;

Jan 1, 1955

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"&apos;. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By F. Forscher

Pronounced porosity, decreasing with distance from the fracture surface, is found in the necked region of tensile specimens tested at room temperature or liquid nitrogen temperature. A hydrogen solution treatment followed by a quench prevents pore formation in tests at —196°C, but has little effect on tests made at room temperature. Reduction of area values at —196°C are strikingly improved by the same treatment, but show no improvement in room temperature tests. The experimental results support the hypothesis that strain-induced porosity results with hydride initially present or, in material containing less than 50 ppm H, with hydride precipitated by strain aging. ZIRCONIUM&apos;S advent as an engineering material in nuclear reactor construction has brought forth many investigations concerned with the properties of this metal and its alloys. Some attention has been given to the ductility of the metal.1, 2 Particularly, the effect of hydrogen on the impact strength was noted," indicating a pronounced dependence of ductility on the hydrogen content and its distribution in the metal. Micro graphic:&apos; and X-ray diffraction studies&apos; have shown that a precipitated hydride phase causes embrittlement in zirconium,&apos; which implies a distinctly different mechanism from that causing hydrogen embrittlement in steels."-&apos; In the latter case, it is assumed that atomic hydrogen diffuses to rifts, where it forms molecular hydrogen under such internal pressures that it causes the rifts to enlarge, leading to fracture. Thermo-dynamic studies of the Zr-H system8, 9 also indicate that the internal pressure of molecular hydrogen would be too low to cause any damage to the zirconium at room temperature, and the formation of a zirconium hydride (d phase) is favored." It is noteworthy that this phase has a face-centered-cubic structure and nearly 18 pet larger molar volume than close-packed-hexagonal a-zlrconlum&apos; Other features of the ductility of zirconium are the absence of a typical cup-cone failure upon tensile testing, a pronounced strain-induced porosity in the necked region of a tensile bar, Fig 1, and the associated spongy appearance of the fracture surface A tremendous improvement in ductility at liquid nitrogen temperature can be observed following a heat treatment that retains the commonly present quan- tities (10 to 50 ppm) of hydrogen in solution. Such tests show a typical cup-cone failure and the absence of strain-induced porosity, Fig. 2. The present paper reports results of an investigation into the causes of strain-induced porosity in zirconium. Room temperature tensile fractures of mild steel, aluminum, and titanium have also been examined for strain-induced porosity. In each case porosity could be detected, but the amount was orders of magnitude less than was found in zirconium. Of the three metals, titanium showed the strongest effect. Material, Specimens, and Preparation The greater part of this investigation was done on Westinghouse crystal bar zirconium, are-melted, forged, and hot-rolled. Chemical analyses of the hot-rolled plates are given in Table I, along with those of the Foote crystal bar zirconium used in this work. The specimens were machined from the hot-rolled plate (1550°F) of 1/2 in. thickness and subsequently heat-treated according to one of the treatments shown in Table IS. All specimens were machined round, the longitudinal axis in the rolling direction, with a gage

Jan 1, 1957