Search Documents

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ' pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron' and molybdenum.' The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,' containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln' wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,' mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

By Michael G. Nelson, Amy Richins, Ashley Hodgson, W. Pratt Rogers

"Sociotechnical systems are everywhere in the modern industrial world. Sociotechnical systems describe how humans interact with technology throughout a variety of processes. These systems are prevalent in modern industrial settings, such as operating mines. Safety and health management systems (SHMSs) are complex sociotechnical structures designed with the aim of managing and reducing occupational risk. U.S. mining companies are voluntarily adopting SHMSs to supplement regulatory safety compliance efforts. Like all complex sociotechnical systems there are a wide variety of approaches and adoption philosophies around a SHMS. Many SHMSs suffer from high levels of redundancies, which manifest themselves in diverse ways: duplicate processes, forms, permits, and tracking mechanisms. These redundancies have severe impacts on the overall system and absorb critical culture and leadership “energy”. A recent study initiated by the University of Utah and sponsored by the Alpha Foundation is investigating the effectiveness of SHMSs across 15 different U.S. mining sites. A large amount of data has been captured to help characterize elements of SHMSs and correlate their impacts on safety outcomes. Many variables were assessed in the study. Those of importance to this paper are the variables describing the robustness of the sociotechnical aspects of the SHMS. Two such variables are the overall integration of the SHMS within the whole system and how data is managed. Data management in this context deals with the approach to capturing, analyzing, and acting on data within the system. As well, systems are integrated around controlled, data-sharing mechanisms. It has been found that wide variety of approaches has been taken to integrate the SHMS within the governing management philosophy at a given site. A series of case studies is presented that develop some specific best practices for proper data management and integration of SHMSs.Introduction and Project Background Managing occupational health and safety can be done in many different ways, and with many different approaches, but is often based on the host country’s regulatory and industrial culture. However, many companies have extended their effort beyond the regulatory requirements of their host nation and have implemented Safety and Health Management Systems. The goal of these efforts is to reduce and eliminate occupational risk. Many health and safety practitioners have a hard time justifying various elements of health and safety management. There is a lack of institutional knowledge that measures and assesses the effectiveness of these Safety and Health Management System (SHMS) elements. To better understand the effectiveness of SHMSs the Alpha Foundation has funded a research project with the University of Utah. The title of the project is “Characterization and Effectiveness of Safety and Health Management Systems in the U.S. Mining Industry.” The research team will assess the SHMSs of 15 United States mine sites. The outcome of the project will be a method to characterize the strength of the SHMS elements, assess a culture and leadership index, and finally establish correlations between elemental risk and safety outcomes. The study is currently in progress. However, many important outcomes have already been observed, particularly on the data management practices within an SHMS."

Jan 1, 2017

By E. Teghtsoonian, K. G. Davis

THE preparation of cobalt crystals offers problems: on cooling through 400°C a phase transformation takes place whereby the structure changes from face-centered cubic to the low temperature close-packed hexagonal form. There are a few references in the literature which describe the preparation of cobalt crystals for magnetic work1,&apos; where melt-solidification methods were used. Reasons will be given why such methods were found unsuitable for our purposes. The following techniques were tried: 1) Solid state methods. Any mechanical shaping of tensile specimens would lead to uncertainty with regard to residual strains. With this in mind, following Kaa, strain-anneal and grain growth techniques were extensively investigated. In no Case were useful single crystals obtained. The transformation boundaries, which are crystallographically similar to twin boundaries, are probably extremely stable and inhibit the grain growth. 2) Growth from the melt. Normal melt-solidification methods were tried, using recrystallised alumina crucibles, and also a osoft moldo technique in which cobalt rod was packed in alumina powder. Trouble was encountered with gas evolution on solidification of the melt, giving porosity. Some adhesion of cobalt to the alumina also took place. Only a small proportion of the runs gave single crystals. 3) Zone-refining. Much the best results have been obtained using an electron-beam floating zone refiner. The refiner, based on a design by Calverly et Al .5 had a single-turn tungsten filament. It was operated at 600 v with an emission current around 45 ma. Commercial cobalt rod 1/8 in. in diam was given one pass at a rate of zone travel normally 25 cm per hr, under a vacuum approximately 10-5mm of Hg. Over 50 pct of the runs gave long sections of single crystal. Crystals up to 2o Cm long with good uniformity of cross section and straightness have been grown in this way. Increase in the length of the molten zone resulted in higher single-crystal yields, but control of zone stability was reduced. Sub-boundaries in the zoned crystals were few, and Laue X-ray spots were sharp. The success of the method is believed to lie in two factors, namely i) the absence of crucible restraints during the transformation, and ii) extreme axiality of heat flow during cooling. The axes of the zoned crystals were clustered around the [ 1010] pole, the pole of the basal plane being at least 60 deg from the specimen axis. Crystals grown at lower rates of zone travel showed the same orientation range, Fig. 1. This orientation is similar to that for other hexagonal metals grown from the melt, which is a little surprising when the mode of formation of the hexagonal phase is considered. The preferred orientation is probably caused by anisotropy of heat conduction, i.e., that crystal which can most effectively conduct heat away from the transformation interface will be favored. Fig. 2 shows the area on a standard cubic stereo-gram in which there are no poles more than 60 deg from one of the four < 111> directions. This area

Jan 1, 1962

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By C. S. Touchard, F. Bourgeois, L. Cassayre, Julcour-Lebigue C.

Developing a hydrometallurgical process that can overcome the refractory nature of chalcopyrite (CuFeS2) to leaching still eludes the minerals industry, despite major research efforts spanning decades. The several leaching experiments of this ore in sulfuric acid tend toward the same conclusion that the precipitation of elemental sulfur or iron containing species are the main dissolution inhibitors. Describing both the electrolyte composition and the various solid phases in equilibrium for the Fe-H2SO4-H2O system is essential to overcome this issue and to find an operating window. According to the thermodynamic models and to the thermodynamic data, we demonstrate, in this study, the need to use the Specific ion Interactive Theory (SIT) model to describe complex electrolytic systems through a limited number of parameters. Hence, the binary interactions for our case study have to be defined and estimated. This work develops a methodology to determine these parameters of the SIT model up to 90°C and an acid concentration of 1 mol/kg from published data for H2SO4-H2O and Fe(II)-H2SO4-H2O sub-systems or from new experimental data for the Fe(III)-H2SO4-H2O one. This method will eventually be applied to copper systems to lead to a thermodynamic description of the complete CuFeS2-H2SO4-H2O system. INTRODUCTION A leaching process consists in the dissolution of a solid phase into an aqueous medium in order to extract compounds of interest. It is a key step in the hydrometallurgical processes used in the primary production and recycling of metal components. One of the main leaching issues is the formation of passivating layers on the surface of solid particles, whose consequence is a partial or total hindrance of the dissolution. The leaching of chalcopyrite (CuFeS2) in sulfuric acid is a prime example. No industrial solution for the atmospheric pressure leaching of this ore has been developed to date because of passivation phenomena caused by the formation of elemental sulfur or iron-containing precipitates on the surface of the particles (Li, Kawashima, Li, Chandra, & Gerson, 2013). In the 1970s, the Pourbaix diagrams established for the Cu-Fe-S-H2O system at 25°C for low concentrated solutions (Garrels & Christ, 1965; Peters, 1976) agreed that copper and iron are fully dissolved at high potential and in acidic medium (pH < 4). However, they neglected the many stable solid phases that can form in these conditions. In addition, the Pourbaix diagrams of chalcopyrite in water, calculated with two recent databases (FactPS and Thermoddem 2017) associated to FactSage and PhreeqC softwares respectively, show large discrepancies at 75°C (Figure 1). Indeed, at high potential, FactSage predicts the formation of goethite FeOOH at a pH value of 1, while PhreeqC predicts the formation of jarosite (H3O)[Fe3(SO4)2(OH)6] for pH greater than 2.5.

Jan 1, 2019

By B, G Strobos, J P. Maree, N Smit

In mining and processing operations where minerals, high in pyrite and low in calcite/dolomite are processed, acid is generated, which needs to be neutralised. Ticor at Empangeni in South Africa (SA) produces rutile (TiO2), leucoxene (TiO2 plus iron compounds), titanium (Ti), zircon (Zi) and ilmenite (TiO2 plus iron compounds). Neutralisation is required in the processing plant where acid is leached into the wash water. This water needs to be treated to a quality suitable for re-use in the metallurgical process or to a higher quality to make it suitable for discharge into the Empangeni sewage system (SA). For re-use the water needs to be neutral and under-saturated with respect to gypsum while for discharge into the sewage system the sulfate concentration needs to be reduced to less than 500 mg/L (as SO4). Acid mine water is generally neutralised with lime. Disadvantages associated with lime are the costs and maintenance of the slaking equipment as well as hazards, associated with handling of the alkali. The cost of powdered limestone (CaCO3) in South Africa, a by-product, is 50 - 60 per cent cheaper than lime. A technology has been developed where limestone is used for neutralisation of acid mine water instead of lime. This development includes: Limestone handling and dosing system. A novel, robust system has been developed where waste CaCO3 from the paper industry is slurried to a constant density. A full-scale plant was constructed to evaluate its performance (Figure 4). The dosing system consists of an inclined slab onto which the limestone is stored and from where it is slurried into a make-up tank. The density of the slurry in the make-up tank is controlled via a loadcell that measures the weight of the tank (operated at constant volume) and activates/deactivates the spray of the recycle slurry onto the slab. Integrated limestone neutralisation/lime treatment process. In this process powdered CaCO3 is used for neutralisation and partial sulfate removal of acid leached from the coal washing plant. The sulfate concentration can be further reduced to below the saturation level of gypsum (ie 1200 mg/L) through gypsum crystallisation by means of lime treatment, resulting in metal precipitation (eg Fe3+ and Al3+). CO2- treatment for CaCO3 precipitation. The pH of the lime treated water can be adjusted to pH levels of 8.5 and lower using CO2. The CO2, generated during limestone neutralisation (Equation 2), can be captured and used in this stage of the process. The first two stages (limestone- and lime neutralisation) of this technology have been implemented on full-scale at Ticor to treat the effluent of the process. The constructed plant is 80 m3/hr and differs from coal processing plants by way of not containing Fe(II) and Fe(III) in the water. The CO2-treatment stage (Stage 3) will soon be implemented at IHM as part of a program to optimise the technology for maximum benefits.

Jan 1, 2003

By J. Burrows

The Chamber of Mines of South Africa is an association of major mining corporations, gold mines, coal mines, diamond mines and other metalliferous mines. It looks after those interests of its members which can best be handled on a co-operative basis. The Chamber&apos;s activities include the engagement of labour; the negotiations of all labour matters, including minimum wage rates, with recognised trade unions and associations; the carrying out of advanced technological research; representing the industry in dealings with the government and the administration of miners&apos; training colleges and rescue training stations. Subsidiary companies of the Chamber handle matters such as the refining of gold and other metals; the processing and marketing of uranium and the marketing of Krugerrands. The thirty-two gold mines members of the Chamber of Mines of South Africa produce approximately 694 tons of gold per annum. To achieve this they employ 430000 persons and break about 8400 kilotons of rock per month. The working revenue is approximately 4 225 million US dollars per annum and the annual working profit is approximately 2 050 million US dollars. The electric power consumed by the gold mining industry is 1650 MW, about 20% of the total power produced in South Africa, and the annual costs of this power is approximately 200 million US dollars per annum. It is estimated that about 25% of this power is used for ventilation and refrigeration appliances. Thus the annual power costs for ventilation and refrigeration is approximately 50 million US dollars. The gold bearing reef is a narrow tabular deposit situated at varying depths throughout the gold fields. The weighted mean rock breaking depths and, virgin rock temperatures range from 1 700 - 9 000 ft (520 - 2 740 m) and 68 - 113°F (20 - 45°C) respectively. The maximum virgin rock temperature at which mining currently takes place is 130°F (54.5 C). Obviously at such depths and temperatures and with such a large labour force the provision of an acceptable environment is critical and to achieve this 59 000 000 cfm (28 000 m3/s) of air is downcasted during the main shift and 122500 tons (430 MW) of refrigeration are provided. Legislation in South Africa requires that on metalliferous mines when more than 1000 persons are employed underground during any one shift the manager shall appoint one or more ventilation officers. The legal responsibilities of the ventilation officers are concerned mainly with the measurement and control of dust. In practice, this is not the main part of their work and ventilation personnel perform many other duties such as measuring and controlling the distribution of air, checking the performance of fans and cooling plants, planning air and refrigeration requirements and, more recently, measuring and controlling noise and illumination levels. Ventilation personnel are specialists who provide management with advice on all matters relating to the mine environment. At the present time there are 506 persons engaged as ventilation personnel in gold mines and a further 1744 persons are employed in gold mine ventilation departments in a non-technical capacity, for example as construction workers, filter cleaners, fire patrollers, etc.

Jan 1, 1980

By B. D. Cullity, O. P. Puri

The magnetostrictia of nickel after increasing amounts of plastic elongation was measured at field strengths up to 1500 oe. In addition, the residual stress was measured by means of X-ray line shifts. The observed decrease in magnetostriction following plastic strain is shown to be associated with residual compressive stress. If a metal bar, whose longitudinal axis is taken as the x direction, is plastically elongated in the x direction and then unloaded, X-ray diffraction measurements will indicate the presence of a residual compressive macrostress 0%. However, stress measurement by means of mechanical relaxation does not reveal any macrostress. In a previous paper1 the fictitious macrostress indicated by X-rays was ascribed to a particular distribution of micro-stress, namely, one in which the bulk of the material was stressed more or less uniformly in compression and a very small portion in tension. It was shown that this distribution would account for Neurath&apos;s measurements2 of magnetic losses in silicon steel, because of the effect of residual stress on magnetostriction. The present paper is concerned directly with magnetostriction, in nickel, and with the effect on magnetostriction of the residual stress created by plastic elongation. The residual stress was determined by measurements of X-ray line shifts. MATERIAL AND METHODS Commercially pure "A" nickel was investigated. Its nominal composition, in weight percent, is 99.4 Ni + Co, 0.2 Mn, 0.15 Fe, 0.1 Cu, 0.1 C, 0.05 Si, and 0.005 S. Magnetostriction was measured by means of SR-4 electrical-resistance strain gages mounted on specimens 1/4 in. sq and 8 in. long. Magnetic fields up to about 1500 ce were provided by a multilayer, non-cooled solenoid. A considerable amount of heat was developed at the higher field strengths, and, to avoid errors due to changes in the specimen temperature, the following procedure was adopted. Each measurement of the magnetostriction X at a particular field strength H was preceded by demagnetization and an adjustment of the strain indicator to zero; the field H was then quickly switched on and the strain read immediately. Curves of ? vs H were flat for field strengths above about 750 oe for all specimens, and this constant value of X was accordingly taken as the saturation magnetostriction ?s The X-ray measurements of residual stress were made with a Norelco diffractometer on specimens cut from flat bars 1 1/4 in. wide, 1/8 in. thick, and 12 in. long. These measurements were confined to lattice planes parallel to the surface of the specimen. Two reflections were studied: the 311 CrKß line at 28 = 157 deg, and the 420 CuKal line at 28 = 155 deg. The line centers were determined by fitting a parabola to the peak of the line, as suggested by Ogilvie3 and as modified by Koistinen and Marburger.4 The CuKa doublet from the plastically elongated specimens was first resolved by the Rachinger method5. All X-ray measurements were made by counting at fixed angular positions. RESULTS The results of the magnetostriction measurements are shown in Fig. 1 and Table 1. The magnitude of

Jan 1, 1963

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By N. L. Muench, J. S. Osba

Research conducted previously has demonstrated that spectral analysis of gamma radiation from the naturally radioactive elements present in earth materials permits detervination of the relative concentrations of these elements. This research suggested that spectral analysis of gamma radiation resulting from neutron bombardment of elements not nor-mally radioactive might serve to identify these non-radioactive elements, and might permit their quantitative determination. To investigate this possibility, laboratory experiments were conducted in which various earth materials were subjected to bombardment by neutrons from a polonium-beryllium source, and in which the spectra of the resultant gamma radiation were analyzed. The geometry of the lab-ortory system was designed to simulate wellbore conditions. The laboratory work demonstrated that some elements not only can be identified with relative ease, but also can be determined quantitatively. This finding indicates that the use of an intense source of more energetic neutrons may lead to the identification and measurement of additional elements of interest by means of induced nuclear reactions. INTRODUCTION In recent years the applications of nuclear physics to the producing branch of the petroleum industry have become increasingly numerous. One significant development, an outgrowth of nuclear science which is of potential importance in well logging, has been the analysis of gamma-ray spectra of naturally radioactive elements in earth strata. The work of Brannon and Osoba1 has demonstrated that presently available equipment and techniques may be used to determine the relative concentration of thorium, potassium, and uranium in underground strata by means of gamma-ray spectral analysis. Success of the research on spectral analysis of naturally radioactive elements suggested that spectral analysis of induced radioactivity might serve to identify, and perhaps measure quantitatively, those elements which normally are not radioactive, but which become radioactive on neutron bombardment. It was to investigate this possibility that the research described in the following sections was undertaken. THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bom- barded with neutrons, emits gamma rays of energies characteristic of that element. Therefore, in theory, an element may be identified by analysis of the energy spectrum of the neutron-induced gamma radiation. If a neutron impinges upon the nucleus of an atom, any one of several reactions may occur. For identification of elements in earth formations the more important are listed below: 1. The neutron may be elastically scattered, as in a collision between two billiard balls. In this case the total kinetic energy is conserved, and no nuclear radiation is emitted. 2. The neutron may be inelast-ically scattered, as in a collision between two automobiles in which case the total kinetic energy is not conserved. The lost kinetic energy reappears in the form of gamma radiation. 3. The neutron may be captured, in which case the neutron becomes a part of the target nucleus, and a gamma ray is emitted. For example, if the target nucleus is H1, the pro-duced nucleus will be H3, and gamma radiation of a particular energy will be emitted. 4. The neutron may produce nuclear fission, or may enter into miscellaneous reactions which result in the emission of

Jan 1, 1958

By S. A. Herres, A. R. Elsea

Temper brittleness refers to the loss in the notched-bar impact resistance encountered in most medium- or low-alloy steels when they are tempered within the temperature range of 700 to ll00°F or slowly cooled from a higher tempering temperature. Temper brittleness is important because it impairs the service properties of otherwise suitable steels over the range of hardnesses obtained at medium tempering temperatures and because it is impractical to cool pieces of large section rapidly enough from higher tempering temperatures to prevent temper brittleness. The problem of temper brittleness has always been closely associated with ordnance manufacture because armor plate and gun steels require good shock resistance and are often heat treated in heavy section. However, it is now realized that many brittle failures in structural alloy steel parts are attributable to temper brittleness, and there is little question that it contributes to the low impact resistance of alloy steels used in the hot-rolled or normalized condition which are slowly cooled from the hot-rolling or normalizing temperature. Recently Hollomonl has presented a comprehensive summary of the literature on the subject and an excellent description of the manner in which temper brittleness affects the notched-bar impact resistance and other mechanical properties of steel. Carpenter and Robertson2 have given a good analysis of the probable mechanism of temper brittleness, which is similar in many respects to the precipitation-hardening phenomenon. Fig 1 is their diagram illustrating the response to tempering of a susceptible steel. Three changes are recognized as the temperature of tempering a previously quenched steel is raised: (1) pre- cipitation occurs more rapidly and to a greater extent and the notched-bar impact value falls to a minimum; (2) coalescence of the precipitated particles begins to be effective and the impact values for both rapidly cooled and slowly cooled specimens increase; (3) the precipitate goes back into solution at higher tempering temperatures and the impact values of specimens cooled rapidly enough to retain the solution increase, while reprecipitation occurs in slowly cooled specimens and their impact values decrease again. No change must proceed to completion before the following one begins and there is overlapping in temperature ranges. Although there have been a large number of experimental investigations of temper brittleness, insufficient evidence has been accumulated to permit definite identification of the precipitate wnich causes temper brittleness nor have the specific effects on it of various alloy elements and impurities in steel been definitely established. This lack of evidence is largely a result of the lack of a suitable measure for temper brittleness. Temper brittleness is evidenced by an increase in the temperature of brittle failure of notched-bar impact specimens, but most of the data are in the form of an arbitrary susceptibility ratio of the room-temperature impact value for specimens quenched from a high tempering temper to that of similar specimens furnace cooled from the temper. It is obvious that this numerical ratio is dependent upon the type of specimen used and the specific conditions of testing rather than the characteristics of the steel. In general, manganese, chromium, and nickel alloy steels are most susceptible to temper brittleness and molybdenum has heen used to decrease

Jan 1, 1950

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn&apos; showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.&apos; , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.&apos;

Jan 1, 1956

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930&apos;s were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,&apos; so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By E. K. C. Chanda

The best use of available reserves to give good metal recoveries relies on short term mine production scheduling.-The aim is usually to produce a plan to guide mining in specific areas that will enable mine operations to deliver the budgeted tonnes and grade to the mill and keep within the long range mine plan. Thus, short term production scheduling is an important aspect of the open pit mine planning function. Since the 60&apos;s increased attention has been paid to effective production scheduling as a means of improving the economic viability of existing mines. Hence, mine scheduling scheduling systems have been evolving rapidly during the last two decades. These systems include manual techniques, computer based simulation, mathematical programming and more recently Computer Aided Design (CAD). Some general drawbacks of the current scheduling systems are that firstly, the costs of acquiring and using them are not at all insignificant especially for small to medium sized pits. Secondly, there is an inherent trial-and-error aspect in these systems. Thirdly, they tend to be suited for specific orebody geometries, hence lacking the necessary generality. For instance, the use of computer programs for planning open pits to mine stratiform orebodies raises problems which are not usually met when massive orebodies are considered. There for, a need exists to develop simpler but effective short term pit scheduling procedures suitable for stratiform type orebodies, considering their geometry and geology. This paper describes a PC- based model designed to assist the planning engineer in optimizing the short term production schedule in open pit mines with stratiform orebodies. The model is based on a combination of linear goal programming and deterministic mining simulation. The orebody model is made up of ore and waste mining regions where winning and and/or stripping are taking place. These shovel regions form the basic planning elements in the model. This approach does not require the laborious preparation and use of a regular block model. The computer program consists of main modules: (i) Data capture - processes the raw data into the required format for mine planning. (ii) Precedence mining constraints - checks the status of each shovel .region at the beginning of a given scheduling period with regard to geometrical mining constraints such as undercutting. (ii) LP- Optimization - provides an optimal selection of ore shovel regions which do not violet geometrical constraints for mining in the period, the objective, being to maximize the contained metal equivalent in the blended R-O-M ore and at the same time to minimize deviations in grade and tonnage from the call values. (iv) Post LP-Simulation - enables the user to smooth out the LP solution in order to adjust it to a practically executable plan and simulates mining of ore and waste for the period. Shovel allocation to selected ore and waste shovel regions, unit operations and depletion of reserves are executed in this module. Preliminary testing of the model for monthly production scheduling using data from Nchanga OPen Pit on the Zambian Copperbelt indicates that it can be a useful planning tool and gives acceptable results.

Jan 1, 1992

By E. H. Citron

CLEANING fine coal in jigs is not new in Europe, where the feldspar jig is being used almost exclusively for this purpose. A feldspar jig operates with an artificial bed made up generally of feldspar or other hard rock material. Dimensions and specific gravity of this material must be of suitable values for good bedding qualities. For good efficiency, the size should range between 1x2 in. and 2x2x½ in. thick. The disadvantage of an artificial bed is that it is not mobile and must be replaced every so often with new material to obtain good cleavage characteristics. A semi-mobile bed has been developed to retain only a part of the feldspar on the sieve screen— the other part is drawn off with the refuse material, from which it is reclaimed and returned to the jig feed. Recirculating this feldspar rock offers definite advantages. However, in time it will lose its original shape because of wear, and new bed material must be added to the jig feed. The latest feldspar jigs arc generally air-pulsated, Baum-type jigs, although more than 70 pct of the feldspar jigs operating in Continental Europe are still of the piston type. These jigs are very popular in Europe, but they do require a great deal of time and attention. New Theory to Eliminate Artificial Bedding: At the preparation plants of Pittsburg & Midway Coal Mining Co. it has always been the contention that a small piston-type jig could be developed to clean fine 1/4x0-in. coal down to 28 to 60 mesh efficiently by obtaining and admitting bedding material from the present plant refuse circuit to the jig feed. This eliminates use of artificial bedding materials. The jig should incorporate these essential adjustable features as follows: Adjustable Sieve Screen A screen that can be raised and lowered to increase or decrease washing compartment depth. The sieve screen also can be set on an incline level, or decline. Adjustable Plunger Eccentric Length of stroke can be adjusted to increase or decrease pulsion and suction. Variable Plunger Speed Variable speed reducer for decreasing and increasing the number of strokes per minute. Water Distribution Adjustable baffle plate separating the plunger and sieve compartment so the water can be distributed uniformly over the entire sieve screen area. Refuse Ejector Special unique rubber-type refuse ejector gate operated by air and electrically controlled (as a conventional jig). Automatic Control Conventional float that measures the specific gravity of the coal-water refuse medium in the jig is of the submerged type. The float is mounted on a vertical stem held in position by two parallel arms. A movable weight regulates the effective specific gravity of the float. The float stem can be raised and lowered, having a graduated scale to indicate the depth of bed for the setting of the float. Hutch Drawoff Hutch material is drawn from the cell compartment to the elevator compartment by gravity. The first one-cell experimental jig incorporating all these features was built in January 1955 by Ore

Jan 1, 1959

By P. Lelong, P. Lacombe, J. Herenguel

IN previous studies on the effect of orientation on the rate of anodic oxidation of A1-3 pct Mg mono-crystals of high purity, certain anomalies were observed on the cold-worked metal. These anomalies were shown to correspond to regions of changed orientation within the grains resulting from plastic deformation.&apos; In fact, they are deformation bands revealed by differences in rate of oxidation and produced by more or less continuous bending of the lattice about a [Ill] axis common to the original crystal and the band.2,3 Preliminary observations made after relatively large degrees of cold working revealed an approximate twin relationship between the bands and the surrounding crystal. Fig. 1 shows the etch figures formed on such a band and on the original monocrystal after a 67 pct rolling reduction. It is evidently not a true twinning, since there is a broad transition zone between the two systems, however the two extreme orientations are nearly in a twin relationship. It was decided to investigate these preliminary observations by progressive rolling-reductions on monocrystals of varied initial orientation. From these studies, which form the subject of the present article, it became apparent that the initial observation of an approximate twin relation between the bands and the monocrystal was simply a special case. Our experiments show that deformation in rolling proceeds by a mechanism analogous to those which have already been observed in the simpler cases of tension and compression. Micrography—in particular, the formation of etch figures—has been applied to the quantitative study of these orientations. In addition, observations have been made of slip lines, of thin oxide films yielding interference colors, of thick films in polarized light, and of etchants giving "engraving." These micrographic methods for studying orientation have established the orientation relationship without any ambiguity, whereas X-ray methods would have given only a statistical result because we were often dealing with thin bands (2 to 100 microns) and even narrower connecting zones covering a maximum of 20 microns. Specimen Preparation and Methods The Al-3 pct Mg alloy was prepared from 99.95 pct A1 and is of the type used industrially in France for brilliant anodized finishes under the name of Brillalumag. This material combines the normal commercial properties with an enduring brilliance due to the protection of a thick, but perfectly transparent, film of alumina.&apos; The monocrystals were prepared by the method of critical deformation followed by prolonged annealing. Great care was taken to insure perfect homogeneity of composition, to eliminate included crystals,6,7 and to avoid the formation of undulations during oxidation. The critical deformation for this alloy is about 1.2 pct (1-l0/10x100) and the subsequent annealing was for one week at 500 °C after gradual increase of temperature (35°C per hr). The crystals thus prepared had a section of 10x5 mm and a length of 20 to 40 mm. Each of these crystals was polished electrolytically and etched for the formation of etch-figures with the classical reagent.&apos; The orientation was then calculated from their angles, as measured with a goniometer microscope.

Jan 1, 1954

By A. A. Smith, J. S. Smart, A. J. Phillips

The preparation of a sufficient quantity of high-purity copper for extensive laboratory use in the study of impurity effects has been an integral part of a research program in progress at the Central Research Laboratory of the American Smelting and Refining Co. for the past several years. Initially the degree of purity desired was that necessary to meet two essential requirements for experimental accuracy: (I) no impurity was to be present in the copper in an amount capable of producing a detectable effect on the properties to be studied, (2) even the minor changes in propertties caused by the addition of extremely small amounts of individual elements were to be measured without significant interference from contaminants. In the course of the investigation, evidence has accumulated to justify the conclusion that this copper is of exceptional purity; in fact, no impurity can be detected by any chemical method or spectrographic technique known to the authors. The present paper describes the method of production of the copper and presents some of its properties. Preparation oF High-purity Copper The elimination of impurities from commercial electrolytic copper is accomplished by a three-step purification process. The first operation consists of an electrolysis through a purified CuSO4-H2SO4 electrolyte using bagged anodes, low current density (5 amp. per sq. ft.) and low tem- perature (25°C max.). The electrolyte is prepared from commercial Cu2SO4 and is purified by heating the solution and adding I gram Fe as Fe2(SO4)3 to each 100 grams dissolved copper; sufficient hydrated oxide of copper, prepared from Cu2SO4 and NaOH, is supplied to precipitate Fe(OH)3, which carries down arsenic, antimony, tin, selenium, tellurium and other minor constituents. Silver and remaining traces of lead are removed by addition of Na2S to the acidified filtrate, which is then reatered after standing hot overnight. The cold solution is made up to 30 grams per liter Cu and 150 grams per liter H2SO4 and introduced without addition agents into the electrolytic system, which consists of a double row of hard-rubber battery boxes with the inside webbing and partitions removed, arranged in seven steps of ascending height. Electrolyte is uniformly supplied to the two highest cells by glass siphons operating from a constant-level reservoir, and flows by gravity through the bank of seven cells, entering each at the bottom and leaving at the top. Glass air lifts continuously supply the returning liquid to the constant-level reservoir for recirculation. Each cell contains three 4 3/4 by 4 3/8 by 1-in anodes cast from high-quality electrolytic wirebar copper, various lots of which have been used with equal success. The anodes are pinned to sheet copper hangars shaped to prevent crawl of the electrolyte to the multiple-wired bus bars—which would result in fouling of the contacts—-and hang inside wool flannel bags stretched over open wood frames. The deposit

Jan 1, 1941