Search Documents

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Mario Gerards

Maturing populations create an increase in the demand for the type of non-ferrous metals, which are used in the manufacturing of electronic products. The depletion of existing high-grade deposits, make it necessary to boost the efficiency of beneficiation processes and most importantly the yield (recovery rate of the value commodities). Increasing demand now makes it worthwhile to tap into resources, which were previously considered waste, for example secondary deposits such as tailing ponds and electronic waste. In order to achieve increased yields, increasingly finer, or even ultra-fine fractions have to be treated. In most cases, mineral characteristics such as size and density call for non-mechanical, high-capacity technologies to be used. There are various technologies that allow for the separation of fines and ultra-fines. This paper outlines the dynamics and efficiency of pneumatic flotation with emphasis on its application to the recovery of non-ferrous metals, from electronic waste. The conventional agitator flotation technology of an electronic waste processing plant was not able to recover ultra-fine non-ferrous metals satisfactorily, due to losses within the tailings. Because of its adaptability and its inherent suitability for non-ferrous metals, pneumatic flotation has been incorporated to the existing process achieving excellent results. The merit of the process lies in the state of the art technology, which does not utilize compressed air and any rotating parts, which results in a reduction in wear and energy requirement, both features of this innovative technology. In addition, the use of pneumatic flotation resulted in a significant reduction in residence time, when compared to mechanical flotation. Pneumatic technology is able to influence air bubble size in a flotation cell, by changing the speed and pressure of the slurry stream. Higher slurry velocities lead to the formation of smaller air bubbles, which is required for the successful flotation of ultra-fine particles. Conversely, decreasing the slurry velocity leads to bigger air bubbles. The optimum bubble size can be created according to different feed characteristics. This is important in case of feed fluctuations.

Sep 1, 2012

By ZáWang, F Hungerford, T Ren

Operations in an underground drill site have to co-exist within the mineÆs ventilation and operational system. The space requirements of a drilling operation have to be adapted to the limitations provided in available site space, which is usually defined by standard mining operations and geotechnical influences. These limitations affect borehole design, equipment positioning in the site layout and possible interactions with mining equipment and services such as water and power supply.The ventilation requirements for drill sites and the means employed vary with depth of the site, space and likely presence of gas. All drilling operations provide a particular service for the mine and in each case, drilling must operate in a manner which controls all gas, water and cuttings returning from the borehole. The various standpiping systems employed have evolved under differing influences and must cater for conditions during and after the drilling operations.The influences that gas content, pressure and flow, rib stability, cleat direction, borehole length, potential water pressure and flow have on a mineÆs operation and ventilation systems have to be considered in the design of standpipe length, diameter and fittings. Past history has a strong influence on common practice while worst case effects of a possible in-hole event should be catered for.This paper describes the early drilling systems and their limitations in ventilation and gas management. The drill site dimensions and set-up are discussed in the context of roadway conditions, equipment layout, ventilation and logistics. The use of standpiping to control all returns from the borehole is illustrated by referring to likely scenarios in a drilling site to achieve the most effective sealed depth to accommodate the worst case possibility of intersecting high pressure gas or water during the drilling operation. Practices to allow gas drainage in the return airway of a panel are described.CITATION:Hungerford, F, Ren, T and Wang, Z, 2013. operational management of underground in-seam drilling sites, in Proceedings The Australian Mine Ventilation Conference , pp 43-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Walter Renton Ingalls

IN SEVERAL papers and addresses during the past two years, I have dwelled upon some of the economic consequences of the war. The fundamental thought that I have sought to convey is that the world became immensely poorer by the war, not only in material wealth and population, but also in the psychology and morale of the people. I do not see how there can be any intelligent dissent from that statement. All the ideas of post-war prosperity were manifestly fallacious, manifestly fallacious from the outset. If there had been any truth in them it would have followed logically that a great war, with all its destruction of wealth, health and life would be a good thing. Therefore, let us have a great war every ten years or so. Such an idea would be both monstrous and absurd. Assuming then the acceptance of my premise, I have tried to show that the losses by the war could be made good in a short time, i.e., in a relatively short time, only by doing things a great deal better than formerly, and that the accomplishment of such a result called for greater transparency in industry, for industrial cooperation, for thinking in terms of industries as a whole, and for the greater exercise of engineering functions. All of this introduced, of course, the position and psychology of labor. I say frankly that I do not look for labor to contribute any constructive thought to the upbuilding. I neither expect it nor hope for it. This is a pity, for it could do so much for its own economic advancement if it would. However, it never has done so, but rather has benefited only from the exercise of the talents of the few, and the main hope now is to bring it into a passive state, dispelling the resistive fallacies that developed during the war. Let us briefly examine the nature of these.

Jan 1, 1921

By Munyaradzi Kwatara, Ron Schonewille, Edgar Peek, Juzer Tayabally

"The potential recovery of nickel from a South-American saprolitic laterite ore using the segregation roasting technique was investigated. The ore was heated to temperatures that ranged between 900 and 1 000°C in a rotary kiln. In all the tests, the laterite ore was first mixed with a predetermined amount of calcium chloride and either coal or coke. By varying the temperature, calcium chloride and reductant in the different tests, a preliminary set of optimal conditions was established for the specific laterite ore that was tested. A combination of chemical analysis and electron-probe-micro-analysis (EPMA) were used to determine and evaluate the effectiveness of segregation roasting on the recovery of nickel. The present paper describes the test procedure and the results that were obtained.IntroductionIt is known that laterite ore resources account for an estimated 72% of the world's nickel resources, with sulfide sources accounting for the remaining 28%. Yet sulfide resources account for 58% of the world's primary nickel production while laterite resources account for the remaining 42% [I]. There are numerous reasons for this discrepancy, but the most important one is the mineralogical and compositional complexity that is associated with laterite ore deposits. For example, this complexity currently offers only limited opportunities for upgrading, thereby creating capital intensive whole ore processing facilities. It then follows logically that the identification and application of a low-cost processing option for the treatment of laterites could potentially open up an opportunity for exploiting these vast untapped laterite resources.To this end, a preliminary screening investigation was initiated by Xstrata Process Support to evaluate the potential application of the so-called (nickel) segregation process as a unit operation that could potentially be integrated into a laterite processing flow sheet. Laboratory bench tests were performed on this segregation process and this paper details some of the findings from this preliminary investigation."

Jan 1, 2011

By K. Thuro, H. Käsling, C. Wieser, G. Nuijten

"The time-dependent behavior of brittle rocks during stress relaxation is of great interest for mining industry, nuclear waste disposal as well as tunneling and underground construction. Several studies have shown that both elastic as well as inelastic deformation occur during stress relaxation (Emery, 1964; Zang & Berckhemer, 1989). While elastic strain occurs already during the drilling process, inelastic deformation is time-dependent and can endure for hours, days or weeks. To investigate the evolution of microcracks during core relaxation, two crystalline core samples were recovered from high in situ stress conditions in Europe’s deepest mine in Pyhäsalmi (Finland). Samples were prepared for testing within one hour after coring such that a large portion of the time-dependent component of relaxation could be recorded over several days using ultrasonic velocity as well as acoustic emission (AE) measurements.Results from AE analysis show an exponential decrease in the number of events over a period of several hours. Repeated sudden increases of acoustic events can be related to the propagation or the interaction of cracks. In the first hours of recording also the signal energies reached the highest values and the increases in signal energy correlate well with increased event rates. On additional drill cores, P-wave velocities were measured parallel and in 45° distances perpendicular to the core axis. After core recovery, stress-induced microcracking caused an exponential decrease in wave velocities similar to AE rates. Lowest compressional wave velocities were measured parallel to the core axis and thus normal to the foliation and in the direction of the maximum in situ stress component. The highest measured velocities occurred parallel to the foliation plane. Within the samples, the anisotropy ratios were up to 1.37 at the beginning of the measurements and increased to values of up to 1.8 after 45 days. The wave velocity anisotropy is in agreement with the in situ stress orientations."

Jan 1, 2015

By J. Butra

The underground research presented in this paper was carried out in the two Polish copper mines: Rudna and Polkowice-Sieroszowice. The aim of the research was to determine stress field parameters. The measurement method and measuring positions are described as well as the measuring technique adapted to the geological and mining conditions of the Rudna mine and the Polkowice-Sieroszowice mine. The identified values and directions of principal stresses and horizontal stresses and their importance for optimization of mining operation and safety improvement are discussed.

Aug 1, 2013

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By N. E. Maccallum

(Cleveland Meeting, October, 1912.) ALMOST half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: ?What is the safe and economical limit of the open-hearth furnace?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own Conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Co., of Phoenixville, Pa., and their distinctive and important feature is, that they charge to twice the capacity of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Oct 1, 1912

By Craig S. Compton

The failure of the immediate roof or "roof skin" between installed primary and secundary roof supports causes hundreds of injuries and, on average one or two fatalities each year in U.S. underground coal mines. Conventional roof supports cannot cover enough roof area to adequately control these relatively small, but very dangerous rock falls. The 2006 Mine Safety and Health Administration (MSHA) accident database lists a total of 542 ground fall injuries, including 10 fatalities. An analysis of the database suggests that 434 of the injuries and three of the fatali­ties can be attributed to roof skin falls (See Figure 2). The key to controlling falls of the immediate roof or roof skin is maximizing the area of roof coverage ilnd confining these relatively small loose rocks. Roof screen offers maximum coverage of the immediate roof. Depending on the size and configuration of the screen panels, coverage of up to 100% of the roof area is possi­ble. Screen also offers a first line of defense for machine operators working in the face area by confining or deflecting small rocks that can come loose during mining or roof bolt installation. Figure 1 shows an example of the protection screen provides dur­ing bolt installation. Although the benefits of screen are well-known, mining com­panies in some areas of the U.S., mainly Northern Appalachia and the Illinois basin, are not convinced that roof screen is the best tool for dealing with roof skin control issues. The logistics of material handling, possible ergonomic injuries to workers, and the costs associated with installation are delaying the acceptance of screen as an on-cycle roof support tool. Other mines however, have concluded that installing roof screen can be cost-effective when compared to the cost of lost time accidents, training of replacement workers, or returning to already developed entries for the cleaning and rebolting process.

Jan 1, 2009

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, Gary O’Connell, Denis Shishin, Jeff Chen, Francis Letarte

"Knowledge of slag properties is required for the optimisation of smelting operations. The phase equilibria and viscosities of the Al2O3-CaO-FeO-Fe2O3-MgO-MnO-NiO-Cr2O3-SiO2 slags at conditions of interest to Koniambo Ni-laterite smelting operations have been investigated. High-temperature re-equilibration phase equilibrium experiments of industrial slags followed by rapid quenching and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) have been undertaken in the olivine and pyroxene primary phase fields at temperatures between 1475 and 1600°C and SiO2/MgO weight ratios between 1.57 and 2.09. Phase equilibria predictions were performed using FactSage thermodynamic software. A slag viscosity model available in the FactSage thermodynamic package has been used to calculate the viscosities of the liquid slags. The Einstein-Roscoe equation combined with the predicted phase equilibria data have been used to estimate the viscosities of the slag slurries (slag + solids). The information provided can be used to assist in the evaluation of the furnace performance, to assess further optimisation of slag composition and to explore possibilities of targeted feed changes.INTRODUCTION One of the key steps in the production of ferronickel from nickel laterite ore at Koniambo Nickel SAS involves reduction and smelting of pre-dried nickel-bearing saprolitic ore (high Mg and Si) in an electric furnace at temperatures up to 1650°C. The characterisation of the slag properties as functions of key operational parameters, such as, temperature and composition, including liquidus, the proportions of solids and viscosity, is essential for improving control and optimisation of the operations. The slag produced in the smelting process is a complex oxide system with the major chemical components including Al2O3, CaO, Cr2O3, “FeO”, MgO, “MnO”, “NiO” and SiO2. Characterisation of these multi-component systems using a solely experimental approach becomes increasingly complex as the number of components is increased."

Jan 1, 2017