Search Documents

"The Val d'Or Division now comprises the Lucien C. Beliveau Mine and Concentrator (formerly the Pascalis, described below) and the Chimo Mine. Cambior acquired an initial 50% interest in the Chimo Mine in May 1989 and the remaining 50% in April 1990. Cambior's share of 1989 production was 2121 ounces; the company expects to net 23 750 ounces from Chimo in 1990. Pascalis MineUPDATERenamed the Lucien C. Beliveau Mine at its official inauguration in September 1989, the mine is exceeding forecasts, producing over 11 500 ounces of gold in the first half of 1990. Cambior expects 1990 production to total 34 000 ounces.IntroductionThe Pascalis Mine is located 16 miles east o f Val d'Or, Quebec, and is accessible by a three mile gravel road off highway 117 (Fig. I).The property is wholly owned by Cambior.The Pascalis gold deposit consists o f a sub-vertical diorite dyke 1000 ft long by 30 ft wide containing quartz and tourmaline veins with inclusions of pyrite and native gold . Three vein systems ca n be seen in the deposit , the most important being tensile veins oriented at a right angle to the direction of the dyke and inclined at 40 degrees. These overlapping veins vary in thickness from 4 in. to 40 in. and occur at intervals of six to ten ft. The deposit is, therefore, very difficult to evaluate; a complete evaluation would require drifts over the whole width of the dyke combined with relatively short drill holes (Fig . 2)."

Jan 1, 1990

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By W. Gibson Jaworek

Of increasing importance to the student of fuels economics has been the extent to which different primary energy sources can substitute for each other in the various energy markets of the nation. Knowledge of the nature and extent of fuel interchangeability can aid the fuels economist in projecting trends of energy utilization, as well as giving him a better understanding of the past and present conditions of fuel markets. It is also important to the consumer to know just how much flexibility he can maintain in his energy consuming operations. And, finally, various governmental bodies show keen interest in the degree of energy substitutability in determining public policies concerning the fuels industries. The presence of excess fuel production capacity in the United States during the early 1960's indicates that fuel interchangeability should become more prevalent in the increasingly competitive energy markets of the nation. Discussion of fuel intercompetition is almost always restricted to qualitative terms-because of the lack of comparable statistical data, between the different energy sources in geographic or "type-of-use" fuel, markets. There are exceptions, of course, such as, the excellent fuel consumption data which are available on steam electric generating plants throughout the nation. In other sectors, statistics are at best incomplete.' Inmost instances, indirect fuel consumption indicators, such as sales of fuel burning equipment, are extensively used to measure market shares of a particular fuel; however, these indicators are hard to evaluate precisely without prior knowledge of the total competitive market.

Jan 1, 1961

By K. M. Ed

MR. J. C. NICHOLSON: The author has discussed his subject in a very thorough manner. One difficulty is the tendency to regard a 'permitted' explosive as a 'safe' explosive. There is no such article as a safe explosive; any explosive is only as safe as the man who handles it. In making up the primer, the method illustrated in the paper is alright for the ordinary explosive but not so for the sheathed explosive, for the sheathing would be punctured. MR. T. L. McCALL: I fee! quite certain that there would be little, if any, trouble from flame shots or misfires if the author's suggestions were carried out. There is a tendency on the part of the shot-firer to over-shoot, so as to bring clown more coal for the miner, and frequently a shot has not sufficient burden imposed upon it. Shooting one hole may not only lessen the burden on an adjacent hole, but may practically release it altogether, in which case the second hole should be fired with a very small charge, or perhaps it might not be necessary to shoot it at all. While the paper refers to shooting in the coal only, it should be under-stood that the instructions given are equally applicable to brushing shots. I do not wish to bring up any contentious point, but would the author say a word on cushioning with air gaps and on multiple shooting? Single shooting in rock might open up a feeder of gas which could be ignited by the ?second shot.

Jan 1, 1940

By Rudolph H. Jacobson

The leaching of heaps or sub-marginal waste ore dumps as it is practiced throughout the Southwest as well as other parts of the world, is the major method of secondary recovery of copper. In 1970, twenty percent of all domestic copper was produced by dump leaching operations (l). In recent years, this method has been successfully extended on a limited scale, for the recovery of uranium from low-grade ores (2). It is inevitable that this technique will be increasingly employed in metal production to satisfy the insatiable demand of our mineral based society. Although dump and heap leaching has been used effectively for some time (3) , its application has been more of an art than a science. Therefore, it is essential that we learn about the important factors and parameters affecting this versatile process so that we may make increasing use of this technique in the future. The dump or heap leaching process encompasses the preparation of ore for-subsequent inplace leaching, the flow of solutions and ionic species through porous rock masses, the leaching of minerals with inexpensive and, if possible, regenerable lixiviants under prevailing conditions of the inplace environment, and the recovery of metals from the pregnant liquors. It is evident that this comprehensive scope of dump or heap leaching falls under the realm of interdisciplinary science and engineering requiring the application of the principles of physics, mineral engineering, hydrology, computer modeling, operations research, economics, and allied disciplines. An exhaustive study of the phenomenology of a leach dump or heap requires detailed knowledge of the simultaneous interaction of'

Jan 1, 1972

By Martin J. Gavin

[The theory of fractional "eduction" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil f roan the oil shales of the United States. The term fractional "eduction" gives expression to the rather common belief that when an oil shale is he-test et produces light, low-boiling oils at to temperatures, and increasingly heavier, higher-boiling oils as the temperature of retorting rites. The theory evidently had its is origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases. Thus, gasoline is produced from petroleum at relatively log: temperatures, kerosene at a higher temperature, and heavier products such as gas-oil and lubricating distillates at still higher temepratures, The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and en some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperatures, and so on. Such retorts are usually designed to operate continuously, and. have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts expect that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale basses to zones of increasingly higher temperatures, the vapor lines leading from these zones will remove increasingly heavier products such as kerosene, gas-oil, etc.]

Jan 1, 1924

By E. H. Rose

THE most useful guide to the role of lime in flotation is the view that the chemistry of any flotation operation is primarily a pattern in relative solubilities. We have the coming together of a number of minerals, reagents, fortuitous salts, water, and oxygen, many of which have not been previously in contact with each other, and every one of which is free, at least to some extent, to abandon old alliances and to form new ones. Of one thing the operator may be sure, and that is that, when equilibrium has been reached, those new chemical combinations will have formed which are the least soluble combinations possible to the environment. The laws of solution govern the operation, which means that relative concentrations are always a factor, and temperature frequently is. What the operator is really doing when he chooses his reagents .in the first place (empirically or otherwise) and works out their? optimum amounts, is to provide an environment in which (1) the least soluble possible compound of the mineral he desires to float is one which is also non-wettable, while at the same time (2) the least soluble compounds possible to the minerals he desires to depress are wettable. Since all metathesis is reversible, perfection is impossible to achieve, and the operator is constantly striving to establish that combination of concentrations which will drive each and every particular reaction as far as possible in the direction he desires it to go, in accordance with the law of molar concentration.

Jan 1, 1939

By Earl Oliver

IN times like these, the A. I. M. E. and similar societies have their greatest usefulness. . . . Individuals and companies acting alone in the development of public opinion are merely voices crying in the wilderness. United and organized they make a great force that can and does influence public action. . . . What part, if any, then, shall the A. I. M. E. take in these great stabilization processes of civilization? Shall it help to give direction and force to scientific knowledge which comes within its field of activity or shall it merely develop more of it? . . . Is it the A. I. M. E.'s function to help bring system, order and direction out of this situation so that the world can again have forward economic movement, or should it rest on its oars until other agenciess develop that public understanding and direction so necessary for economic progress? As we understand the functions of the A. I. M. E. Petro¬leum Division, they are to discover and promote knowl¬edge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends on the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas.

Jan 1, 1932

By Chen Wen, Li Zhao-jia, Zhao Qiang, Ning Shun-ming, Tang Sanchuan, Wang Hong-qiang

"The carbon-burdened and cold-bonded pelletizing-electrosmelting process is used to dispose low-grade manganese, and the qualified rich-manganese slag is obtained. On the condition that reduction roasting temperature was 1000?, reduction time was 45min, particle-size was -1mm, reductant dosage was 1.6%, basicity was 0.3, smelting temperature was 1410?, smelting time was 60min, it had a good effect on the melting between slag and metallographic phase, the manganese content was 32.58%, manganese recovery was 92.16% in the slag; while the iron content was 94.40%, iron recovery was 95.32% in the metallographic phase. It was proved by the demonstration tests.IntroductionManganese is an important raw material for steelmaking, which is extensively utilized in modern industry, the consumption of manganese for iron and steel industry accounts for 90% to 95%. After mining over 30 years, the high-grade manganese resources drop markedly, especially with the hypergrowth of steel industry, the domestic manganese is far from the requirement, as a result, we have to buy significant quantities of manganese overseas. Besides, the property of imported manganese is more and more complex, and the high-grade and lump manganese decrease year by year, while the fines and high-crystal water manganese are on the increase. Therefore, how to make effective use of domestic low-grade manganese and intensify the manganese’s smelting is an effective approach to reduce the cost of manganese series ferroalloy and improves market competitiveness[1-4]. It has important practical meaning."

Jan 1, 2012

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014