Search Documents

By Ramdane Bahar

The new Algiers airport building is a reinforced concrete building of more than 80 thousand square meters of floor slabs. It is located at Dar-EI-Beida, near the old passenger terminal, about 20 km east of Algiers. The project is designed to receive about six millions passengers annually and leaves the possibility of future extension. Due to the presence of a top layer of compressible soil and great concentrated loads transmitted to the foundations, the building is to be founded on 1730 bored piles of 1.2 meter diameter varying in length between 14 and 28 m. Construction work started in 1986 and was interrupted in 1996 due to financial difficulties when the structure was almost complete. The structure was left unattended for more than three years without any weatherproofing and in 1999 a new firm was appointed to complete the work and hence an evaluation of the existing structure was necessary. This paper describes and discusses the foundation design, construction supervision, site quality control and assessment by the parallel seismic method of the deep foundations built in cohesive soils. The variation in soil conditions and identified geotechnical and hydrogeological problems associated with the development of the area, required a thorough knowledge of the soil conditions. A variety of tests, involving more than 200 locations, were carried out. The ground investigation, pile tests as well as different problems encountered during piles construction, are presented.

Jan 1, 2002

By Lauri E. K. Holappa

The aim of the metallurgical process development is, nowadays, to search for the shortest, most economical, more environmentally friendly and sustainable route to convert raw materials to finished products. Recent progress in steelmaking processes ? BOF and EAF - has also motivated to search for more advanced casting technologies to shorten process route. Continuous casting, which became industrially feasible in the 1960s, is now a mainstream technology with over 90% share of the world steel casting. After the 1980s, the increase in steel production and consumption, particularly from automobile, construction and home appliances industries, required steel manufacturers to accelerate production with more concise procedures, so that near-net-shape casting took the trend of development in order to bypass and simplify the downstream processes, e.g. cold/hot rolling mill or extrusion mill, to directly obtain finished products with required geometries. Progress in flat and long products changed the industrial operation pattern, strengthened steel production efficiency, and formed the operation concepts of the integrated steelworks and mini-mills, respectively. Thin slab casting and strip casting have represented the most important progress and promise, in the recent years, of such innovations furthermore strengthening the production efficiency and, concurrently, coinciding with the demands of environmental protection and sustainability. This paper reviews the most recent progresses in near-net-shape casting and prospects the impacts to steel industries as well as the development trends of steel production, in general.

Jan 1, 2006

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

By Steven W. DeCou, Marcus R. Jensen, Stephen Navin

The Lake Mead Intake No. 2 is a project constructed for the Southern Nevada Water Authority which includes a 12-foot diameter lake tap and intake shaft constructed in over 225 feet of water; 1650 feet of 16x14-foot horseshoe-shaped tunnel leading to a forebay that is 165 feet long, 35 feet tall, and 30 feet wide; twenty-two 4-foot diameter steel lined well shafts extending 325 feet from the ground surface to the forebay; 3500 feet of 12-foot diameter pipeline crossing a bay in Lake Mead that has water depths of up to 80 feet; and 2700 feet of 9-footdiameter steel-pipe-lined tunnel. Major site grading for a future pumping station in the area above the forebay is also included as part of the project. The project is on the schedule’s critical path for completing the first phase of a $2 billion water supply program for the Las Vegas Valley. In this paper, the owner, the designer and the construction manager present a discussion of the risk management strategies that were used to control costs, minimize project delays, and facilitate problem resolution. The discussion includes an assessment of the effectiveness of the risk management strategies in meeting these objectives. This paper will be of interest to owners and engineers planning underground projects, especially those projects that present unique risks during the construction phase.

Jan 1, 1999

By R. W. Prouty

THE methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz., fall into two divisions because of the difference in occurrence, manner of prospecting, and methods of mining: that for the underground operations and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three classes: Replacements of limestone, replace-ments of porphyry, and replacements of contact breccia The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies it is exceedingly difficult, without sampling, to deter-mine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft. As some of the ore-bodies have a thickness of from 100 to 300 ft., it can be seen that the smaller ones form a difficult problem both in prospecting and in estimating.

Jan 11, 1922

Background The annual awards, which have been given by the US National Committee for Rock Mechanics since its inception in 1969, recognize out- standing research in rock mechanics. Such recognition has always been accompanied by a plaque or certificate for the winners and a presentation at the symposium awards banquet. Starting this year, the US National Committee will give the winners even more recognition and allow the rock mechanics community to benefit from the papers by publishing abstracts of the work in the proceedings of the 25th US Symposium on Rock Mechanics and in various society journals and news letters. "We hope this will stimulate the production of more research papers," said William R. Judd, former chairman on the subpanel of awards. "It's beneficial for researchers to have their work published as an award paper." There are four categories of awards: Basic Research, Applied Research, Case History, and Student Masters' Thesis. Approximately ten papers are nominated annually for each category; however, in some years awards are not made in all four categories. For instance, there were not enough case history nominations in 1983 for an award, but there were two equally outstanding recipients of the award for applied research. The winners of the 1983 research awards reflect the wide variety of professions involved with rock mechanics. They are introduced on the following pages by category, and accompanied by an abstract of the paper

Jan 1, 1984

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By John W. Pack

At present the manufacture of metallic zinc, or spelter, in Missouri, is carried on only at the establishments located at Carondelet, or South St. Louis. Although the development of the industry has not yet reached that fulness which it has attained elsewhere in the United States, still the commanding advantages of position of these establishments are so evident that the prospective importance and magnitude of spelter manufacture in this State, and especially at this locality, can hardly be doubted. A study of the chemical and technical aspects of the business of these points cannot be without interest to the metallurgist as well as to the capitalist. I have endeavored to investigate, as far as was practicable, within the limits of a paper of this character, some of the problems connected with this industry, at the same time making a few comparisons of the results attained at some of the Carondelet works with those of other establishments with regard to which information could be obtained. In the prosecution of these studies I have been kindly aided by the managers of Carondelet establishments, and by Prof. Charles P. Williams, Director of Rolla School of Mines. To the latter I am especially indebted for assistance in regard to methods of analysis. To all these gentlemen I return my thanks for their valuable aid. Other sources of information will be duly credited in their proper places.

By John W. Pack

AT present the manufacture of metallic zinc, or spelter, in Missouri, is carried on only at the establishments located at Carondelet, or South St. Louis. Although the development of the industry has not yet reached that fulness which it has attained elsewhere in the United States, still the commanding advantages of position of these establishments are so evident that the prospective importance and magnitude of spelter manufacture in this State, and especially at this locality, can hardly be doubted. A study of the chemical and technical aspects of the business of these points cannot be without interest to the metallurgist as well as to the capitalist. I have endeavored to investigate, as far as was practicable, within the limits of a paper of this character, some of the problems connected with this industry, at the same time making a few comparisons of the results attained at some of the Carondelet works with those of other establishments with regard to which information could be obtained. In the prosecution of these studies I have been kindly aided by the managers of Carondelet establishments, and by Prof. Charles P. Williams, Director of Rolla School of Mines. To the latter I am especially indebted for assistance in regard to methods of analysis. To all these gentlemen I return my thanks for their valuable aid. Other sources of information will be duly credited in their proper places.

Jan 1, 1875

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Kuzugundenli OE, Nagaraj DR

Organic complexing agents have received special attention over the past few decades in the search for reagents for improved flotation separation of minerals, especially non-sulphides. The majority of such reagents that have been proposed over the past few decades have remained largely a laboratory curiosity, except perhaps alkyl hydroxamates, because their selection is seldom based on commercial viability. In this regard, the choice of complexing agents such as oximes may be more realistic because of their widespread use in solvent extraction of copper. Our earlier studies have confirmed that they are also effective as collectors for copper oxide minerals, including chrysocolla which is the most difficult copper mineral to beneficiate. The flotation behaviour of chrysocolla for several structurally-related hydroxyoximes were studied as a function of pH and oxime concentration and the role of structural features examined. The structural changes studied included substitutions in both chelating and non-chelating parts of the molecule. The results indicated that, contrary to expectations, many of the structural changes in the basic molecule, salicylaldoxime, do not have a positive effect on collector efficiency. The reduction in collector efficiency is rationalised on the basis of possible steric factors affecting complexation and packing of the collector species on the mineral surface as well as effects due to changes in electron density brought about by substituents. Introduction of alkyl substituents on the oximic carbon of salicylaldoxime yielded the highest collector efficiency.

Jan 1, 1993

By John Suman

DURING the past few years the taking of cores in drilling with rotary equipment has been perfected to a remarkable degree in the Gulf Coast fields of Texas and Louisiana. Taking of cores is becoming quite a common thing, especially in the newer fields, and drillers are becoming expert in this work. The writer has seen cores 5 to 8 ft. long taken with great ease in wells as deep as 4500 ft. Coring is doing much to remove the prejudice which so many petroleum engineers seem to have against .the use of rotary drilling equipment for exploratory work. Some operators .are now claiming that when used with a reasonable amount of coring the rotary system is even more satis-factory than cable tools for exploring in certain territory. A case has recently been pointed out in the South Electra field of North Texas, where producing oil sands, passed over by cable-tool drillers, are being brought in with rotary equipment. It seems that in this particular territory the sands are rather thin. Cable-tool drilling was carried on for the most part in a wet hole and the red mud encountered in drilling caved into the hole very badly, so that the cuttings showed mostly red mud and the driller, thinking that the sand did not amount to anything, carried his water string through the sand. The later .operators, drilling into the sand with rotary equipment and coring it, found that it was well worth testing.

Jan 10, 1922

By Richard H. Gates

INTRODUCTION The U. S. Army Corps of Engineers is developing chemical explosive excavation as a construction technique for use on Civil Works projects. Large chemical charges are being used in multiple charge arrays in a variety of media and topographic situations to achieve actual construction projects. The target is the development of chemical and nuclear explosive excavation as an accepted cost-competitive construction technique. Military research using explosive excavation is also being conducted to apply this technique to military engineering for combat purposes and to military construction. The information gained from both the civil and military research is integrated into the overall development of explosive excavation. This research and development work is being conducted under the auspices of the U. S. Army Engineer Waterways Experiment Station Explosive Excavation Research Laboratory (EERL) located at Livermore, California. This organization was formed in 1962 as the Nuclear Cratering Group (NCG) to carry out the Corps of Engineers (OCE) portion of a joint agreement with the Atomic Energy Commission (AEC) to develop nuclear explosives for construction purposes. The AEC, through the Plowshare Division of the Lawrence Livermore Laboratory at Livermore, California, has been responsible for developing nuclear explosives, conducting nuclear cratering experiments, developing nuclear safety information, and developing methods for predicting the shape of the craters. The Army part of the program includes corollary chemical high-explosive cratering experiments, participation in the AEC's nuclear cratering experiments, and development of

Jan 1, 1997

By M. D. Voegele, C. Fairhurst

INTRODUCTION A computer study of excavation support loads in tunnels and other excavations in discontinuous rock masses was undertaken with the distinct element method introduced by Cundall (1971). In the distinct element method the rock mass is modeled as a composition of individual blocks of rock defined by the joint planes. Normal and shear deformation laws are ascribed to the joint surfaces; the blocks of rock themselves are considered to be rigid. The particular version of the program utilized in this study ran a mini computer and used inter, active techniques for the input of geometrical data such as joint orientation and spacing and subsequent display of rock mass deformation and other data. Two major aspects of the behavior of excavations in jointed rock masses are examined in this paper: i) the behavior of unsupported excavations in rock masses with varying joint configuration, joint properties and in situ stress fields; and ii) the modification of the behavior of similar excavations when support is provided. In the latter case the excavation behavior was examined through the use of ground reaction curves. THE DISTINCT ELEMENT METHOD The Distinct Element method introduced by Cundall (1971) is a computer based analysis that simulates the behavior of a system of discrete, semi-rigid rock blocks. Block interactions are governed by realistic friction and stiffness laws; each block may undergo unlimited displacement and rotation while progressive failure is modeled.

Jan 1, 1982

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

Karl L. Fetters moves to the front of the AIME organization this month as the 1964 President of the Institute. He will take the chair vacated by outgoing President Roger V. Pierce at the Annual Meeting in New York, already well-rehearsed in his forthcoming duties after a year of preparation as AIME President-Elect. Dr. Fetters is highly qualified for his new responsibilities on both the administrative and professional level. For the past five years, he has been vice president for research and development at The Youngstown Sheet and Tube Co. in Ohio, where he has achieved wide recognition as an out- standing metallurgist and executive. A native of Alliance, Ohio, he obtained his early education in the public schools of his home town and displayed a singular precocity when he launched his professional career as a chemist for the Morgan Engineering Co. at the age of 16. His new career, however, was soon set aside in favor of four years of higher education at the Carnegie Institute of Technology, whence he emerged in 1931 with a bachelor's degree in metallurgical engineering. Surprisingly, and perhaps owing to the employment stringencies of the Depression years, the first job his new qualifications earned him was that of stationary engineer at the Cunningham Sanitarium in Cleveland. After two years of ministering to the mechanical ailments of this institution, Dr. Fetters relinquished his post for a more suitable one in the field of metallurgy.

Jan 2, 1964

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By J. M. Clark

For some years past, those interested in the development of the increasingly important mining industry of Canada, havc urged the adoptioi~ by the Dominion Parliament of a federal mining-law, which would have the force and stability of statutory enactment. At present, placer-mining in the Yukon Territory is governed by the Yukon Placer Mining Act. All other mining under federal jurisdiction is governed by Orders in Council and Ministerial Iiegulations. In the earlier stages of development, it is perhaps a matter of neces~ity that these important matters should be so dealt with; but it is now felt that the time has come when mining-rights in the extensive regions under federal control should be put on a permanent basis, and that any changes required from timc to time should be made only after full and open discu~sioii in Parliament. A short sketch will suffice to indicate how vast and varied the interests affected really are. When the Dominion of Canada mas constituted by the Inlperial Statute known as the British North America Act of 1867 (which into force by proclamation on July 1 of that year), it comprised only the present Provinces of Ontario, Quebec, Nora Scotia, and New Brunswick; but provision was made for the inclusion of Newfoundland, Prince Edward Island, British Columbia, Rupert's Land, and the North West Territories. Subsequently Rupert's Land and the North West Territories were acquired, the Crown Colonies of British Columbia and

Jan 1, 1912

By Y. Astafyev

In applying computers at the enterprises it is necessary to develop an open-pit model which completely corresponds in its structure, properties and characteristics to real open-pit mining. This model is used for controlling open-pit operations which ultimately define the system controlling ore reserves. The preparation and reserving of the latter are highly expensive and labour-consuming, therefore the investigations are aimed at developing the ore reserve control system which is capable to provide open- pits with the necessary ore reserves on the basis of equipment relibility characteristics, and thus helps to solve the ore reserves problem which is to define their optimum dimensions under conditions of stochasticity of production processes. In accordance with the tasks of the investigation it may be conventionally divided into three parts. The aim of the first part is to develop a structural open-pit system model consisting of a set of elements which are represented here by drill-rigs, shovels, trucks, unit trains, plant receiving bins and dumps (Fig. 1). The combination of similar elements makes up technological components the sequence of which forms simple systems. The latter, in their turn, grouping according to the type of mined rocks and inter- acting in parallel, form the "Stripping" and “Mining” subsystems. In addition to this, there is the "Ore Reserves" subsystem which serves as a "store" and includes opened-up, prepared and ready for extraction ore reserves.

Jan 1, 1977

By C. O. Aksoy

Operating the underground marble quarries effectively, it is important to evaluate the deposit blocks economically which are affected by the suitability of the topography and configuration of bedding. The joint sets within the deposit and the spacing between these discontinuties are also of great importance. In this study, the marble deposits that could be geomechanically eligible for underground excavation have been selected throughout Turkey and these selected reserves have been classified accordingly by Q-Rating System. These classified marble deposits that forms groups of 1,2, and 3 (groups were determined by evaluating the O-rating, topography, quarry situation, cracks, joints etc.) are convenient for this type of production. Nevertheless, when the auxiliary factors (topography, location, production method etc.) regarding the deposit have also been investigated, the most convenient sub-group of deposits (Afyon Tiger Skin, Burdur Beige, Diyarbakir Pink and Mugla White) have emerged. The sizing of the pillars have been performed utilising Bieniawski?s stress profile. The LAMODEL software, developed by National Institute for Occupational Safety and Health (NIOSH), USA and run under the laminated displacement discontinuity method, has been used to size the pillars. This work brings in a novel opportunity to Turkey, in which no underground marble quarry has been attempted up-to-date similar to its several examples in Italy, USA, etc. This study serves as a reference for the marble operators and for the pioneering application of laminated displacement discontinuity method in hard rocks.

Apr 1, 2005