Search Documents

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Guanghua Wen, Jian Li, Mingmei Zhu, Fei Xiong, Shengjian Cao

"Small inclusions removal from molten steel in a continuous casting tundish by gas bubbles, which were generated in the turbulent flow region by introducing inert gas, was analyzed theoretically and the inclusion-bubble adhesion and flotation process was also observed by high-speed photo-graph in water model. Results showed that small inclusions in the range of 20-50µm removal from molten steel by bubbles flotation involves three stages: contact, adhesion and flotation. The inclusion-bubble adhesion processes include two ways: inclusions adhering to the upper part of the bubble and inclusions adhering to the lower part of the bubble. As the bubble floats up, the number of inclusions adhering to the bubble are increased. The proper size of bubbles, which could enhance small inclusions removal efficiency, should be controlled in the range of 1-2mm.IntroductionReducing inclusions content in molten steel is a very important way to improve quality of steel, and one of the main tasks in steel making process.A variety of methods have been used for inclusions removal in molten steel. At present, the main approaches to remove inclusions are gas stirring, slag cleaning, filtering, centrifugal separating, and by means of ultrasonic or electromagnetic field. Among these techniques, gas stirring is the most widely and effectively method for inclusions removal. Inclusions in molten steel will be aggregated and generated to form larger size inclusions, and subsequently floated to the surface of molten steel by buoyancy; meanwhile, some inclusions will be adhered to bubbles and floated together to metal-slag interface where inclusions are absorbed by the covering slag layer. Some research work showed that flow behaviors of small bubbles are different from that of big ones [1-2], and smaller bubbles are more efficiency for fine inclusions removal in molten steel.There are many methods to generate bubbles. During steelmaking process, highly turbulent flow in the ladle shroud can split introduced inert gas into small bubbles, which enhances the removal of fine inclusions from molten steel. Turbulent flow of molten steel injected into tundish from ladle shroud has a high speed and it is a strong turbulent area in continuous casting. The gas can be introduced into the shroud below the slide gate. The high turbulence flow would break up the gas into small gas bubbles. Fine inclusions will be easily adhered to small bubbles and subsequently floated to the surface of molten steel. Generation of small bubbles in ladle shroud have been studied in some literatures [3-4]. Some research have analyzed the fine inclusions removal with injecting gas from the ladle shroud by mathematical simulation, and the results show that the refining method can obviously improve the removal efficiency of fine inclusions in tundish [5-8]."

Jan 1, 2013

By C. A. Moseley, M. B. Kahle

The Gulf Coast Region has been the center of extensive lignite exploration and development activity in the past 10 years. Currently, 27.2 Mt (30 million st) of lignite are mined annually, the majority of which is uncovered by large walking draglines. Projections indicate that production could reach 125 Mt (138 million st) by 1990. As mining moves to deeper depths, removal of overburden becomes the decisive factor in mine planning and cost. The geology of a region plays a key role in the selection of an overburden removal system. While alternate stripping methods must be analyzed to determine the most economical and operationally sound method, so far bucketwheel excavator systems seem to be the best method for removing large volumes of soft, unconsolidated material that is found at projected mining depths in the Gulf Coast region. Geology of Gulf Coast Lignites Extent Distribution of the principal tertiary lignite-bearing deposits in the Gulf Coast Lignite province extend from the Texas-Mexico border to the Alabama-Georgia state line (Fig. 1). The lignite-bearing strata includes portions of eight states: Texas, Louisiana, Arkansas, Missouri, Kentucky, Tennessee, Mississippi, and Alabama. Lignites occur primarily in the Wilcox, Claiborne, and Jackson groups in the Gulf Coast. The uppermost strata of the Midway group in Mississippi and Alabama also contain significant lignite resources. Reserves Commercial lignite seams in the Gulf Coast Lignite province range from 0.6-3 m (2-10 ft) in thickness. The estimated lignite resources throughout the Gulf Coast in seams greater than 0.9 m (3 ft) in thickness and up to 61 m (200 ft) in depth currently are estimated at 32 Gt (35 billion st). Table 1 shows these resources by state. Quality Lignite quality can vary within individual mining areas and seams. However, trends in quality occur because of the depositional environment, age, and west-to-east geographical location. Better quality lignites occur in the Wilcox group in Texas and Louisiana. Poorer quality lignites occur in the northern regions of the Wilcox group and those of the geologically younger Claiborne and Jackson groups. Environmental Conditions Gulf Coast province environmental conditions are ideal for successful mine reclamation. The lignite occurs in flat to moderately rolling terrain, a topography easily reproduced from the spoil dumps or spoil rows developed during the mining operation. High to moderate rainfall facilitates rapid revegetation. Evidence from current mine reclamation programs and ongoing test plot studies indicate that mined lands can be reclaimed to reach premining productivities. Sometimes productivities are even greater than that of premining conditions. Existing Mining Methods Present Mines & Production There are seven active mines in the Gulf Coast province, all located in Texas (Fig. 2). Lignite

Jan 8, 1983

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author&apos;s reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond&apos;s statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Willard R. Jillson

Within the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discnvered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky&apos;s mountain railroads&apos; was completed. The coals of. Kentucky are, broadly, separated into two geographic units—the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the state, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.—both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.87 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), &apos;which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per • cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85 per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent. In the western Kentucky field, the great increase in the percentage of sulfur is at once apparent. Ohio County with 3.78 per cent. is the highest and Hancock with 2.87 per cent. is the lowest. The percentages by counties is as follows: Hancock, 2.87 per cent.; Henderson, 3.22 per cent.; McLean, 3.27 per cent.; Muhlenberg, 3.31 per cent.; Hopkins,

Jan 1, 1920

Manganese Resources in Relation to Domestic Consumption Discussion of paper by JOHN V. W. REYNDERS, presented at the Cleveland Meeting and issued, as Pamphlet No. 1656-C, with MINING AND METALLURGY, May, 1927. A. G. BETTS, Kinderhook, N. Y. (written discussion).-When a business concern hires an office boy, it takes on the first bright-appearing young chap to apply and pays him the prevailing rate of wages. One of the chief tasks the .office boy is supposed to be competent to perform, is to clean out the office. The manager of the business is highly competent in many lines, but for some reason lacks the ability to keep the office clean. To the steel man, it would seem that manganese is the office boy, and it is purchased just as found and offered to the purchasing agent. The steel mill is competent to perform many functions on a grand scale and with wonderful efficiency, but it is unable to make real steel. It is the function of the office boy, manganese, to do this. It is open to serious doubt if steel mill operators have ever taken seriously the metallurgy of the preparation of crude manganese. It has merely been found that some usable crude manganese may be obtained by running certain manganese ores through an iron furnace when not busy on anything else, or remote from iron ore, or with a lining that is about gone. It is, however, an entirely unwarranted assumption that the metallurgy of manganese has been worked out, or that the supplies of usable raw ore must be limited to materials of some specified analysis. There was a time when ores of copper, lead and zinc, for example, had to be rich and of specified analysis, to be usable, but the commercial raw materials of today bear little resemblance to such ores of the past. The discussions of manganese that I have seen are based on the assumption that the metallurgy of manganese is fully established and that the only usable manganese raw materials are of the kind used today. These discussions contain another error, not so much of statement, but of implication-that the tonnages of manganese materials in the United States are so much in this state and so much in that. When it requires a period of years and the expenditure of millions of dollars for a competent mining company to explore thoroughly a few acres of mining ground, is it not absurd to say that there are so many hundred tons of manganese ore in a certain state? This fact is not apt to be known fully in 10,000, years. I do not charge the mining engineers. who are on record, of making misstatements, because they merely say that so much

Jan 5, 1927

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda&apos;s crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

By Walter Miller

Although confident of its ability to meet any demands that may be made, the petroleum-refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full cooperative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor in full harmony with the nation&apos;s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned. Refining, by constant study and development, by willingness to experiment and install new processes, and to replace older plants with more efficient equipment, had kept on a high plane of efficiency and progress. Working under the free competitive system, it built up its establishments until, as expressed in last year&apos;s report, it was easily able to supply any domestic demand that might be placed on it. Turning the United States into the arsenal not only of itself but of the united nations resisting aggression, however, in- creased the call for practically all petroleum products and in particular 100-octane aviation gasoline and high-viscosity aviation lubricating oils. Refining Capacity With over four million barrels a day of crude oil being charged to stills at the year&apos;s end, oil refining had broken all records and faced the necessity of further increasing its size to supply the ever-increasing demand for products, some of which, like 100-octane aviation gasoline, were research laboratory curiosities a few years ago. Although the refining capacity of the United States is listed at 4,860,000 bbl., about 800,000 bbl. of this is economically unavailable because of plant location or type. To meet the increasing needs, additional capacity of another half million barrels may have to be built in suitable locations and designed with an eye toward maximum production of aviation gasoline but with inherent flexibility to make it possible to vary and interchange with production of motor gasoline, furnace oils, and other products as necessity dictates. An interesting side light on this refining capacity question was an enquiry from official Washington for knowledge as to any idle refineries of something of the order of 10,000-bbl. daily crude capacity that might be purchased for bodily removal to Russia. 100-Octane Aviation Gasoline Largest of the tasks confronting refiners at the year&apos;s end was that of raising

Jan 1, 1942

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall&apos;s statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall&apos;s statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By Walter Miller

Although confident of its ability to meet any demands that may be made, the petroleum-refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full cooperative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor in full harmony with the nation&apos;s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned. Refining, by constant study and development, by willingness to experiment and install new processes, and to replace older plants with more efficient equipment, had kept on a high plane of efficiency and progress. Working under the free competitive system, it built up its establishments until, as expressed in last year&apos;s report, it was easily able to supply any domestic demand that might be placed on it. Turning the United States into the arsenal not only of itself but of the united nations resisting aggression, however, in- creased the call for practically all petroleum products and in particular 100-octane aviation gasoline and high-viscosity aviation lubricating oils. Refining Capacity With over four million barrels a day of crude oil being charged to stills at the year&apos;s end, oil refining had broken all records and faced the necessity of further increasing its size to supply the ever-increasing demand for products, some of which, like 100-octane aviation gasoline, were research laboratory curiosities a few years ago. Although the refining capacity of the United States is listed at 4,860,000 bbl., about 800,000 bbl. of this is economically unavailable because of plant location or type. To meet the increasing needs, additional capacity of another half million barrels may have to be built in suitable locations and designed with an eye toward maximum production of aviation gasoline but with inherent flexibility to make it possible to vary and interchange with production of motor gasoline, furnace oils, and other products as necessity dictates. An interesting side light on this refining capacity question was an enquiry from official Washington for knowledge as to any idle refineries of something of the order of 10,000-bbl. daily crude capacity that might be purchased for bodily removal to Russia. 100-Octane Aviation Gasoline Largest of the tasks confronting refiners at the year&apos;s end was that of raising

Jan 1, 1942

By Leo B. Bicher, Donald L. Katz

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC&apos;s original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By L. G. Jones

The objective of this paper is to present a better method for determining reservoir reserves of gas from extended drawdown test data. Means are proposed for conducting the test with or without the requirement of prior build-up to a static reservoir pressure. The test is based upon solutions to unsteady-state gas flow developed in an earlier paper and is believed to be superior to previous methods for determining reserves from flow-test data. The limitatiom of such tests are discussed, with emphasis on the subject of test duration. The test can supply useful information if the mechanics and limitations of it are understood. This type of information can be particularly valuable in deciding whether or not to drill offsets to producing wells. INTRODUCTION In the life of any gas or oil field, the engineer in charge must decide if certain wells need stimulation and whether or not to drill more wells in the field. Well production tests can aid in making these decisions. For instance, the value of stimulation can be estimated by determining formation permeability and the amount of well damage from drawdown or build-up tests. These tests are freely used in the oil industry. A less well-known type of analysis uses data from extended drawdown tests for determining reservoir reserves. Into this category fits the "reservoir limit test" of Jones,&apos;-3 and the "reservoir reserve test" presented in this paper. The chief value of these tests is their ability to "see" reservoir boundaries and thus prevent costly dry holes. Methods for determining reserves of both gas and oil reservoirs were proposed in the work of Jones. His proposals appear sound for single-phase liquid flow. The generality of his work on gas flow is open to question, however, since the analysis is based upon solutions to liquid-flow equations. The test for gas reserves presented here is derived from unsteady-state gas-flow solutions presented in a previous paper.&apos; In deriving this reservoir reserve test, it has been assumed that all of the reservoir energy is provided by expansion of the reservoir fluid and that the reservoir is radially symmetrical. No mention has been made of the effects of deviations from Darcy&apos;s law such as quadratic (turbulent) flow and well damage. Since the terms representing these effects are function of rate only, since the rate is constant and since the data are plotted in a differential form, it seems reasonable that these terms will not affect the test results in any way. No attempt has been made to estimate the effects of water drive, faults, or other departures from an idealized and isolated reservoir. For a qualitative discussion of some of these effects, the reader is referred to a paper by Jones3

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire&apos;s location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.