Search Documents

By E. William Rossi, Sean Gallagher, Richard L. Unger

The purpose of this study was to examine the lifting capacity of low-seam coal miners in four restricted work postures (roof heights of 36", 40", 44", and 48"), investigate the associated metabolic costs, and to examine electromyographic (EMG) data from eight trunk muscles during the lifting procedure. Subjects were thirteen underground miners accustomed to handling materials in restricted work postures. Each subject performed two twenty-minute periods of asymnetric lifting in each of four postures during the day of testing. The. frequency of lifting was 10 lifts per minute. A specially designed lifting box incorporated microswitches in one handle of the box and another in the bottom of the box, in order to examine the trunk muscle function at specific points during the lfting cycle. The data collected will be used by the Bureau of Mines to make recommendations for lifting materials in low-seam coal mines.

By S. A. TAYLOR

THE aftermath of a world war brings up a number of economic problems for the consideration of all thinking and patriotic citizens. The solution of the problems which confront the country at this time cannot well be accomplished by reference to past experience, for such conditions as confront us today have not existed in the past. We must, therefore, in any attempt to solve the present problems, rely to a great extent upon a careful analysis of present conditions to determine what is wrong; and after this is determined, seek the remedy and apply it. It needs no argument to establish the fact that, in the effort to win the war, the cost of so doing, and the waste in connection with it were, to a large extent, lost sight of; and this situation caused high wages, high cost of all materials, and of food supplies.

Jan 1, 1921

By Chris Joyce, Peter Ryan, Graeme Mcllveen

This paper briefly summarizes regulatory procedures and government agency roles and jurisdictions in each Australian State and Territory. The role of the Commonwealth of Australia and selected current trends in environmental regulation are also discussed. While the Commonwealth has played an active role in regulating specific commodities or mines through its powers over export licences, international heritage agreements and the Territories, such cases have largely been a result of response to specific public issues. This may change; the Commonwealth has established the Resources Assessment Commission and is canvassing the establishment of an Environmental Protection Act, aimed at the standardization of environmental standards through the creation of an Environmental Protection Authority. While the States, the Northern Territory and the Commonwealth lwve nominally different resource planning, environmental project approval and operational regulatory authoritit:s, the fundamental principles hinge on mining lease, planning and pollution control approvals.

Jan 1, 1991

During the year 1915-16, the Mining Engineering Society of the, Massachusetts Institute of, Technology had five meetings, at which the following gentlemen addressed the society on the subjects Mentioned: Professor Richards-Memory and the Business World. Mr. Hutchinson-Mine Examinations. Mr. Packard-Mining Law, Necessity of Amendment. Mr. A. H. Rogers-Organization of Mining. Property. Mr. C. Hurter-Explosives. Mr. W. Macgregor-Organization of a Gold Mine and Mill. During the year 24 new members were admitted, making the present active membership 54. There was an average attendance of 34 members at the meetings. HAIG N. SOLAKIAN, Secretary, 1915-16. The Pick and Shovel Club, Case School of Applied Science, has elected the following officers for the current year: President, G: D. Welty, Secretary, C. E. David, Vice-President, E. G. Hollman, Historian, L. S. Kuehn, Treasurer, C. E. Althouse, Sergeant at-Arms, H. H. Smith.

Jan 2, 1917

By Myles G. Hyams

A mining project is proposed for the state of Pahang, Malaysia. The proposal involves the mining of a sulphidic ore body and initial processing to form a sulphide concentrate which will be transported to a roaster/acid plant for the production of sulphuric acid. An outline is presented on the potential environmental impacts of the project which have been assessed by superimposing project infrastructure and processes on to the physical, biological and social environment during the early design and planning stage of the project. The potential impacts eliminated by engineering design and the techniques employed are presented. However, there are a number of potential impacts that require careful consideration and planning for long term management. These include surface water drainage, waste rock leachate, tailings disposal and the social environment. Environmental management designed to minimise or alleviate these impacts as a result of project implementation concludes the paper.

Jan 1, 1991

By S. Whinery

I am indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of

Jan 1, 1913

By Thomas Mucho, Anthony Iannacchione

This marks the 100th year that the aggregate industry has been served by a national association. Of all the accomplishments this longstanding relationship has achieved, there is probably none greater than the progress made, in worker safety. Perhaps the best way to measure this success is to examine injury trends in the aggregate miner population. For example, in the first half of the 20th [ ] century, 16 quarry mining disasters (a "disaster" is an incident with five or more fatalities) claimed 157 miners between 1909 and 1952. The largest of these was the disaster at the Sandts Eddy Limestone Quarry near Allentown, Pa., on March 26, 1942, where 31 miners died of asphyxiation by fumes/explosion. Thankfully, no mining disasters have occurred in the aggregate industry since 1952. It is these kinds of information that help us characterize improvements in aggregate worker safety over the last 100 years.

Jan 1, 2003

By S. Siddiqua

Diffusion is known to be the main transport mechanism of contaminants in fine-gained soils. To date, it is still common practice to estimate contaminant migration in the Bangkok Clay by means of pure advection models. A series of experiments with various chemical species was performed to determine transport parameters such as the diffusion coefficients and the distribution coefficients. The soil used was saturated undisturbed Soft Bangkok Clay. Column experiments were utilized in a number of laboratory tests involving advective-diffusive migration. Effective diffusion coefficients of different ions were back calculated from the test results. The distribution coefficients were determined from the results of the column tests and batch test. The results indicate that the evaluated parameters are in the range of values obtained from other researchers on similar kinds of soil. Based on this results contaminant migration by diffusion in the Soft Bangkok Clay can now be performed.

Jan 1, 2005

By K. R. Vost

Most theoretical methods for the prediction of air-temperature gradients in underground airways always assume that the temperature of the entering air either remains constant or has only a slow seasonal variation. Large changes of temperature, caused by variations in atmospheric conditions on the surface, were measured in a fourteen-day period in air entering a horizontal airway. The changes in wet-bulb temperature were damped along the airway less uniformly than the dry-bulb changes; significant variations occurred in the wet-bulb temperature of the air leaving the airway. The damping was .associated with large variations in air-temperature gradients. Other causes of rapid changes In temperature are discussed. These changes must be taken into account in predictions of the frequency with which undesirable conditions can be exceeded at critical points in the ventilation circuit of a mine to allow proper planning of ventilation and refrigeration requirements.

Jan 1, 1977

The twenty-fifth regular meeting of the Rocky Mountain Coal Mining Institute was called to order at 11 a. m. Monday, August 29, 1927, in the County Court House at Trinidad, Colorado, the Vice-President, F. L. Peart, presiding. After a few words from John F. Carmody, Editor of Goal Age, J. Q. McNatt, Division Engineer of the Colorado Fuel & Iron Company, read a paper on "Coal Geology." In the afternoon, Prof. C. B. Carpenter, of the Colorado School of Mines talked on the work in Fuel Engineering being developed at the Colorado School of Mines. W. C. Holman, of the Phelps Dodge Corporation, then read his paper on "Developing a Pit Car Design." L. M. Kuhns, Safety Engineer of the Gallup American Coal Company, read his paper on "Safety Methods at Gallup American No. 5 Mine." After discussion the meeting adjourned for the day.

Jan 1, 1927

There are no data available of shipments until 1858, and then estimated, when railroad service became available. By reason of the iron made in the county, and the large amounts of salt, the tonnage used locally was quite large, and until 1860 these are estimated from the probable salt and iron production. After 1859 the tonnages shipped by rail are partly estimated from the total shipments of the Allegheny Valley Railroad from four counties. It is believed that the totals are below, rather than above, what the actual production was. While considerably larger for the same years than figures given by the Secretary of Internal Affairs and census reports, these data were always too low in those days, partly because of lack of facilities for gathering them, but more largely because of the strong prejudice existing in those days against furnishing such data to any governmental agencies.

Jan 1, 1942

By Xiao Huang, Jean-Francois Thibault, Ali Merati, Prakash C. Patnaik

Single-crystal nickel-based superalloys are the current state-of-the-art technology for the manufacture of turbine blades. This technological improvement of the turbine blade has brought a considerable increase in its cost. Repair and overhaul of service stressed single crystal turbine components is an economic necessity for life cycle cost reduction of engines since the cost associated with replacement is significantly higher than its counterpart polycrystalline component. This paper will first review the recently reported research in developing repair technologies used for DS and SX components. These techniques repair the crack or defect while at the same time ensuring that the mechanical properties do not deteriorate and, more importantly, that the single-crystal microstructure is not jeopardized. It will then be followed by a brief overview of the research conducted and initiated by the authors with regards to the repair of single crystal alloys.

Jan 1, 2004

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special ,weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1917

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special ,weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1917

1 Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc , may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its president and its secretary, may be published in MINING AND METALLURGY or the Directory of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way 2 Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special weight with the Membership Committee of the Institute, in its consideration of the pro¬posal of a candidate for membership

Jan 1, 1923

By John V. Beall

TOO early spring may be the explanation for the poor turnout of mining and metallurgical engineer candidates at a large New York guidance conference, but it would be wiser to take a more serious view of this occurrence. Held a few weeks ago, the meeting was preceded by weeks of preparation and publicity in which many engineering societies participated. The meeting was the First Greater New York University downtown campus for splitting up anticipated to draw about 20,000 high school students from the New York area and environs. Seven of the theatres in the Paramount chain were avail- able to hold the audience for a panel program on career opportunities which was to be televised and piped into the theatres. Following the morning theatre session, students were to adjourn to the New York University downtown campus for splitting up into workshop sessions devoted to seventeen different branches-of the profession.

Jan 5, 1953

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By E. O. Fromm, R. I. Jaffee, R. M. Evans

IN connection with a research on gallium alloys, a method for the thermal analysis of very low melting alloys was developed, which appeared to be worthy of more than passing interest. As used, the method was suitable for work in the temperature range, — 72° to 250°C. However, with suitable adjustment, the method could be adapted for use over broader temperature ranges. The Rosenhain temperature gradient furnace,' adapted for low-temperature use, was the basis for the method. The gradient was set up in a stainless steel tube. The specimens were lowered through it at a constant rate while time-temperature or inverse rate data were taken. It was essential to maintain careful control of the top and bottom temperatures of the gradient. Also essential was good heat transfer from the walls to the specimen. This was accomplished by a liquid heat-transfer medium.

Jan 1, 1953