Search Documents

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By Robert B. Parsons

"The Canadian tax treatment of mining operations outside Canada is not as attractive as the treatment of Canadian operations. Further, the Canadian company that invests abroad a host of complex rules. This month, Tax Notes examines some of the major Canadian tax considerations confronting the Canadian company that wants to invest abroad. IntroductionCanadian-based mining companies are investing abroad more than ever before. These foreign investments trigger a complex set of tax rules that are distinct from the rules that apply to Canadian investments. In most cases, careful tax planning is mandatory if the company's tax liabilities are to be minimized. This article summarizes the main tax considerations that need to be taken into account with respect to a mining investment outside Canada.Branch Versus SubsidiaryOne of the first questions that arises in connection with a prospective foreign investment is ""Should we invest directly (that is, in a branch operation), or should we invest through a foreign subsidiary?"". In the case of a branch operation, the Canadian company owns and operates the business directly - that is, the foreign business assets are part of the Canadian legal entity. In the case of a foreign subsidiary, the foreign business operation is owned and managed by that subsidiary. The tax treatment of a branch and a subsidiary can be quite different."

Jan 1, 1994

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By M. R. Meyer, W. T. Walter

A great deal is known, in a qualitative sense, about the performance of CMI EB-36 centrifuges. The manufacturer can give reliable guidance for the proper operation of its centrifuges and can give general estimates of expected product moisture and recovery. Quantitative estimates of the effects of changes in the various operating parameters are more difficult to find. The engineer faced with designing a preparation plant may be without the specific data needed to make decisions. For example, to obtain optimum product moisture when drying 9.5 mm X 595 µm (0.4 in. x 28 mesh) coal the centrifuge manufacturer recommends having no more than 5% -595 µm (-28 mesh) material in the centrifuge feed. They know that more -595 µm (-28 mesh)material in the feed will cause higher product moistures, but they usually cannot quantify the increased moisture or describe the shape of the product moisture versus -595 µm (-28 mesh) in the feed curve. This study was conceived to provide quantitative information on the EB-36 centrifuges, focusing on product moisture, recovery, and size degradation. All of the centrifuges tested were Model EB-36 dryers from Centrifugal and Mechanical Industries Inc. (CMI), with feeds in the nominal 9.5 mm x 595 pm (0.4 in. x 28 mesh) range. These are typical centrifugal dryers in this application, and many were available for testing.

Jan 1, 1984

By Kaixi Jiang, Lei Zhang, Sanping Liu, Yufang Wang, Xiaoping Zou

"Molybdenite concentrates are usually treated by roasting, but low concentration SO2 pollution is a problem. Extraction of molybdenum and rhenium from molybdenite concentrates with a pressure oxidative leaching (POX) and solvent extraction (SX) process was studied. A series of POX-SX laboratory and pilot tests were carried out on the molybdenite concentrate. In the POX stage, more than 95% rhenium and 15-20% molybdenum were leached into solution. Solvent extraction recovered the rhenium and molybdenum from the POX solution. The extraction rates of Re and Mo were above 98%. The loaded organic reagent is stripped with ammonia. The stripping ratio of Mo is more than 98%. Compared to the roasting process, the total recovery of Mo increased from 93% to 97%, and Re from 60% to 90%. In the coming five years, POX-SX technology will be competitive in China.IntroductionMolybdenite is the main resource for the production of molybdenum, and about 99% of the total molybdenum was extracted from molybdenite. Rhenium is one of the important new materials in national defense, space flights, nuclear energy and electronics, because of its high melting point, high strength, plastic properties and significant creep resistance. There are no single rhenium ores in the world; rhenium mainly co-exists with molybdenum. Consequently, molybdenite is also the main resource for the extraction of rhenium."

Jan 1, 2012

By W. R. Phibbs

The blast furnace of the Columbia Steel Corpn., at Ironton, Utah, was put in blast April 30, 1024, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PeR Cent. Moisture................................................. 3.90 Volatile.................................................. 39.00 Fixed carbon............................................ 51.10 Ash............................................... 6.00 Sulfur................................................. 1.07 The analysis of the coke is: PeR Cent. Volatile.................................................. 0.55 Fixed carbon............................................. 89.70 Ash...................................................... 9.75 Sulfur................................................... 1.05 The coke is light and of a fingery construction, but is very fast burning. A screen test of the coke as loaded into the skip tubs at the furnace shows the following: Per Cent. On 2 in.................................................. 17.90 On 11/2 in................................................ 41.78 On 1 in.................................................. 27.80 Through 1 in............................................. 12.52 The by-product yields are as follows: Gas................................. 11,000 cu. ft. per ton of coal Sulfate............................... 30 Ib. per ton of coal Tar.................................. 12.65 gal. per ton of coal Motor fuel........................... 3.00 gal. per ton of coal Average B. t. u. in gas................. 567

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By Joshua Micah Hoffman, Catherine E. Johnson

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. One potential area from which future talent can be recruited is local student chapters. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements, there is a trend of job placement primarily in the engineering industry. Before the explosives industry can begin to compete with other industries, it should be determined what is drawing the students into these other fields. The work presented in this paper sought to better understand the collegiate student population from which a portion of future explosives professionals will emerge. This was done through the use of an anonymous online survey distributed to the student members of the International Society of Explosives Engineers, as well as, members of SEE student chapters. The survey contained questions about future job and career plans, ideal job placement, and expectations of salary. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry. This information can help steer recruitment activities and job offers. Through understanding what is incentivizing these students who have accepted or plan to accept jobs in other industries the explosives industry can better posture itself to be more competitive in recruiting from the collegiate talent pool.

Jan 1, 2014

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

By Alva L. Kuestemeyer, Randall J. Scott

INTRODUCTION Pincock, Allen & Bolt, Inc. (PAH) has developed a series of cost models for Western U.S. Gold Mines. The models indicate the economic potential of developing gold properties at various production rates and ore grades. Various combinations of mining and processing methods are also analyzed. The conclusions shown in this paper are taken from PAH's 600 page study titled, "Capital and Operating Cost Models for Western U.S. Gold Mines." PAH decided to develop the cost manual as a result of our perception of the industry's need for such a document. It was our impression that exploration development decisions were being made on the basis of limited economic information. PAH has compiled a substantial database on unit cost information. That database and the engineering capabilities of the firm allowed us to develop a reasonably detailed analysis of capital and operating costs and overall development economics. The study has developed a series of algorithms for underground and open pit mining, processing, G&A, and infrastructure costs. The capital and operating cost data served as a basis for performing after tax discounted cash flow analysis for the various development alternatives. For the base case scenarios, a 15% DCFROR was assumed and the required ore grade was back calculated using the computer. The ore grade versus production rate graphs summarize the economics of developing gold projects in the Western U.S.

Jan 1, 1987

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974

By Robert S. Mayo

Tunneling, for transportation, began in France with the Milpass Tunnel on the Lanquedoc Canal in 1680. Of course, the ancient miners had been driving tunnels in search of minerals since the dawn of history but this Milpas Tunnel was the first tunnel exclusively for transportation. In England in 1760, the Duke of Bridgewater opened a canal from his coal mines to Manchester, 10 1/2 miles away. At the mine, he drove a tunnel into the mountain so that the miners could shovel the coal directly into canal boats. James Brindley, an untutored genius, was his engineer and this whole transportation system was an instant success and very profitable through the years. Within a dozen years the Duke, again with James Brindley, opened up the Grand Trunk Canal, 139 miles in length with five tunnels. There was one major tunnel on this system, the First Harecastle Tunnel, 1 1/2 miles in length. But this tunnel was too small. It was only large enough for one 7-ft wide boat which had to be "legged" through by boatmen laying on their backs. By 1824 a second tunnel was driven parallel to the first one, but it had a towpath through it for horse haulage. This was the beginning of the " Industrial Age" and tunnels became a very important part of that era.

Jan 1, 1979

By K. Thirumalai, D. P. Schlick

Longwall Technology has a potential of resulting in safety and productivity improvements of U.S. underground coal mining similar to those experienced by the introduction of continuous miner systems. The study presents a comprehensive national evaluation of longwall technology to assess the potential of longwalls to improve health and safety and coal productivity. The study was conducted by the authors during the spring of 1980 as part of MSHA New Technology Coordination activities and with a view to examine the factors that may limit the acceptance of longwall technology in the U.S. coal mining operations. The study points out areas where adjustments need to be made in MSHA regulations and enforcement to help Longwalls. A two-entry longwall system appears to offer a practical method of improving underground coal productivity and safety. Applying regulations that are primarily designed for room and pillar methods to longwall mining, in some instances, reduces the effectiveness and productivity benefits feasible by new technology application. Controlling dust is the single predominant problem in the design and operation of longwalls in the United States. The results of this study points out a need for a coordinated program between government and industries on dust control technologies for examining acceptable technological options to control dust in longwalls without restraining the production capability of the system.

Jan 1, 1981

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

By Jennifer Pakula

Productivity improvements in underground mining are becoming harder to find. Most mines quickly identify deficiencies in their processes and then struggle to make productivity gains beyond that plateau. One way to increase productivity in this situation is to modify existing methods of operation. Vale?s Stobie Mine has been in operation since the late 1800?s employing a variety of mining methods. Many mining advances have been incorporated over time. With the advent of mechanized rubber tired equipment, sublevel cave mining was introduced to allow economic extraction of a large low grade area. Additional productivity gains were seen in the sublevel cave area with the introduction of preloading production drill holes. In preloading, the holes are loaded with bulk emulsion ahead of the production cycle and then primed for blasting as needed. The introduction of preloading, although giving the Stobie sublevel cave process an overall productivity gain, saw an increase in oversize due to the collar priming technique employed. Handling oversize material prohibited the operators from handling additional units of optimally sized material. Prepriming, adding detonators at the toe and midcolumn of the production holes during the preloading process, was identified as a change that could reduce the formation of oversize. This paper describes the introduction of prepriming to the sublevel cave mining method and focuses on the process Stobie employees followed to ensure a safe transition to this productivity improvement.

Nov 1, 2011

By Milton C. Head, Aulton E. Roland, William E. Hawes

INTRODUCTION Uranium mining in the Grants Mineral Belt has undergone changes from methods pioneered during the 1950's and has now become fairly standardized throughout the district. The orebodies vary in size and shape and have been most successfully mined by using modified room and pillar methods with pillar recovery. This paper will expand on methods and equipment that are being used and modifications of these that will increase productivity and efficiency. GEOLOGICAL BACKGROUND The petrology of the Grants Mineral Belt consists of alternating layers of sandstone and shales (mudstone), with occasional thin layers of coal. The sandstones are aquifers which are generally artesian to some extent. The shales are bentonitic and decompose into extremely sloppy mud when exposed to water. Figure 1 shows a typical geologic section. Most of the uranium produced in the Grants Mineral Belt comes from the Westwater Canyon member of the Morrison Formation and occurs as scattered ore bodies throughout the formation. This formation consists of layers of bentonitic shale and sandstone of varying degrees' of cementing and grain size. It is also a very significant artesian aquifer. The unconfined compressive strength of the various formations is not high, as shown in Table I. It is important to note that these represent average values and a great range may exist within a single formation, especially In the Westwater which is the ore formation. [ ]

Jan 1, 1982

By Philip D. Pearson

Competition is the problem and modernization is the solution in today's underground iron operations on the Lake Superior Range. Profound changes in the iron ore picture during recent years have prompted correspondingly great changes in the economic position of the Lake Superior underground mines. To meet the ever growing competition from other lower cost iron sources, underground operators are becoming increasingly aware that the newest advancements in mining technology must be incorporated in their operations. UNDERGROUND POSITION TODAY The extraction of iron ore by underground methods has been going on for many decades in the Lake Superior region, starting in 1872 on the Menominee Range. The number of mines has changed gradually over the years as new ones were opened and old ones were exhausted, but in recent years, the most drastic change occurred from 1960 to 1961. In 1960, there were 31 underground mines operating in Michigan, Minnesota and Wisconsin, but at one period in 1961 only 20 were operating (Table I). In western Ontario so far there has been only some temporary curtailment of operations. Of the 11 U.S. mines which ceased operations in 1961, some may he closed only temporarily, but some will remain closed for our lifetime, at 'east, unless there is a tremendous reversal of the present trend in the iron ore market

Jan 3, 1962

By J. C. Draper

Duquesne Light Co.'s Portal No. 3 mine, in the Warwick group of mines in Southwestern Pennsylvania, was started in June 1965 with battery- powered tractor-trailer face haulage. The area as- signed to Portal No. 3 encompasses over 8000 acres of coal and will be developed by driving a set of main entries through the center of the tract in roughly a westerly direction, and sub mains on a 45º deflection angle in roughly a northerly direction (Figs 1 & 2). In the original planning these sub mains were to be at a 90º angle with the mains, but difficult roof conditions necessitated a change in plans. The entries and crosscuts are driven 18 ft wide in the normal Sewickley seam which varies between 46 and 56 in. high. The mine bottom is a strong shale and in average, cool or dry outside conditions stands up well for rubber-tired haulage equipment, but when the outside conditions are hot and humid, the bottom becomes soft and muddy. This condition lessens as the mine faces are advanced further from the portals because the condensation will then take place principally on the surfaces of intake entries outby the working areas. To aid the situation, an air cooling system was installed and is used as conditions dictate.

Jan 7, 1968

By John Clarke Holman

Industrial growth and survival in today's competitive world means both economic efficiency and technological superiority. Superior technology includes not only exploiting the best methodologies and techniques presently available, but also a continuous search for and development of, better ones. In practical terms this translates into an investment of substantial sums of money. Of course, even a relatively small investment will not be justified if the fruits of the project cannot be secured to the investor and the inventor alike. There are at least three ways to protect new or improved technology. If the improvement reaches the height of an invention, "patenting" usually is the preferred mode of protection. If, however, the improvement is novel and valuable but does not satisfy the requirements of the patent laws, one may then consider "trade secret" agreements as a means of obtaining appropriate return for the investment made so long as the improvement is capable of being maintained in secret and cannot be "reverse engineered." If one develops a new and useful organism and seeks immediate protection from infringers, current thinking is that the copyright law may afford such protection simply by publishing the genetic code. Here is one instance where you may publish without perishing! This paper will endeavor to highlight the pros and cons of various legal mechanisms and their applicability to the frontiers of technology.

Jan 1, 1985

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989