Search Documents

By Jin Liu, Torstein A. Utigard

At its Copper Cliff Smelter, Vale Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. Coke supplies a minor proportion of the process heat requirements, limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Extensive experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. The introduction and description of the experimental set up were given in Part 1 of this paper and an early paper published in Yazawa symposium1 together with the results and some in depth discussion on metallurgy. This paper intends to discuss the kinetics of the miniplant flash furnace testwork.

Jan 1, 2015

By R. V. Higgins

Many contributions to methods of forecasting the performance of waterfloods of a five-spot pattern have been made by investigators. In most of these forecasting methods, a previously selected sweep efficiency is used, and other simplifying assumptions are employed to obtain the objective. In this paper the calculated oil recoveries from several five-spot single- and multiple-layer stratified reservoirs were made with a minimum of assumptions, and because of the techniques used, no previously selected sweep efficiency was required. As a result, the accuracy of the forecast is increased. Permeability curves and continuously changing saturation gradients are used in every section of the pattern. By means of a potentiometric model, the flood pattern is divided into channels, the centers of which are the streamlines. The channels are divided into cells. As flood water enters, the permeability and saturation of each cell change with time. In this study the production from multiple-sand layers of different absolute permeability but with the same relative permeability-saturation relations are combined. The results are shown for a single- and 10-layer reservoir with a permeability variation of 0.60. The oil rate, water-oil ratio, and recovery are shown as functions of time for a 2- and 20-centipoise oil starting in primary phase and after fill-up.

Jan 1, 1962

By John J. Baz-Dresch

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel-powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the lVine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 2010

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By W. J. Blackstock

Introduction To The great majority of people, the term 'strip coal' has little or no meaning, or if it has any significance it is thought to refer to a poor grade of coal that had to be accepted during the war because no other fuel was available. Few people in the Province of Alberta realize the magnitude of our coal stripping industry, and fewer realize that strip coal has been available to domestic consumers for at least forty years. Among the first in the field of strip coal mining in Alberta were the Tofield Coal Company, Ltd., and Sterling Collieries Company Ltd. It was not until the advent of World War II, with its huge drain on industrial and domestic coal sup? plies produced by the underground mines, that some other source of coal was seriously sought. The tremendous shortage of manpower du ring this period of National emergency made it imperative that any increase in the coal production must be procured on a high tonnage per man-hour basis. It was therefore natural that the highly mechanized strip mine should be eagerly encouraged and subsidized by the Governmental agency - the Emergency Coal Production Board - under the very able direction of Mr. G. A. Vissac.

Jan 1, 1949

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By H. W. Brandt

A field test was designed to inject a specially formulated two compound epoxy resin into the roof rock ahead of a working face to cement fractures and formation interfaces at the Westmoreland Coal Co., Winding Gulf Div., Eccles No. 5 Mine, Eccles, West Virginia. Five 30 foot long X 2 inch diameter, hold were drilled at an angle of 15° above the plane of roof line front the face of a working entry. The epoxy resin compounds were pumped through a proportioning unit and mixed in-line before being discharged into the drill hole under treatment it injection pressures up to a maximum of 450 psig. When the coal face was advanced an anomalous failure of the roof rock occurred in the treated section. Further testing was suspended until the cause of the failure could he determined. The polymers were tested, under confined conditions, in 2 inch pipe columns. Extreme temperature and pressure (up to 2400 psig) rises were recorded as they cured, It was concluded that this pressure source fractured the rock and caused the roof failure. The entire program was terminated after it was determined that the heat rise and resultant high pressures could not he controlled chemically or mechanically.

Jan 1, 1978

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By Lanre M. Oshinowo, André Bakker

"An understanding of the parameters that govern the just-suspended impeller speed, Njs, and the distribution of solids, is critical to the efficient operation of hydrometallurgical and other processes involving solid-liquid suspensions. In this paper, the distribution of solids in stirred tanks under a range of solids loadings (0.5 to 50 vol%) was predicted using CFD and validated against experimental data obtained from the literature. The multiphase flow is modeled using the Eulerian Granular Multiphase model. This paper will also review the established design parameter Njs in the context of scale-up and compare it to the quality of solids dispersion as a means of assessing correct scale-up in suspension tank design. The results of this study will describe a straightforward procedure to obtaining comprehensive information about reactor behavior with complex CFD models.The performance of hydrofoil impellers and a 45° pitched-blade turbine at suspending solids under different agitation speeds was studied. Both single and dual impeller operation have been evaluated. The settled solids fraction for speeds below N js, and the cloud height for impeller speeds above Njs were predicted. The CFD predictions are in good agreement with experimental literature data on velocity distribution and cloud height."

Jan 1, 2001

By W B. Edgar, S C. Dominy

High-nugget effect vein-gold systems are generally considered to be one of the most challenging of deposit types to evaluate and exploit. To potential investors and mining companies, they are viewed as high risk because of the associated uncertainties in the grade estimate and general paucity of Ore Reserves at production start-up. However, despite the well-known risks, these deposits often have a grade upside that makes them potentially attractive. The reporting of resource grade is of importance and perhaps even more so is the reporting of the associated uncertainty attached to the grade estimate. The use of the grade estimate supported by a grade range is recommended to achieve more complete and useful disclosure. The definition of the grade range can be somewhat subjective, ranging from opinion based estimates through to data-based estimates and geostatistical conditional simulation. Whichever method used, the over-riding issue must be the provision of enough data of appropriate quality and full disclosure to the public of relevant uncertainties.CITATION:Dominy, S C and Edgar, W B, 2012. Approaches to reporting grade uncertainty in high-nugget gold vein projects, in Proceedings Project Evaluation 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Board for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy atmospheres which through neglect or accident might surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The third of these surveys covers conditions in Germany.

Jan 1, 1929

By G. Reuben Yourt

THIS paper is chiefly a description of the improvements in dust control chat have been brought about in the assay office grinding room at Wright-Hargreaves. The fume exhaust systems are briefly included because they also are important to the health of the employees. There are three chief factors which determine the efficiency of a dust control system: First, the amount of time and thought spent in designing it. Second, how close! y it is kept up to date with the growth of the plant-a system that is adequate for the number of machines operating when it is installed may fall short of fulfilling its purpose as the plant expands. Third, unless someone is held directly responsible, a system is likely to get out of repair and gradually lose its efficiency-this can easily be detected by regular dust surveys. In designing the present system at Wright-Hargreaves, the object kept in mind was to reduce the dust concentration of all operations to a safe limit, chat is, well under 300 particles per cubic centimecer of air. By doing this, a condition would be attained chat would make it possible to discontinue the use of respirators, which at best are not very comfortable and do not remove all of the hazardous fine-dust particles.

Jan 1, 1941

The Particulate Mineralogy Unit has been established at the College Park, Maryland, Metallurgy Research Center. The Particulate Mineralogy Unit will have the responsibility within the Bureau of Mines for the characterization of particulate minerals which have potential for adverse environmental effects. The Unit will provide a focal point for identifying particulates in connection with environmental problems related to the activities of agencies such as OSHA, HEW, EPA, and MESA. The Particulate Mineralogy Unit is seeking to clarify the ambiguities surrounding the mineralogy of and terminology used for asbestiform minerals and other mineral particles. The Unit?s investigations of the morphology, composition, and structure of asbestiform minerals and their nonasbestos analogs have made its members recognized experts in this field. The information which it develops on the characterization of asbestos and other particulate mineral forms such as silica should provide a technically rational basis for decisions by regulatory agencies. Those desiring further information, contact Dr. W. J. Campbell, Program Coordinator, College Park Metallurgy Research Center, College Park, MD 20740, telephone: 301-344-4014. ALUMINUM: For over a month, domestic producers have priced 99.5 percent grade primary aluminum ingot at 48¢ per pound. In the same period, merchants raised ingot quotes by 1.5¢-2.5¢ to a range approaching 44¢-47¢ per pound.

Jan 1, 1976

By W. L. Chong, Y. Zou

There are many types of Earth Retention Systems (ERS) available in the market where more than one method can be a feasible solution for a project. This paper examines the design and construct process of a project in Dee Why, NSW using a hybrid ERS comprising contiguous piles with jet grout infill. The development comprises a deep basement and mixed-use urban superstructure. The site is located in an area of variable ground conditions, high ground water table and in proximity to existing buildings with multi-level basements. This paper details a comprehensive assessment of the geological conditions and strategies adopted to better understand the effectiveness of the proposed product and to minimise the associated risks of the proposed solution. This involved conducting additional geotechnical investigation, extensive numerical modelling and in-situ monitoring of the movements and the performance of the walls. A monitoring regime consisting of inclinometers, survey points on capping beam and prisms on the neighbouring buildings and roads surrounding shoring wall was implemented. The monitoring results were back-analysed using computer software WALLAP, Plaxis–2D and Plaxis–3D for the post-construction examinations. This paper details the effectiveness and advantages of a hybrid ERS using contiguous piles with jet grout infill.

Nov 1, 2022

By E. J. Sides

In this paper, the argument is put forth that the codes used for public reporting of mineral resources and mineral reserves have some significant limitations with regard to the information provided to investors on the short- to medium-term value of mining properties. Such limitations include a) failure to explicitly incorporate a time element and b) failure to state explicitly the quantity and quality of mineral product that will be produced for sale. A time-value framework for reporting mineral assets is proposed in order to overcome these limitations. The proposed system is based on two classification axes: a) an X-axis representing time in years during which the value of the asset is likely to be realized and b) a Y-axis representing the value identified by a mining or exploration company\u2019s activities. The potential benefits of this system are discussed, including the ability to incorporate factors, such as permitting and construction times, directly into the magnitude of the reported mineral assets. The proposed framework would assist in the standardization of mineral assets reporting in such a manner that they could eventually be more readily included in financial statements. Year of Publication: Not explicitly mentioned in the document.

Jan 1, 2010

By Christopher Mark

Successful longwall gate entry design requires control of both vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses, which are generally tectonic in origin, can be highly destructive during the development and headgate phases of longwall mining. The goal of this paper is to present the current state-of-the-art in detecting and controlling horizontal stresses. The information presented was collected through site investigations at 45 U.S. longwalls and an international literature review. The paper begins with a discussion of the present knowledge of regional in situ stress fields in the U.S. A review of available underground stress measurements from coal mines is presented, along with data collected by structural and petroleum geologists. The combined evidence indicates that a persistent ENE-EW trending stressfield is present throughout the eastern coalfields. Experience with horizontal stress in longwall mines is addressed next. The paper focuses on the northern Appalachian region, where the effects of horizontal stress have been most evident. Three case histories are discussed in detail, and the solutions each developed are highlighted. Observations made in the Southern Appalachian, Alabama, and Illinois coalfields are also described.

Jan 1, 1991

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By Pratter P., Boley C.

Polymers are well established in geotechnical applications, for example in ground improvement, where the polymers act as a binder that, when cured, holds the grains together by adhesive and cohesive forces. The subject of this research work is an innovative composite of polymers and gravel, which differs from conventional grouting materials due to its adjustable material properties. With these specific properties, the semi-rigid material can be optimally adapted to the local ground conditions and the individual framework conditions of a construction project. For the characterization of the composite material, stateof- the-art methods, such as image processing by segmentation, are presented. Segmentation is suitable for quality assurance and monitoring of laboratory samples and soil samples directly from ground improvement on the construction site. The load-bearing capacity of the innovative material can even be increased to the order of magnitude of concrete. For this reason, the soil mechanical laboratory tests in this research had to be modified and even expanded by rock mechanical laboratory tests. Based on the experimental investigations, the importance of this innovative material for practical application is demonstrated by a calculation example from construction practice, which shows that even difficult ground conditions can be handled with it.

May 1, 2022

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022