Search Documents

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By J. G. Trowell, D. T. Magee

"IntroductionMANITOBA'S first recoverable oil was from the California Standard Daly 15-18 well in Lsd. 15, Sec. 18, Twp. 10, Range 27, W.P.M., completed early in 1951. This well also gave the first indications of commercial production in the Williston basin, which is centred in North Dakota and extends into southeastern Saskatchewan and southwestern Manitoba. Subsequent drilling in the Manitoba portion of the basin has revealed the presence of oil in more or less commercial quantities at various points in an area approximately four townships in width and eleven townships in length.Although completions are becoming fairlly widespread in the area,, the greatest activity is in the Virden district, with the focal point in the Daly field, approximately eight miles west •of Virden. This paper will deal with the various techniques used in the Daly field, where •completion problems have •been unusually troublesome. Techniques evolved there have already been used with success at other points in southwestern Manitoba.Daly FieldGeneralTo date, all production has been from the Mississippian limestone, which is encountered •at depths ranging from 2,300 to 2,500 feet. Pay thickness is •of the order of 100 feet. Core analyses indicate average porosity .of about 9 per cent but permeabilities, for the most part, are extremely low."

Jan 1, 1953

By W. L. Brown

"The Normetal mine is about 7 miles east of the Ontario-Quebec boundary, and 13 miles north of the town of Dupuy on the Canadian National railway. The mine workings are largely on lots 44 and 45 in the south half of range 10, Desmeloizes township.The surface outcrop is reported to have been discovered by a trapper previous to 1925, but the details are obscure. The property was originally owned by the Canadian Exploration Company of Amos, Quebec, and was later transferred to Abana Mines, Limited. The latter Company carried out underground work from two shafts down to the 550-foot level. The property was acquired by Normetal Mining Corporation in 1931 and was reopened in 1933, when development work was carried down to the 800-foot level. The mine was closed down in 1935 because metal prices did not justify production at that time. It was reopened early in 1937 and milling commenced in September of that year. To the end of 1945, a total of 1,497,- 169 tons of ore was milled from which was produced 184,533 tons of copper concentrates containing 84,738,368 lb. copper, 2,744,100 oz. silver, 26,230 oz. gold, and 153,524 tons of zinc concentrates containing 163,752,433 lb . zinc."

Jan 1, 1954

By Duclerc Fernandes Parra, Luis Filipe Carvalho Pedroso de Lima, Washington Luiz Oliani, Danilo Marin Fermino, Ademar Benevolo Lugao

The modified polypropylene was obtained from isotactic polypropylene (iPP) in spheres by irradiation with gamma rays in the presence of acetylene. A new morphology with distinct rheology is obtained by this process in which occurs: degradation, branching and/or crosslinking. The objective of this study was to investigate the effects of thermal aging on the crystallinity and morphology of the modified polypropylene, High Melt Strength Polypropylene (HMS-PP). The thermal stability was evaluated after aging of samples using a stove at temperature of 90 °C, in presence of air at different periods of time. Aging effects were characterized by: Thermogravimetry analysis (TG), Differential scanning calorimetry (DSC), Infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM). In thermooxidative conditions, the formation of oxidation products essentially involves a hydrogen abstraction by the peroxyl radical, leading to hydroperoxides as primary products and chemical degradation in the immediate crack tips. The effect of thermal degradation (chain scission and oxygen diffusion) on iPP was a more intense crack formation. Surface cracks increased with the aging time. In comparison of iPP, the modified PP samples had a morphological barrier inhibiting the penetration of oxygen into the sample and in consequence limit the propagation of degradation

Jan 1, 2015

By J. C. Nigro

The potential use of prereduced pellets in the burden of the blast furnace continues to be a topic of interest. Several excellent papers have been written describing the theoretical and experimental rewards. (1) (2) (3) (4) (5) (6) (7) (8) (9) Significant increases in iron output and substantial savings in coke consumption are major advantages over conventional iron oxide pellets. The savings are especially important in areas where good coking coal is at a premium. Lower handling and transportation costs may also be factors favoring prereduction. When considering the overall cost of making and smelting prereduced materials the optimum metallization level becomes significant. An analysis by Agarwal and Pratt of the thermodynamic aspects of blast furnace operation with all prereduced pellets shows that the criteria controlling coke consumption depends upon the degree of reduction and upon the percentage of oxygen (present as FeO) removed by solution loss.(8) The authors state that although the chances of obtaining large fuel savings are greatly improved when metallization is high, reduction to the highest degree, which is costly, may not result in the lowest energy requirement per ton of hot metal; thus, over reduction could possibly result in wasted energy in the blast furnace.

Jan 1, 1968

The Technical Programme Committee-Metals Technology of The South African Institute of Mining and Metallurgy, in association with its Vaal Triangle Branch, held a one-day colloquium on 18th April, 1989, the theme being 'Ferous Pyrometalurgy: A Challenge for South Africa'. The venue was the Auditorium 100 at the campus of the Vaal Triangle Technikon in Vanderbijlpark. Project and contract management A Project and Contract Management Conference is to be held on 19th and 20th September, 1989, at the C SIR, Pretoria. Powder metallurgy The PM 90 exhibition is to be held in Wembley, London, from 2nd to 6th July, 1990. The wide range of powders, processing machinery, and powder-metallurgy components at the exhibition will reflect the growth in this highly specialist industry. Castings and forgings Exhibition organizers, FMJ International Publications Ltd, are set to build upon the success of Castings & Forgings '88, which was held as a joint event with Pat- Cast '88. Castings & Forgings '89-with Pat-Cast '89- has already generated a high level of interest, which has been reflected in the demand for stands. Furnaces FURNACES '90, the eighth in this series of exhibitions for the thermal-processing industry, will be held in Solihul, West Midlands, England, on 6th and 7th March, 1990.

Jan 1, 1989

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

By Allan M. Hale

The central Florida phosphate industry is not a recent development. The first phosphate mining occurred in approximately 1888 (1). Many of the original mining companies were "wildcat" operations operated with rapid phosphate extraction as the sole purpose and no long-term commitment to development. Many of the early pioneers were ill-equipped to mine phosphate at either a practical or economical level; as a result many of these early companies "folded" after only a brief period of operation. However, as these early companies went out of business, several large companies developed, expanded their mining territories bought up the folding companies and by 1903 (little more than 10 years after the first mines were started), approximately 37 of the original 60 mines were control- led by three major companies (1). In the early period, mining reclamation was nonexistent. The mined out areas were left to revegetate and reclaim "naturally" over the period of many years. Reclamation practices were only started relatively recently and the various reclamation techniques developed and used in the past have continued to be employed with varying degrees of success through the present time. The reclamation techniques used in the past and currently include land and lakes restoration, sand tailing reclamation, slime ponds reclamation and overburden fill.

Jan 1, 1980

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By A. G. Kim

Increasing transportation costs, clean air regulations and the decreasing availability of landfill space are factors in the increased interest in the utilization of low cost disposal sites for coal combustion residues (CCR). Inactive surface and underground coal mines can satisfy the conditions for stable CCR disposal sites, and subsurface CCR injection can be beneficial in reducing the amount of acid mine drainage (AMD) often produced at such sites. The material is expected to add alkalinity to the subsurface environment and to decrease the permeability and porosity of the buried spoil. Both mechanisms can reduce the amount of acid normally generated at a mine site. The Bureau of Mines is cooperating with an independent coal company in a test of subsurface injection of a mixture of fly ash, from conventional power plants or from fluidized bed combustion (FBC) , with AMD sludge into a reclaimed surface mine. Changes in water quality parameters and the concentration of heavy metals in water samples from wells and seeps are being used to assess the effect of CCR injection. The preliminary results discussed here indicate that improvement in subsurface water quality was related to fly ash injection and that components of the fly ash were stable in the acid environment.

Jan 1, 1994

By Fleming, R. C.

ONE OF THE NEWEST developments of industry rising from the commercial application of scientific knowledge is in the making of solid carbon dioxide from the gas about 1925 the first efforts were made to manufacture "dry ice" on a large scale and at a price to permit widespread use. From that beginning the industry has grown to a consumption of 40,000 tons in 1930. Carbon-dioxide ice, as the name implies, is merely the gas compressed and cooled to a solid. The ice has a temperature of 109° F. below zero and is in many ways superior to water ice. It evaporates to a gaseous form so it is not wet and leaves no trace; in fact, one suggested minor use is as coasters under water glasses on the dining table. The gas is harmless except in large concentrations and. when the ice is used as a refrigerant, the resulting gas actually becomes a preservative, keeping oxygen away from perishable products. Not only does the ice have a greater amount of cold in a small volume than water ice but cooling is effected by direct contact of the resulting gas with the materials to be refrigerated rather than by convection air currents.

Jan 1, 1932

The present work aimed to verify the possibility of using froth flotation to separate the constitu-ent minerals of an alaskite rock waste having as the main minerals quartz and feldspar. Three stages of tests have been carried through. In the first stage was used an amphoteric collector for flotation, diaminedioleate, at pH 2 and, after analyzing the final products, a very poor selectivity was ob-served. During the second stage of tests, different collectors that are normally used for feldspar flo-tation as amines, sulfonates and soybean oil were employed. Once more, it was not possible to reach reasonably selective results. In the third stage, a salt of etheramine was used for collecting the feldspar and hydrofluoric acid was utilized for controlling the pH. A simulation of three flotation steps (rougher, cleaner and recleaner) permitted to attain a good selectivity in the flotation process. A concentrate with a silica content of 96.6% was obtained. The low concentrate content of alkalis totalizing 0.52% and a feldspar recovery of 96.5% to the tailings, represented by the high content of Na, K, and Al2O3 in the tailings, demonstrated that the concentrate was made up mostly of quartz.

Jan 1, 2014

By K. C. Ko

The pit slope angle dictates the economics as much as the depth of the pit. Steeper slope provides more ore reserves, at the same time, the steeper slope presents higher probability of instability and associated maintenance problems. While large open pit mines mostly belonged to nonferrous metals in the past, other mines are becoming deeper as the mine economics permits deeper mine operations, Such minerals include coal, uranium, phosphate, and others. There are some basic differences between an open pit slope and slopes that are encountered in usual civil engineering work such as dam embankments and highway cuts (Figure 1). The stability of the civil engineering slope changes continuously with time due to ground-water movements, weathering, etc. But the stability of the open pit slope (Figure 2) changes more drastically day-to-day or even hour-to-hour, These changes occur because not only is the slope geometry being continuously changed by the mining operation, but also different geology and geologic structures are being exposed on the slope. Even when a particular slope area is not presently being mined, excavation in adjacent areas can affect the general condition of that slope area. A pit will experience some slope failures during its life.

Jan 1, 1977

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981