Search Documents

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By D. G. Collins

As part of its effort to develop ways to maximize resource recovery, the Bureau of Mines investigated the extraction of vanadium from Western phosphate beneficiation tailings with H2S04 and/or H3P04. Dissolution of the vanadium was accomplished by digesting a mixture of acid and a 50-pet-solids, tailings-water slurry. In the most effective method investigated, vanadium and phosphorus were leached by digesting the slurry at a constant boiling temperature (1000-1100 C) in a stirred reactor. In batch tests, maximum vanadium dissolution was 95 pet. In continuous-circuit tests designed to further evaluate vanadium dissolution at con-stant boiling temperature in a continuously stirred reactor, vanadium dissolution ranged from 70 to 85 pet. An economic evaluation of the process demonstrated that H2S04 consumption is the major cost factor. Based on the value of the vanadium product with no allowance for a phos-phate product, the cost of producing the V205 is more than twice its value. The potential for profit would depend upon the value of the phosphate fertilizer produced from the impure H3P04 remaining after vanadium extraction.

Jan 1, 1985

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By J. P. Harrison, M. Grenon

"This paper summarizes the results of numerical studies on drift stability in moderately jointed rock masses. It investigates the relative pertinence of geomechanical factors such as joint orientation, spacing and stress regime. This is undertaken using a distinct element model and a series of parametric studies. IntroductionIn evaluating the stability of drifts in jointed rock, it is often necessary to compromise by employing models that capture the complexity of the rock mass, but which are still simple enough to allow for their routine implementation. The distinct element method can arguably provide an eloquent method to accomplish this. This paper explores the applicability of the method by means of a parametric study aiming to identify the dominant factors that influence the stability of drifts in moderately jointed rock. To this end a commercially available 2D distinct element numerical model was used. A series of techniques are presented in an effort to quantify the results of any instability predicted by the model.This paper also demonstrates a case study where a 3D joint network model was integrated into the distinct analysis software package. The advantages, as well as the current limitations of this approach, are discussed."

Jan 1, 2001

By Walter Valery, Kristy Duffy, Alex Jankovic, Peter Holtham

Hatch’s Mine to Process Optimization projects integrate mining and processing strategies, minimizing operating costs and maximizing overall profit. The methodology involves ore characterization, blast audits, plant surveys, analysis of historical data, and integrated modelling and simulation of mining and processing. Blast designs are tailored according to ore type and the downstream process is optimized for the changed feed. This approach has increased throughput and minimized costs for many operations worldwide. The implementation of this methodology at an iron ore operation that faced challenges with increasing mining strip ratio and ore body mineralogy changes is presented in this paper. The larger stripping ratio increased mining costs and constrained the run-of-mine (ROM) delivery to the process plant. Process performance was affected as the ore mineralogy shifted from predominantly hematite to include greater proportions of magnetite. The project objective was to minimize overall cost per ton mined and processed and maximize profit. Tailoring the blast designs according to ore type and process optimization increased the throughput of all process lines. This provided the potential to shut down one of the five processing line, aligning the mine and plant capacity and significantly reducing the processing costs.

Oct 3, 2019

By Godwin J. Igwe

For soil remediation technology to be effective, a thorough understanding of the interactions between a targeted contaminant and the soil matrix is crucial. Proper selection of remediation technology, based on understanding the bonding/binding characteristics of the soil and contaminant, can often result in significant remediation cost savings. Contaminated soil cleanup is complicated by both the physical nature of the soil formation and the behavior of contaminants introduced into the formation. Contaminants can exist in the subsurface in different phase attached to the soil surfaces, dissolved in the ground water, or occupying pore spaces as a separate gaseous or liquid phase. Contaminants properties and how they exist in the subsurface influence their toxicity, mobility and treatability with different remediation technologies A soil characterization study was performed to provide information for remediation technology selection for an inorganic lead contaminated soil. The soil pH, TCLP analysis, thermogravimetric analysis, the soluble anions and cations present, equilibrium leaching tests, analysis by x-ray fluorescence, sequential extractions and speciation analysis using scanning electron microscopy, were all used. Results provided many insights into contaminant behavior in the soil, indicating ultimately whether soil washing or solidification/ stabilization remediation technologies were applicable.

Jan 1, 1994

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013

By T. Langthaler, H. W. Engl, H. Holl, K. L. Schwaha

"The trend towards near net shape casting requires the development of more complex design and control algorithms for continuous casting ""machines in particular with respect to the solidification process.Compared to conventional continuous casting the reduction in casting thickness allows to influence more directly the solidification rate by control variables like surface cooling and/or casting speed.In order to enable the determination of these control variables for a given solidification profile, an algorithm (inverse solidification analysis) has been developed based on nonlinear constrained optimization. The application of the model is illustrated by practical examples ranging from conventional continuous casting to advanced thin slab casting.IntroductionProcess development in the Iron and Steel Industry is directed towards the realization of continuous process sequences. Since the direct linkage of processes imposes some restrictions onto the individual process steps, more complex algorithms are needed for design of equipment and control of operation. In particular the recent trend to reduce casting thickness, i.e. to cast thin slabs, has made the direct coupling of continuous casting and rolling absolutely necessary. The prospective development in strip production is schematically shown in fig. 1."

Jan 1, 1988

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By L. W. Kelly

The purpose of this paper is to indicate some of the benefits that have been derived in the Zeigler No. 3 mine by using roof bolts under extremely adverse roof conditions J with the thought that much better results could be obtained in other mines with more normal roof conditions by applying some of the practices that were developed in this mine. Some of the benefits that have been obtained in this mine, which will be shown in this paper, are: 1. Increased tonnage per man-shift at the face when roof bolts are used, as compared to the tonnage under similar conditions when conventional timbering methods were used. 2. Increased efficiency of roof bolting by giving the foremen a definite plan to follow. 3. Reduction in delays caused by failures of the trailing cables of loading, mining, and drilling machines. 4. Reduction in the number of accidents after roof bolting was adopted. Inasmuch as the success that followed roof bolting in this mine was obtained under one of the most treacherous roofs in the Middle West, it is reasonable to suppose that correspondingly better results could be obtained under more favorable roof conditions by using the same procedure.

Jan 1, 1952

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Norman L. Kotraba

Zia Metallurgical Processes, Inc. has developed and patented a steelmaking process capable of converting iron bearing metallurgical wastes into high quality steel products. The process utilizes a proprietary design rotary hearth furnace to convert iron bearing wastes, pelletized with coal, or other forms of carbon, into direct reduced iron (DRI). This DRI is fed, hot, from the rotary hearth furnace into a Zia All Purpose Vessel (ZAV) where it is smelted and refined into high quality steel. A specially designed turret with three independent arms, each supporting a separate ZAV, comprises the heart of the meltshop. No overhead cranes are required to transport molten metal from the smelting/refining operation to the ladle metallurgy station to the caster to an inspection station and back to the smelting/refining point. The molten steel is contained in the ZAV throughout the operations eliminating the possibility of steel con¬tamination by non-metallic inclusions occasioned by the exposure to ambient air during metal transfer into ladles. The result is the creation of very clean steel that can be alloyed to produce virtually any desired grade from stainless steel to common structural steel.

Jan 1, 1994

By G. M. Wenberg

Bacterial leaching of copper and uranium is practiced in environments containing available sulfur and iron and having a strong acidic reaction. However, many mineral deposits do not have these conditions; the chalcocite and native copper ores in Michigan's Upper Peninsula are examples. Bacterial and fungal populations were observed in samples taken from the White Pine Copper Company tailing pond and mine, and isolates were prepared of the dominant species. The isolates were then screened for solubilization of copper from tailing, ore, and concentrate during incuba¬tion in a carbon and nitrogen supplying medium. Certain Penicillium fungi solubilized significant amounts of copper under neutral to slightly acidic conditions. Leaching apparently was accomplished by release into the medium of metabolites which chelated with the copper.- The process was found to be highly dependent upon the medium and the concentration of copper in the source material. The paper describes sampling and screening techniques, presents the results of experimentation to standardize procedures and maximize the yield of copper, and discusses the nature of the leaching process. This preliminary research reveals a biological process which may find use in mineral extractions but whether it can be applied economically remains to be determined.

Jan 1, 1969

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930