Search Documents

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

Although small scale mining is regarded by many as of historical value only, this kind of mining activity is still much more widespread than is usually assumed. It has been estimated that it produces as much as ten per cent of the global mineral output. More significantly this figure is often much higher for many of the developing countries of Africa, Asia and South America, signifying the relatively greater contribution of small scale mining to the economies of those countries. It is also noted that small scale mining has always been a feature of mineral production in New Zealand and Australia. An attempt is made to define small scale mining, and the factors determining the suitability of small scale mining operations are discussed. The state of the art in small scale mining is reviewed and the author endeavours to rationalise the important parameters which contribute to successful small scale mining operations and discusses how these parameters may be optimised. The benefits of small scale mining to the mining industry as a whole and to the community at large are outlined. The paper concludes by emphasising the necessity to maintain small scale mining and 'explores' its future 'prospects'.

Jan 1, 1990

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By G. C. Smith

Process control applications in the minerals processing industry have grown extensively over the years due to the many benefits derived, both financially and operation-wise. Although control theory is widely known, conventional control does not address many of the problems posed by minerals processing circuits. Some of these problems include interactions between process units, large dead times, few and sometimes unreliable measurements of process variables, non-linear systems, disturbances entering the process, processes with varying dynamics, and many more. For the past 26 years Mintek has been active in the field of providing specific, customized solutions for the minerals processing industry. This paper focuses specifically on applications in milling and flotation control. The underlying control principles have been applied to a wide range of other processes including submerged arc furnaces. Advanced control application is implemented on a common advanced control platform, called the PlantStar. Much innovation has been brought to the fore in terms of adapting theoretical techniques and developing new methods to resolve specific milling and flotation circuit issues by using process control. The general approach adopted by Mintek when implementing advanced control is to enforce stabilization of the process as a solid foundation for optimization strategies to be built upon. In doing this, a robust control solution is presented, and the end result is flow and level stability, better product quality regulation, increase in throughput and a stable feed to downstream processes. The MillStar advanced milling control system ensures that the milling circuit is at all times easy to operate while achieving optimum product quality and throughput. Stabilization should include product size regulation and sump level control. Another important aspect of stabilization control is the handling of milling circuit constraints without introducing cyclical behaviour and with minimal disturbance to the final product quality. Process constraints may include factors such as process water limitations, cyclone feed density, and cyclone underflow angle. An optimization strategy should be developed to increase the mill throughput without affecting product quality or introducing mill overloads. The relationship between solids feed and power draw is examined and manipulated for optimization. The interactive nature of flotation circuits and the presence of recirculating streams tend to make satisfactory control almost impossible with conventional techniques such as PI (Proportional plus Integral) or PID (Proportional, Integral and Derivative) control. The FloatStar Level Stabilizer simultaneously considers all the flotation levels in a circuit by use of a multivariable algorithm, and takes compensating action in anticipation of disturbances. The FloatStar Flow Optimizer is an optimization strategy that controls the concentrate flow rate between various sections of a flotation circuit (e.g. Rougher ?Cleaner; Cleaner ?Recleaner). By controlling the concentrate flow between the sections, the mass pull, circulating loads and residence times of the circuit can be stabilized, thereby enhancing the performance of the flotation process. Optimizing grade and recovery are coupled with the dynamic optimization of circulating flows. The FloatStar Grade-Recovery Optimizer will maximize the grade in a section, whilst ensuring that recovery or any other process specific limits remain within predefined limits. With successful applications on several milling and flotation plants worldwide processing amongst others PGMs, gold, copper and nickel, Mintek has shown that it is a leader in milling and flotation control innovation

Jan 1, 2004

By Reeve JS

Heap leaching is a low capital cost alternative to conventional processing techniques for gold recovery from areas that contain small gold particles in a porous host rock.For successful heap leaching the ores to be leached must maintain good permeability after being stacked into heaps so that the leach solutions can percolate evenly through them.The presence of clays, slimes or excessive amounts of fines can hamper the flow of leach solutions causing channelling and producing dormant or unleached areas within the heaps. This results in unreasonably long leach periods and poor extractions. In extreme cases the clays or fines completely seal ore heaps, causing leach solutions to run off the sides of t'he heaps rather than penetrate the ore.The Northern Queensland Company uses the Agglomeration Heap Leach technique (AHL) to overcome the difficulties associated with clays or fines. This technique involves cementing the fines, by using readily available binders, into a rigid, porous network that greatly enhances uniform flow of cyanide leach solutions through the ore heaps.

Jan 1, 1986

By Sean E. Armstrong, Deepak Malhotra

The current trend in gold ore processing is the development of lower grade or highly refractory deposits. The perplexity of treating low grade oxidized ores has been adequately addressed by heap leach technology. However, refractory gold ores are very difficult to positively characterize the gold association within the mineral matrix. Gold accompanied with refractory sulfitlc or carbonaceous mineralization can often be sub­micron In size and occur interstitially. Mineralogical examination of these ores Is difficult, expensive, and occasionally Inconclusive. Hence, the metallurgist Is given little information for the selection of processing alternatives. The purpose of this paper Is to demonstrate the use of diagnostic leach procedures to assist the metallurgist' s decision-making process to solve some of these problems. By sequentially liberating and/or leaching gold associated with specific minerals, the amount of recoverable gold in each stage can be determined. Through careful interpretation of the results obtained by diagnostic leaching, the metallurgist can devise a flowsheet for treating the ore or solve a problem at an existing plant

Jan 1, 1992

The saying that a "prophet" is without honor in his own country does not always hold true, as is shown by the following from one of the local papers, which appeared under the above heading: "Edwin Ludlow, for more than seven-years vice-president of the Le-high Coal.& Navigation Co., with headquarters in Lansford, has resigned, to take effect July 1, when he will take up his residence in New York and engage as a consulting engineer. Mr. Ludlow, during the incumbency of his present position, has demonstrated his efficiency as an engineer and general manager in many directions, notable among which are the almost perfect methods in practice in the inside workings of the several operations under his charge and the erection of the most complete, most practical and most commodious breakers for the preparation of the mine product for market. In addition, his relations with organized labor have been cordial and his dealings with its representatives have been invariably based upon the principle of fair play."

Jan 7, 1919

By G. Riverin, C. Simard, W. D. Stevens

"An on-line technique to measure the efficiency of decoating I delacquering processes is being developed by Alcan' s Arvida R & D Centre. Decoating processes are used to remove moisture and coatings from shredded coated material such as Used Beverage Containers (UBC) before melting. Complete removal has been demonstrated to maximize metal recovery. Quantifying the weight of carbon and organic residue adhering to the shred surfaces is very difficult to measure directly, as the material can be highly folded. The technique developed indirectly measures the residue remaining by analysing the concentration of CO evolved in the decoater end zone exhaust gas.A commercial CEMS (Continuous Emission Monitoring System) incorporating an infrared type CO gas analyser was modified for on-line process exhaust gas analysis. Both pilot and plant trials had demonstrated that the CO concentration measured was inversely proportional to the efficiency of the organic removal achieved. As the quality of coated purchased scrap can be highly variable in moisture and organic content, continuous measurement should permit adjusting the feed rate and other decoater process parameters to the quality of decoating required."

Jan 1, 2000

By Th. Probst, M. Reuter, H. Orbon, U. Boin, J. Vonken, P. Vonk

Although secondary aluminum industry is well established in the world, the recycling process still requires further development to adequately control the process for a higher aluminum yield and a better product quality. In the present paper, recyclabilities of different aluminum scraps have been experimentally studied. Four types of commercial scraps were characterized and melted at 800 - 900 °C to recover 'aluminum metal with the protection salt flux of NaCl-KCl-Na3AlF6 under nitrogen atmosphere. According to the results, the difficulty of recycling aluminum scrap depends on the cleanness and the ratio of surface area to body volume. More non-metallic contaminates and higher ratio of surface area to body volume usually led to a lower metal yield. Usually cast ingots gave better results than rolling mill cuttings under similar conditions. Bottle caps can be recycled more easily than the margarine foil. The effect of temperature was not as significant as the composition of salt flux. The addition of cryolite was essential for a better metal recovery, especially for the scraps with higher surface area. Recycling

Jan 1, 2000

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

The Key Centre for Mines consists of the School of Mines of the University of New South Wales and the Departments of Geology and Civil and Mining Engineering of Wollongong University. The Key Centre for Mines/International promotes, markets and develops overseas activities in applied geology, mining engineering, mineral processing and extractive metallurgy specifically in response to the perceived needs in the region for mineral resource and other related earth-science based development. the Key Centre for Mines/International will be involved in the overseas marketing of formal courses; special training activities such as short courses and in-house programs; technical and educational consultancy; research and development projects, and in the establishment of regional links through twinning, exchange and various network arrangements with other organisations in the region. Activities which are now being developed include a training program for Korean mining engineers and geologists, teaching and curriculum development in the Mineral Resources Engineering Faculty of the University Sains Malaysia and a staff development proposal for the Department of Geotechnology of Khon Kaen University, Thailand

Jan 1, 1990

Colorado School of Mines Scientific Society held its first meeting on Friday evening, Jan. 14.1916. H. C. Parmalee gave an interesting talk on the Loss of Cyanide by Hydrolysis. F. E. BRIBER, Secretary. The School of Mines Society of the University of Minnesota held a meeting on Thursday evening, Jan. 13, 1916, at which Fred A. Jordan gave a talk on Magnetic Concentration of Iron Ores. Mr. Jordan is at present testing the new magnetic concentrator designed at the. School of Mines Experiment Station. This apparatus, if successful, will open up an enormous tonnage of ore on the Cuyuna and Mesabi ranges. ADOLPH DOVRE, President. At the College of Mines, University of Washington, Seattle, 33 mining men, with experience varying from one to 25 years, have enrolled in the 19th Annual Three Months' Short Session. At the annual smoker tendered the Short Session miners by the student branch of the American Institute of Mining Engineers, Capt. R. H. Stretch of the Alaska Bureau, Seattle Chamber of Commerce, delivered an address on The Mineral Belts of Alaska.

Jan 3, 1916

By O. Z. Klopsch, G. L. Craig

The fabrication characteristics and properties of phosphorized arsenical Lake copper have been compared with phosphorized prime Lake and phosphorized electrolytic seamless copper tubing, in a series of mill-scale tests employing commercial drawing schedules. Phosphorized arsenical coppers containing as much as 0.20 per cent arsenic were drawn with various reductions into 7/8and 3/8in. seamless tubing along with billets of the two types of arsenic-free copper. The effect of arsenic was determined by the average power required to draw given compositions and by the final properties of the respective materials in the annealed condition and after various degrees of cold reduction. Power consumption data show that no more power is required to draw arsenical coppers of this type than the arsenic-free copper. The result? of tensile tests indicate that arsenic increases the strength of cold-drawn tubing somewhat, but has no measurable effect on the properties of annealed tubing; the ductility of the tubing as evidenced by the elongation and other prescribed tests is unaffectetl by 0.20 per cent arsenic.

Jan 1, 1933

The Oregon School of Mines Society held its regular monthly meeting on the evening of October 23. This meeting was an informal reunion at which members gave accounts of personal experiences during the last three months. Many members of both junior and senior classes answered their country's call to arms and so did not return to college. The senior class is particularly well represented in the Army, as two men hold lieutenant's commissions and a third is already in France with a hospital unit. The junior class has also contributed men to various branches of the service. Plans for the regular meetings include discussions by members and lectures by outside authorities oil mining and allied topics. These meetings are open to the lower classes and all others interested. The Oregon School of Mines Society, composed of members of the junior and senior classes, has, joined with the sophomore and freshman relining students in purchasing a Liberty Bond under the name of the Miners' Club of 0. A. C. H. W. THOMS, President.

Jan 12, 1917