Search Documents

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

A cooperative service for engineers and their employers under the direction, of the American Institute of Mining and Metallurgical Engineers; American Society of Civil Engineers; American Society of Mechanical Engineers; and American Institute of Electrical Engineers, and with the cooperation in Chicago of the Western Society of Engineers, and in San Francisco of the California Section of the American Chemical Society and the Engineers Club of San Francisco. For information as to men available or positions open, address the nearest office. New York Walter V. Brown Manager, 31 West 39th St., Telephone Penn. 9220 Chicago A. Krauser, Manager, Room 1736, 53 West Jackson Boulevard, Telephone Harrison 1238 San Francisco Newton D. Cook, Manager, Room 715, 57 Post . St., Telephone Sutter 1684 UNITED ENGINEERING SOCIETY This is a corporation organized by the American Institute of Mining Engineers, American Society of Mechanical Engineers and the American Institute of Electrical Engineers to hold the title and administer the property at 29 West 39th St. In 1916 the American Society of Civil Engineers was admitted, and each society now holds an equal one-fourth interest in the ownership, occupancy, and administration of the building. The value of this property is estimated at two million dollars. A. I. M. E. representatives are : Arthur S. Dwight, J. Vipond Davies and J. V. N. Dorr. ALFRED D. FLINN, Secretary, 29 West 39th St., New York City. ENGINEERING FOUNDATION This is a fund established by the United Engineering Society in 1915 with a gift of $200,000 from Ambrose Swasey. Subsequent gifts had increased the fund to $600,000 on Jan. 1, 1927. The income, of the fund is used to further research in science and engineering and to advance the profession of engineering and the good of mankind. A. T. M. E. representatives are: H, M. Boylston, J. Vipond Davies, Galen H, Clevenger. ALFRED D. FLINN, Secretary, 29 West 39th St,, New York City.

Jan 1, 1928

By John M. Lovejoy

I take pleasure in transmitting herewith "Petroleum Development and Technology in 1927," in which we have attempted to set out in a series of 40 papers with attendant discussions the advances made in Production Engineering and Refinery Engineering during the year. The volume also contains a digest of round table discussions on Petroleum Engineering Research problems and Petroleum Engineering Education. In addition to the above we set out in 16 papers a review of production of each producing area of the United States and of the more important foreign countries, together with a review of the world's production and forecasts for 1928. We also include 8 papers on the Economics of the oil industry. The papers and discussions included herein represent the contributions of more than 200 engineers, including the foremost in each line. These papers were presented at technical sessions held in Fort Worth in October, 1927, and at the annual meeting in New York in February, 1928. We desire to express our thanks and appreciation to all those who have contributed to this volume. As in previous years, we have attempted to emphasize the value of both written and impromptu discussions. -We have made a practice of returning all impromptu discussions to the authors for correction and amplification, and because of this practice we feel that the discussions contained herein are in very presentable and readable form. It was decided by the nominat,ing committee when meeting for thc purpose of nominating officers for 1928 to eliminate the vice-chairrnanship for Transportation Engineering, as that branch of the industry seemed to come more naturally under the activities of the American Petroleum Institute. It was also decided by this committee to institute a new vice-chairmanship for Petroleum Engineering Research. Wc have had heretofore round table discussions on engineering research, but through the newly created vice-chairmanship, to which Mr. L. C. Uren was elected, we expect to have more comprehensive sessions on engineering research than heretofort.

Jan 1, 1928

By O. W. Rees, Gilbert H. Cady

Unit coal calorific values represent a close approach to pure coal values; they possess characteristics theoretically inherent in the latter values. They are essentially uniform in the same seam for areas possessing essentially uniform geological environment. They are higher in older than in younger coals in most cases, and in deeper than in shallower coals. In general, they display characteristics closely in accordance with expectation assuming that they are essentially indices of rank. Because it possesses these characteristics, the unit coal value is essentially a standard value, characteristic of each bed in each local region. Hence it can be used as a basis for determining the accuracy of results in newly established laboratories, or when new equipment is installed, or in checking the results of different laboratories, or even in determining the character of coal as mined or prepared if ash, moisture and sulfur values are known. DISCUSSION (A. C. Callen presiding) R. P. Hunson,§ Wayland, Ky. (written discussion).—One of the interesting observatioris made by the authors is that there is a more or less definite correlation between unit coal calorific values and the geological environment of the coal bed. It is very interesting to note that, in general, the unit B.t.u. value increases with the increase in the probable original depth of burial, and that each seam tends to increase in calorific value toward the areas of diastrophic instability. It is generally conceded that Parr's formula, for determining unit coal values, is about as accurate as any formula subsequently proposed for the same purpose. In his formula, Professor Parr did not differentiate between the sulfur present as iron pyrites and that present as organic sulfur. However, the practical application of the formula has shown that this is of little consequence. I agree with the authors that unit coal calorific values are useful ill determining the accuracy of calorimetric determinations, and in determining the character of the

Jan 1, 1934

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth's surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985

By H. De Cizancourt

The Pechelbronn (Alsace) field is the only important French producing field. During 1934, development was carried on as in previous years. The total output of this field reached 553,575 bbl. in 1934, showing a slight decrease from the 1933 figures. Of the total, 315,000 bbl. (56 per cent) was extracted by drilling, while 238,875 bbl. (46 per cent) was obtained by means of shafts and galleries. Exploration of deep Jurassic and Triassic horizons was still in progress at the end of 1934. A deep well reached the Upper Triassic at a depth of 34 m. (2736 ft.). (Information kindly supplied by M. S. Mena, Directeur Technique.) As mentioned before, the small Gabian field (Herault) is gradually being exhausted. No drilling operations were undertaken in 1934, the small production being restricted to the pumping of old wells. Two exploration wells, noted as "drilling" at the end of 1933, were completed in 1934; viz., Lavelanet (Ariége) at 3785 ft. and Santenay (Niévre) at 2578 feet. French Possessions Algeria.—No drilling at Tliouanet. Out of a total of 100 wells drilled in the area, only 8 are still producing. No exploration work is reported during 1934 in Algeria. Tunisia.—Two wells completed; one well drilling at the end of 1934. A total of 11 wells is reported to have been drilled before the beginning of 1935; out of these, 8 were completed before the present program was begun. Morocco.—Exploration work progressed actively last year. The outstanding event was the coming in of Ts. 26 well at 1243 ft. This well took fire, therefore great difficulties were encountered in the accurate measurement of initial production; the figure of 1500 bbl. of oil given here is a near estimate. Oil flowed accompanied by a great amount of water. The apparent decrease of drilling operations in 1934 is explained by the increase in field activities after the results of Ts. 26 were known;

Jan 1, 1935

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By M. H. Moys, H. Dong

"Discrete Element Method (DEM) has become a standard tool to simulate grinding mills in order to gain information about load behaviour, power drawn, etc. However, parameters necessary to run a simulation are not always readily available. For example, the coefficient of restitution used in DEM simulation from the literature ranges from 0.1 to 0.9 due to lack of accurate values. The lack of correct input parameters results in the fact that some simulation parameters are adjusted to match the simulation prediction with the experimental results. It is inappropriate to tune one single parameter arbitrarily in order to fit the prediction with experimental results. The correct value of parameters for DEM simulation should be established, and rigorous validation on simulation results by DEM needs to be done.The objectives of the ongoing project are to measure the coefficient of restitution at conditions analogous to grinding practice. Equipment has been built to measure the coefficient of restitution. A typical case of impact test showing the vertical position of a ball as a function of time is presented in Figure 1. The coefficient of restitution between steel ball of different sizes and the targets including steel liner (e = 0.91), mild steel block (e = 0.57) and rubber liner (e = 0.7) have been measured. The coefficient of restitution reduces to 0.38-0.52 when there is a layer of coal particles (1-2 mm) on the steel liner. The effects of ball size, drop height on coefficient of restitution are investigated. Then a DEM code is developed of several contact models to simulate the impact process. This code can reveal details on velocities (translational and rotational) and forces (normal and tangential) during the brief impact interval. Figure 2 is a comparison of the rebound rotational velocity between experiment and prediction by different models. The results can be used as DEM input and to assess contact models."

Jan 1, 2003

By J. L. Weeks, K. F. Smith

IN order to determine the magnitude of thermal conductivity changes resulting from alloying vanadium with titanium and a few other elements, several sam~les were PrePared and measured. The thermal conductivity -values reported herein in Table I were determined with an apparatus previously described.' As in recently reported2 determinations on uranium and uranium alloys, whose thermal conductivities are in the same range as vanadium," the accuracy of the values was checked by using synthetic sapphire." The error in the measurement is estimated to be '-3 pct or 0.003 cal sec-1 cm-l "C-1, whichever is larger. The vanadium used in preparing the samples was the calcium-reduced type and was supplied by the Electro Metallurgical Co. as 99.6+ pct pure. All alloying elements used in the preparations were 99+ pct pure. A nonconsumable tungsten electrode arc furnace was used for melting the alloys and, without opening the furnace, each ingot was re-melted a number of times to insure homogeneity. The samples as prepared by the Armour Research Foundation were machined from as forged material without annealing. Acknowledgment The note is based on work performed under the auspices of the AEC. References 'J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. 2 J. L. Weeks: Thermal Conductivity of Uranium and Several Uranium Alloys. Trans. AIME (1955) 203, p. 192; Journal of Metals (January 1955). 3C. A. Hampel: Rare Metals Handbook. (1954) p. 593. New York. Reinhold Publishing Corp. Thermal conductivity of vanadium is given as 0.074 cal sec-1 cm- '°C-1 at 100°C. 4 J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal Amer. Ceramic Soc. (1952) 35, p. 15. At 70°C, K = 0.071 cal sec-l cm-l °C-1.

Jan 1, 1956

The following additional studies are recommended: 1. Future development of the magnetic sludge process should involve optimization of the process variables; these include stirring rate, sludge heating time, aeration rate, method of preliminary sludge dewatering, and the effects of magnetic separation for final sludge processing. In addition, the matter of amenability of coal mine waters to treatment should be considered more thoroughly by means of a more comprehensive literature review as well as actual tests on mine drainage samples. 2. The technique of sludge freezing should be explored further. Emphasis should be given to conservation of energy in the process, and the filtration characteristics of the resulting sludges should be evaluated. 3. Further studies should be conducted on the feasibility of the CO2-addition approach to mine drainage sludge densification. The filtration characteristics of product sludges should be evaluated, and the possibility of recovering and recycling the residual alkalinity of the sludge, either directly as CaCO3 or as CaO plus CO2 after calcination, should also be explored further. 4. Efforts should be made to develop cost data for the conceptual processes involving magnetic sludge formation, sludge freezing, and C02 pretreatment, with the purpose of selecting at least one of these processes for further testing at a field site. 5. The use of inexpensive waste materials (e.g. fly ash, "red dog," slag) as sludge additives, possibly in conjunction with coagulant aids, should be considered further. Results of the present studies have indicated that such materials, employed in relatively large amounts, increase the density and enhance the filterability of sludges from lime neutralization of coal mine drainage. The use of pulverized blast furnace slag in this regard appears particularly promising, and studies should be made to ascertain its availability, relative cost, residual alkalinity, and behavior as an additive in conventional mine drainage treatment processes involving lime neutralization and aeration.

Jan 1, 1971

By Paul Worsey, Braden Lusk

Differences exist between public perception of construction blasting and quarry blasting. In general, people are able to tolerate short term inconveniences much better than long term ones. The paper focuses on the public perception of quarry blasting in St. Charles County, MO. This expanding urban environment has seen new legislation targeting preexisting quarry operations that have been in place for many years. A survey was made comprising interviews conducted to gauge perceptions of persons with varying demographics. Interviews covered topics involved with quarry blasting and its reporting methods. The purpose of the interviews was to determine public perception of blasting and how best to report results of vibration measurements. The use of different, less technically complicated measurement scales for vibration and airblast was considered as an alternative reporting system. The question for the industry is, “Has our past haste in adopting complex scientific scales and units been detrimental to us?” In other words, are we reporting the correct things? For airblast, the decibel scale was evaluated against millibar in the public eye. Peak Particle Velocity was also compared to that for displacement. Current legislation in the county is based on complaint levels rather than damage criteria. The complaints most likely not only come from ignorance to the affects of blasting on structures, but also sparse understanding of the units used to report these affects. The past practice of treading softly as an industry has been proven to be a poor choice, and education of the public as well as lawmakers on all levels is necessary. The Mississippi Valley Chapter of ISEE has begun to conduct seminars to this end. One educational seminar has taken place for officials and lawmakers in the St. Louis area, and others are in the planning stages. The focus of this paper is to gauge perception of the damage criteria reported today, and locate focal points for future education of the public in rapidly expanding suburban environments.

Jan 1, 2005

By John Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulfide concentrate that must be treated by roasting, biooxidation or pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process that also meets Ontario's stringent environmental regulations. A comparison of biooxidation and pressure oxidation was completed early in 1990. Placer Dome selected pressure oxidation as the preferred process to replace the roaster. The commercial plant design was based on technology supplied by Sherritt Gordon. In July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The Campbell Red Lake Mine, in Balmertown in northwestern Ontario, is the first plant in Canada to use Sherritt Gordon's pressure oxidation technology to recover gold from a refractory ore body. A similar process has been used at Sao Bento in Brazil since 1986. The Porgera complex in Papua New Guinea also uses Sherritt's technology. At the Campbell Mine, gold occurs as either free gold or is encapsulated with sulfide minerals, mainly arsenopyrite, pyrite and pyrrhotite. These sulfide species are recovered from the ore by crushing and grinding to 80% -75. µm (200 mesh), followed by flotation. About 40% of the gold in the ore is recovered by gravity separation. The remainder reports to the ground slurry feed to flotation. The flotation concentrate averages about 55 to 60 t/d (60 to 66 stpd). A typical analysis is shown in Table 1. Before the installation of the pressure oxidation plant, the flotation concentrate was treated in a two-stage, fluid bed roasting circuit. Roaster off-gases passed through two parallel sets of cyclones, followed by electrostatic precipitators. Arsenic trioxide was captured in a four-chamber baghouse before the gas was discharged to a stack. The arsenic trioxide was sold or conveyed to an underground storage vault. The roasted calcine was fed to a gravity separation circuit and then subjected to cyanide leaching. Gold was recovered from the filtered leach solution in a Merrill-Crowe zinc precipitation circuit.

Jan 1, 1992

Shoveling ore cost so much at Tyrone during the year 1917 that it was deemed advisable to conduct tests to see where the fault lay. These tests were in the nature of time studies and extended over a period of very nearly a year. No data were available on this work to supply a starting point, so it was necessary to begin in a very elementary way, to find out the capacity of the average Mexican laborer. To' obtain a basis for comparison, it was necessary to determine the capacity of various types and sizes of shovels, so as to know whether the 21-1b. (9.5-kg.) load was the best load underground as well as on surface. A list of essential factors influencing shoveling was also made out during the course of a short series of preliminary time studies, and the motions involved in shoveling were analyzed and subdivided for convenience in studying. The necessary forms and record sheets were also decided upon at this time. A second short series of tests was then conducted on the surface, so as to be able to estimate the negative effects of underground work on the shovelers, and to minimize, as far as possible, the need for studying obviously poor types and sizes of shovels under the difficult conditions to be encountered in the mine. The test work underground consumed by far the greater proportion of the time and was divided into three series: Shoveling directly into a chute; shoveling into a wheelbarrow and tramming to a chute; and shoveling into a car and tramming to a chute. In each series the following points were determined for various lengths of time worked: Number of shovelfuls handled per minute, effect of distance thrown on shoveling speed, amount of rest required, amount of time consumed in tramming and dumping, proportion of working day occupied in shoveling, total tonnage handled during various working periods, effect of distance on tonnage handled during the day.

Jan 2, 1919

By Walter O. Snelling

In combating mine-fires the use of carbon dioxide as a means of producing an atmosphere in which combustion cannot be sustained, has been many times suggested and frequently tried, generally with a fair degree of success. The carbon dioxide is produced by acting on limestone with dilute sulphuric acid, large wooden boxes being used to hold the limestone, and arranged in such a manner that one box may be cleaned and refilled with blocks of limestone while another is being used in generating the carbon dioxide.. The gas is led by means of pipes of large diameter to the location of the fire, tight brattices having been previously put up as close to the fire as possible on every side, so as to limit the space to be filled with the gas to the smallest possible volume. The cost of producing carbon dioxide has been, however, a decided draw-hack to the use of this method, and the danger of producing carbon monoxide by the reduction of the carbon dioxide by heated carbon, and consequently bringing about an explosion, has also tended to prevent the application of this method. The use of sulphur dioxide in combating mine-fires has not, I believe, been previously suggested or tried, and yet the method presents such decided advantages over the use of carbon dioxide that it seems proper to suggest the advisability of considering it as a cheap, convenient, and safe means of fightr ing stubborn mine-fires. 1. Cost, Preparation, etc.—One ton of brimstone, costing from $20 to $30, will produce about 25,000 cu. ft. of sulphur dioxide gas, and allowing for all sources of loss it is probable that sulphur dioxide gas can be produced for about $1,300 per 1,000,000 cu. ft. For carbon dioxide gas, produced by the action of sulphuric acid on limestone, a good estimate would be $4,000 per 1,000,000 cu. ft., provided that sulphuric acid

Jan 1, 1909

By W. H. Burke

Deeper drilling, resulting in greater circulating distance and pressure, has directed attention to the advantages of the study of properties and control of rotary muds, which until recently have not had much consideration. One fundamental property of muds is viscosity, and viscosity is influenced by the quantity and character of colloidal material and can be controlled by chemical treatment. Colloidal Matter of Rotary Muds Two types of colloids are found in muds; the hydrophobic and the hydrophilic. Hydrophobic colloids do not associate intimately with water and are sensitive to small quantities of electrolytes. Hydrophilic colloids associate intimately with water, but are not so sensitive to electrolytes. The colloidal particles of rotary muds are derived from clay; In clay the particles may range in size from submicroscopic to macroscopic; a substance is a clay if the greater proportion of the particles are within the size limits prescribed for clay. The larger particles are inert and have no effect on the viscosity of normal hydrophobic colloidal muds. There are two theories accounting for the colloidal properties of clay-water suspensions: (1) the physical theory, that clay in water is a coarse colloidal suspension, and (2) Ashley's1 theory, that clay is a granular material with a colloidal gel surrounding the crystalline grains. The most important colloidal substances known to exist in clays besides the clay particles are: (1) colloidal silica, (2) colloidal alumina, (3) colloidal ferric hydroxide, (4) colloidal silicates, and (5) colloidal organic matter. Plasticity, a peculiar property of clay-water suspensions, is due to the colloidal particles. It is commonly (although not with strict accuracy) measured in terms of viscosity, and depends upon the amount and the state of flocculation of the colloidal matter present in the suspension. Fluidity in a rotary mud may be caused by a lack of colloidal clay particles or by deflocculated or flocculated clay particles, while viscosity in a

Jan 1, 1935

By Ajay Mahajan, Manoj Mohanty, Vishal Gupta

Modern coal processing plants utilize multiple cleaning circuits to efficiently beneficiate different size coal fractions of run-of-mine coal. An older plant optimization approach is to maintain average product quality from individual cleaning circuits at the same level as the given product specifications for the overall plant. However, many past studies indicate that the equalization of product quality approach fails to produce the maximum plant-yield. A newer approach, known as equalization of incremental product quality, requires that the incremental product quality obtained from each circuit be maintained at the same level to satisfy the overall plant product quality. This approach ensures the maximization of plant yield while satisfying a single product quality constraint. However, while dealing with multiple product quality constraints, this approach by itself may not be sufficient to obtain the desired maximum yield. For the simple reason that the dirtiest particle (or group of particles) with respect to one quality constraint may not be the same particle (or group of particles) with respect to another quality constraint, the mass yield versus product quality relationship generated by equalizing different incremental product quality may not be exactly the same. Therefore, an additional search technique has to be utilized to determine the global-maximum value of plant yield. Thus, the main objective of this study was to utilize an emerging optimization technique, known as genetic algorithms (GA) to maximize plant yield while satisfying multiple product quality constraints. The maximum plant yield obtained from this approach was nearly same as the maximum yield obtained by the incremental product quality approach while satisfying one specific product quality constraint. The GA was applied on a coal preparation plant that utilizes four circuit operations - heavy medium bath, heavy medium cyclone, spiral and froth flotation. The results showed that using GA as an optimization process gives 2.56% higher yield that will result in additional revenue generation of $5,120,000 per annum than average product quality approach.

Jan 1, 2005

R. F. WOOD,* Sandusky, Ohio.-I made a few tests of gun-metal specimens, after I noticed the results on quenching -reported by the Bureau of Standards. The data of one such test are given herewith. The bars were heat treated and quenched before they were machined, and in all cases they were brought up to 700° or 800°. They became extremely brittle,, showed almost no elongation, except such as was caused by the failure of the pieces to fit together after they were pulled, and the tensile stength was reduced from around 35,000 to about 13,000 lb. per sq. in. In addition, the weakening effect of the quenching seemed to be almost as marked when the bar was allowed to slowly air-cool from red to black, and then quenched, as it was by quenching directly from the red heat. Test Bars.-Rough size, 9/16 in. diam. over test section, grips 13/16 in. diam. Cast two in a flask, one on each side of a block 8 by 4 by 1 in. and fin-gated thereto from the grips but not from the test section. Poured with flask in inclined position, with gate to lower end of block and riser from upper end of each test bar. Bars were machined to ½ in. over the test section, after heat treatment. Casting the Bars.-Charge of 1500 lb. consisting of 400 lb. of new metals and 1100 lb. of G turnings and scrap was melted in open-flame oil furnaces and then poured into a 1-ton ladle. From the ladle 150 lb. was poured into a preheated No. 50 crucible, land from this the flasks of test bars were poured. The six flasks are indicated below by the numbers 1 to 6 and the bars in each flask by the letters a and b, thus 4a and 4h, for instance, were the two bars in flask No. 4.

Jan 12, 1919

By Robert Lepsoe

It is generally realized that in cyaniding the precipitation efficiency of zinc dust is due to the fine division or extended surface of its metallic particles; but frequently it is thought that the presence of other metals, say 2 to 3 percent. lead, is advantageous, causing more complete precipitation. The results of testing about fifty brands of commercial zinc dust have led to the conclusion that there is a distinct relation of precipitation efficiency to fineness and that the effect generally can be estimated by examining the size of metallic particles. The presence of lead was not found to be of any importance. Specifications Generally the term "97 per cent. to pass a 350-mesh screen, 95 to 97 per cent. uncombined metallic zinc" is used by the leading European exporters. Among the many methods of determination of metallic zinc, I have found the iodine test (iodine in potassium iodide) very satisfactory and rapid. It has been controlled by the other methods, samples of the same product having been sent to three different analysts: Iodine method................... 98.11 per cent. metallic zinc, Volumetric method.............. 07.63 per cent. metallic zinc, Ledoux Co., New York Bichromate method.............. 08.16 per cent. metallic zinc, Watson Gray, Liverpool. England Bichromate method.............. 98.20 per cent. metallic zinc, Norway Inst. of Tech., Trondhjem Determination of Precipitation Efficiency The method devised by W. J. Sharwoodl was used. The method proved to be satisfactory, the tests being merely for the comparison of different samples, hence the personal factor in manipulation was eliminated. As nearly all tests showed more zinc in solution than was accounted for by the silver precipitated, the term "dissolved zinc" was introduced—it means zinc dissolved by the action of cyanide and oxygen: Zn + 4KCN + H2O + O = K2Zn(CN)4 + 2KOH; or more probably, resolution of its equivalent precipitated silver, as tests stirred two hours showed more "dissolved zinc" than those stirred

Jan 1, 1925

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953