Search Documents

By J. F. Barkley

 This paper describes the method used and results obtained in testing a hand-fired down-draft furnace at a plant in Washington, D. C., in order to determine the method of firing that would give the best results with a minimu of smoke. The smoke regulations of the District of Columbia are very rigid, and are well enforced, A paragraph of the ordinance relating to furnaces other than household, reads, "The emission of dense or thick black or gray smoke or cinders from any smokestack or chimney 113ed in connection with any stationary engine, steam boiler, or furnace of any description within the District of Columbia shall be deemed, and is hereby declared, to be a public nuisance". This ordinance, if literally enforced, would eliminate all ordinary hand-fired grates and furnace combinations where coal other then anthracite is used. However, in several Gov- ernment plants where hand-firing of coal is still necessary conditions have been satisfactorily met by installing the down-draft type of furnace. In these plants, as at all hand-fired plants, considerable difference in operating details and methods is found. The firemen are paid day laborer's wages and are often inexperienced. The instructions of the furnace makers fre- quently do not appeal to the firemen, and are not closely followed, This is partly due to the necessity of running the boilers continuously at much higher ratings than were intended by the manufacturer. Tests were made on a Hawley furnace of this type to improve the methods of firing, particularly at the higher ratings.

May 1, 1924

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By William P. Barnett

In 1988, the US Department of Energy's (DOE) Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation and advanced cycloning. Each relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. The National Energy Strategy (NES) and the Clean Air Act Amendments (CAA) of 1990 are examples of the nation's commitment to a clean environment. The need to use the nation's energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SO2 emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur removal beyond currently achievable levels. Opportunities are provided in the form of incentives associated with a novel system of SO, allowances and a policy environment based on the proper functioning of familiar market forces. An allowance, as defined in Section 402(3) of the Amendments, is "an authorization ... to emit ... one ton of sulfur dioxide." To achieve the objective of the Clean Air Act Amendments, SO, emissions will be eventually capped at 8.12 Mt (8.95 million st) annually by controlling the number of allowances issued nationally. By permitting allowances to be bought and sold once issued, the law encourages "overcompliance" as a source of profit for owners of excess allowances. Many details concerning the administration of allowance trading are not yet written.

Jan 1, 1992

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time. '

Jan 5, 1916

University education in Australia is changing, driven by greater market orientation, reduced funding available per student, especially in the higher-cost minerals industry disciplines, and the call for more flexible delivery of subjects and courses to meet changing lifestyles and expectations. The opportunity exists for a true partnership to develop between industry, government and academia that will reshape minerals education in Australia and secure the future supply of the specialists industry needs to maintain international competitiveness. If this partnership does not emerge, it is anticipated that AustraliaÆs somewhat fragmented and unstable higher education system, especially in the disciplines of particular relevance to the minerals industry, will be put under further pressure so decreasing its effectiveness to produce quality graduates. The Minerals Council of Australia in 1998 published æBack from the BrinkÆ, a discussion paper which proposed strategies to build a world class minerals tertiary education system in Australia. Those strategies are now being implemented collaboratively with principal emphasis on the disciplines of mining engineering, metallurgy and earth science and as far as process is concerned, on the necessity to æcooperate to competeÆ. For metallurgy, the challenge is to integrate more closely undergraduate teaching with the existing world-class research centres and to link the tertiary institutions in such a manner that the strengths of all components are harnessed and then made available nationally in major population centres and at remote sites where appropriate. For industry the challenge is to build effective partnerships with the academic community that will enable and assist the agreed course of action to take place.

Jan 1, 2000

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time.

Jan 5, 1916

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By George M. Filz

Restrained basement walls and unrestrained but massive concrete walls on rock foundations experience very small movements in response to lateral earth pressures. Such walls are often designed using at-rest earth pressures without consideration of either compaction-induced lateral pressures or vertical shear forces resulting from compression of the backfill in response to self-weight. Compaction-induced lateral earth pressures can be detrimental to the integrity and stability of retaining walls. For example, the lock walls at Eisenhower and Snell Locks on the Saint Lawrence Seaway near Massena, New York, were damaged by compaction-induced lateral earth pressures, and an extensive rehabilitation program was necessary to ensure safety of the locks. Vertical shear forces, on the other hand, can be beneficial to stability because the downwards-directed vertical force tends to counteract the overturning moment from lateral earth pressures. The contribution of vertical shear forces is not included in most modern analyses of non-moving walls, but Terzaghi used this effect in his design of a high concrete retaining wall at Fifteen Mile Falls Dam. The lock walls at Eibach Lock on the Main-Donau Canal in Germany were instrumented for both lateral and vertical stresses applied by the backfill to the wall, and the resulting measurements show that vertical shear forces from the backfill were significant and persistent over the multi-year period that the wall was monitored. Other data from pilot-scale retaining walls confirm the existence of both compaction-induced lateral earth pressures and vertical shear forces. These forces should be considered in design of non-moving walls.

Jan 1, 2003

By M. Rîsteiu

The authors aim to analyze the behavior of smart sensors using Transmission Control Protocol/Internet Protocol (TCP/IP) infrastructure in hazardous applications, because of their advantages regarding safety, expansion and Quality of Service (QoS). Initially, some constraints are discussed for these applications. Then, the possibility is analyzed of using 2.4 GHz TCP/IP based transmission for sending data out of an industrial area. In this setup the authors evaluated the round-trip implementation (which requires a database of packet lengths), related to the delay introduced by the radio transmission algorithms from 802.15.4, and 802.11d/g protocols. Tuning results of different varying time-delays were compared to the constant delay cases from the literature (Deák, 2003; Lincoln, 2003). Both the hardware and software setups are implemented. Based on TinyOS specific software for hardware checking/ initiating communication/ starting/ closing measurements the authors have developed separate/combined procedures for testing the integrated devices. Measured time delay is presented and analyzed, for both beaconed and non-beaconed 802.15.4 transmission, with power optimization criteria. By testing two different implementations (Zhang et al., 2001), (ATmega256 RZAV - 256KB flash memory, the CC2420 IEEE 802.15.4 and ZigBee-compliant RF transceiver core - 128KB flash memory) the authors have found some time delay variations as a result of local processing by the ZigBee controller with an amount of flash memory. The work is also focused on adapting industrial measuring standard systems to the smart sensors, but not only through the 4-20 mA standard.

Jan 1, 2008

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

By J. D. Meakin

The self-diffusion coefficients of ß tin have been deterttlltled using a plating and sectioning technique. The principal diffusivities pavallel and perpendicu1ar to the "c" axis are given by the Arrhenius relations Dc = 8.2 exp (-25,600/RT) sq cnl per sec and Da = 1.4 exp (-23,300/RT) sq cm) per sec. The results are discussed in terms of a vacancy mecharism of diffusion. In conjunction with an investigation of diffusion in dilute indium-tin alloys we have reexamined self-diffusion in tin single crystals. The published self-diffusion coefficients of tin, eensham') have always appeared anomalous in comparison to diffusion data for other metals and do not correlate with parameters derived from creep tests.' In addition to the necessity of confirming the self-diffusion values for use in analyzing the alloy work, self-diffusion in an anisotropic lattice is of considerable fundamental interest and confirmation of the published data seemed worthwhile. For a crystal with an axis of symmetry three-fold or higher the diffusivity at an angle 6 to the axis is given by D? = (Da - Do) sin2?+ Do [1] where Da and Do are the principal diffusivities perpendicular and parallel to the axis. For a particular diffusion mechanism, again in a crystal of axial symmetry, these principal diffusivities are [2] Do - ? ?i2 COS?i In these expressions ?i is the displacement undergone by the ith atom and 8, is the angle this displacement makes with the symmetry axis. In this, as

Jan 1, 1961

By L. B. Lindemuth

TO those who are in a position to carry the thought to a conclusion, I would like to present a theory of the cause of blisters in ' galvanized sheets. Blisters that are caused from piping and shrinkage cavities will not be considered, because the reason for their formation is entirely obvious. Blisters that periodically occur, with no apparent system of location, number, size or grouping, and then disappear with no apparent change in manufacturing method, are the ones to which this theory would apply. Examination of blisters of the latter type has shown that they contain hydrogen gas at atmospheric pres-sure, and that occasionally traces of oxide or sulfide are found on the inner surface of the blisters. These two characteristics have led to the rather general idea that hydrogen gas generated in pickling, and that iron oxide supposed to be inherent in the ingot and causing weak spots, were, in some manner, responsible for the development of blisters in galvanizing. The theory which I wish to advance is that these blisters are caused by moisture that has penetrated the steel after the annealing operation. This moisture comes from the atmosphere, or from pickling or wash-ing, and when it is suddenly expanded into superheated steam in galvanizing, the increase in volume is so great that it cannot escape with sufficient rapidity through the small opening which it entered as moisture. The pressure so generated forces the sheet apart along those lines of lamination that may be found in practically all flat sections of steel rolled comparatively cold.

Jan 5, 1927

By Bashir Ahmed, Fred D. Wright

Numerous investigators have studied the various factors that influence the ultimate strength of model mine pillars, such as ratio of height-to-least width; restraint or friction on the top and bottom; 1,2 the effect of stress distribution in pillars on their strength;3 and the scaling factors involved in applying the results of model pillars to full-scale pillars. However, the load-bearing capacity of pillars after initial failure does not appear to have been investigated. Yet many mines employ methods in which small pillars or pillar remnants are left systematically; these pillars crush as mining progresses and, of necessity, affect the behavior of surrounding rock even after initial failure. The effect of such crushed or crushing pillars depends largely on their load-deformation characteristics. This chapter presents the results of a preliminary investigation to determine the load-deformation characteristics of a few model mine pillars to and beyond initial failure. Various investigators have also studied the elastic and viscoelastic behavior of mine structures. In such studies, computers are frequently employed to obtain numerical results by the finite difference or finite element methods. It would be entirely feasible to write a program that would approximate the load-deformation characteristics of pillars to and beyond the crushing stage if these characteristics were known. More accurate information on the induced stresses and deformations in overlying strata and on surface subsidence could be obtained, information which should result in better strata control by enabling the engineer to calculate more accurately the effects of changes in pillar spacing, size, and shape.

Jan 1, 1972

By Leonard Waldo

The recent and rapid development of the physics of engineering materials at temperatures as low as that of liquid air and as high as that of the electric are, has drawn renewed attention to the absence of tables, properly printed and spaced, for the convenient and accurate translation of temperature from centigrade to Fahrenheit scales and vice versa. It is to be noted that the Fahrenheit scale is the almost universal usage in foundries and shops in the United States, though the laboratories of the same works employ the centigrade notation. The growing use of the electric furnace in Germany and France calls for much American citation all in centigrade high temperatures, and while the arithmetical calculation is simple, it becomes burdensome when often repeated. I have been surprised at the numerous reprints of Table I. from centigrade to Fahrenheit degrees, first privately printed for personal use, which have been made by works, blue-prints, text-books, and technical journals, and I hope that Table II., from Fahrenheit to centigrade degrees, will be equally useful. For mental calculation the easiest rule to convert centigrade into Fahrenheit is to add 32° to twice the centigrade reading less one-tenth of this product: Thus 1000' C. = 2000" — 200" + 32" = 1832" F., and to convert Fahrenheit to centigrade, subtract 32" from the Fahrenheit reading, multiply by 10 and divide by 2 and 9 successively : Thus 1000° F. = 1000° — 32° = 968° X 10 = 9680° - 2 = 4840° - 9 = 537.77° C. Another and often very convenient method is by 'use of a graphic construction as follows :

Jan 1, 1913

By Charles L. Kimbell

The year 1988 for the minerals indus¬try was one of favorable worldwide economic conditions for continued, rationally constrained growth. There was continued improvement in relations between market economy nations and the Soviet Union and China. The "shooting war" between Iran and Iraq ended. Soviet troops withdrew from Afghanistan. And conditions were generally favorable for economic growth in developed market economy countries. These favorable conditions were darkened only somewhat by the continuing foreign debt crises discernible in some major mineral producing developing market economy countries. However, there were situations developing that became major headlines in the late spring - situations that may have pronounced effects in 1989. The most significant event is the muddled situation in China. There is a good chance of worsening international relations and consequent restraint of development projects that could prove beneficial to China and her international partners. Of only slightly lesser evident significance was the death of Ruhollah Khomeini in Iran. This could lead to a variety of paths for the new Iranian leaders. Continued outbreaks of ethnic unrest in the Soviet Union clearly presented problems to the Gorbachev regime. This unrest has raised questions of how far the doctrines of "glasnost" and "peristroika" would be extended, including extensions into the minerals field. Another area of unrest is Panama with its tainted election and the Western Hemisphere's obvious dissatisfaction with the Noreiga regime. While not a direct threat to any major mineral industry enterprise, the political situation certainly presents a potential threat to the Panama Canal. That threat would have considerable impact on world

Jan 1, 1989

By H. A. D. Kirsten

The structural competence of mesh- and fibre-reinforced shotcrete was investigated in two series of tests on full-scale panels. It was found that uniformly distributed loading was marginally less demanding than point loading, mesh reinforcement was superior to fibre reinforcement, Dramix fibre and Melt Extract fibre were similar in reinforcing characteristics, and 30 mm to 35 mm was an optimum fibre length. Furthermore, the consistency of the fibre content could not be assured on practical mining sites, and an average fibre content of about 1,5 per cent was the maximum that could be obtained for fibre lengths not exceeding 35 mm. Also, owing to its greater flexibility, shotcrete reinforced with diamond mesh was preferable to fibre-reinforced shotcrete in mining excavations subject to squeezing conditions. In view of the difficulties associated with assuring the consistency of the fibre content in mining applications, it appears that the sophisticated attributes of fibre-reinforced shotcrete can be effectively exploited only in civil-engineering applications in which quality assurance is subject to explicit contractual control. Load-deflection curves, together with measurements of compressive stresses in the surfaces of some of the panels, enabled the ultimate flexural strength of reinforced shotcrete to be rigorously formulated, and rigorous design procedures for shotcrete subject to bending and direct thrust to be developed. The application of the procedures is demonstrated in a practical design case in which the moments and thrusts in a tunnel lining are determined in a numerical analysis of the interaction between the lining, the surrounding rock, and the rock-reinforcing system.

Jan 1, 1992

By Lee Trudick

The secondary dispersion of copper, zinc and fluorine in A horizon soils was examined in Pope and Hardin Counties, IL, by sampling 122 sites along five traverses. Four of the traverses were taken above a deeply buried manto; a fifth intersected a vein complex exposed at the bedrock surface. Plants at each site were examined and analyzed for fluorine and on one traverse for copper and zinc. The A horizon soils were also tested for lead, manganese, barium, nickel and cobalt. The total content of copper, zinc, and other heavy metals in soils was determined by atomic absorption spectrometry (AAS) after acid bomb dissolution. Fluorine in soils was determined by fluoride ion-specific electrode after fusion with NaOH. Several cold- leach methods were also used. The analysis of A horizon soils for copper and zinc by AAS after acid bomb dissolution is a promising geochemical tool in the search for fluorspar. The acid bomb dissolution method is simple and takes little laboratoy time; it Produces a total dissolution of the sample with relatively little loss of the elements, and 20 elements can be analyzed from the same sample. In this study, the highest copper values were 80 times the local background level of 25 ppm and anomalies of this element tended to outline the fluorspar orebody better than either zinc or fluorine. The greatest zinc value was 15 times the local background level of 100 ppm, while the highest fluorine values were approximately four times the local background level of 165ppm.

Jan 1, 1982

By Y. Jeannin, C. Mannerskantz, F. D. Richardson

Measurements have been made between 1040o and 1300°C of the equilibrium between chromium metal, chromic oxide, hydrogen, and water. The results are in closer agreement with those deduced from recent thermal data than with previous equilibrium values. They lead to the equation ?G°1300°-1600°k = -266,700 + 59.95T ± 300 cal for the formzation of a mole of Cr2O3 from chromium and oxygen. This same equilibrium has been studied with the chromium dissolved in solid iron, and in this way chromium activities in Fe + Cr alloys have been established. The measuremenis show that there are substantial positive deviations from ideality in the a, and b phases, and support the results obtained by Heymer and Kubaschewski against those of other investigators. There is considerable disagreement between existing data,1"4 which is referred to in the Discussion, concerning the equilibrium Cr2O3 + 3H2 = 2Cr + 3H2O [l] There is also substantial disagreement between the results obtained by various investigators5-' who have measured the activities of chromium in its alloys with iron by the Knudsen effusion vapor pressure method. In view of the importance in metallurgical processes of chromium and its oxide and of Fe-Cr alloys, an attempt has been made to study equilib- rium [I] both with pure chormium metal and with chromium alloyed with iron, at temperatures between 1040o and 1300oC. From the work with the alloys it is possible to derive the chromium activities from the relationship

Jan 1, 1963

By Don Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern.. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and-steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a 'general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim' their own metallic wastes.

Jan 1, 1928