Search Documents

By William J. McCloy, Robert L. Gamble

A coal-fired fluidized bed steam generator rated at 12.6 kg/s has demonstrated the industrial and institutional application of fluidized bed combustion by burning high sulfur coal in an environmentally acceptable manner within a populated area. Designed to provide steam for heating and cooling, the unit was placed into service at Georgetown University in Washington, DC, and has already logged 5275 hours.* The unit has consistently operated well within Washington's strict regulations governing emissions of sulfur dioxide (SO2), nitrogen oxides (NOx), and particulates. The Georgetown program, cofunded by the university and the US Department of Energy, has shown that fluidized bed combustion is a promising way to realize the full potential of coal, the nation's most abundant energy resource. In a fluidized bed steam generator, a layer of granular limestone is placed on top of a grid designed to prevent particles from falling through. Air is passed upward through the bed with sufficient force to lift and float the particles. At this point the bed material resembles a boiling liquid. Crushed coal is then introduced into the bed and ignited. When high sulfur coal is burned, limestone absorbs the SO2 produced. The operating temperature of a fluidized bed steam generator is relatively low (approximately 871°C). As a result, NO, formation is minimal. Another potential problem encountered in burning coal is fly ash, a form of particulate. A feature of the fluidized bed design, developed by Foster Wheeler Energy Corp., is a fly ash reinjection system. Fly ash is reintroduced into the bed where it is burned again, thereby enhancing fuel efficiency. Nearly all remaining fly ash is captured by a baghouse dust collector. At Georgetown, the fluidized bed steam generator and all auxiliary equipment are enclosed in a structure aesthetically compatible with the surrounding university complex. The steam generator has two separate beds that can be fired independently, and operation to date has been with one and two beds in service, based on steam load demand. During several operating periods, when the fluidized bed unit was the only boiler in service, it supplied all the steam required by the 18.5 hm2 of buildings on campus. Initially fired with low sulfur coal, the unit was quickly switched over to higher sulfur fuel which will be used most of the time.

Jan 3, 1981

By L. Arbore

Introduction Mine operators are interested in energy conversation in two ways. With our finite sources of energy, we are concerned for future generations. In addition, as mine operators, we want to minimize energy costs. Moving material represents a substantial amount of the energy used in mining operations. Wheeled vehicles are used extensively to move materials. And they derive all their energy from fuel. Energy is also required to overcome the vehicle's inertia, and internal and external frictional forces. Included in the vehicle's frictional forces is its suspension. Tires are an important part of this suspension. What influence do tires have on the overall fuel consumption of the vehicle? Does tire construction affect this influence? As far back as 1896, it was apparent that tires were a factor in fuel consumption. A test was devised in France using a coal-fueled steam-driven auto. The test measured whether there was any fuel savings with the new pneumatic tires rather than of the then commonly used solid tires. The result was a 28% savings in water and a 29% savings in coal on pneumatic tires. Today, the pneumatic tire is accepted, but there are differences in present constructions. Tire Construction: Bias vs Radial There are basically two types of tire construction, bias and radial. Bias tires have been around for about 60 years. Radial tires are more recent. They were developed to improve a tire's ability to withstand higher speeds and loads, as well as to improve tire life and vehicle handling. Another advantage of the radial tire is its lower rolling resistance. This characteristic results in lower fuel use by a vehicle. This has been demonstrated with passenger cars and over-the-road trucks. It is now being demonstrated with earthmoving equipment. A basic description of both types of tire construction should now be reviewed: The casing of a bias-ply tire is made up of crisscrossed textile plies or layers. The cords of these plies run on a bias, from bead to bead. The cords of each ply run on an angle relative to the cords of the adjacent plies. As the tire rolls and deflects, the angle between the cords changes, like the blades on scissors (Fig. 1). The cords of one ply pull one way, and the adjacent ply pulls another, straining each other. This movement generates heat. Since the same layers of cords wrap around under the tread, they

Jan 9, 1984

DAVID COLE, El Paso, Tex. (communication to the Secretary*).-I notice that Mr. Callow takes issue with me on certain points I have previously contributed to the Transactions, to which I would reply," follows: Regarding Inspiration: Mr. Callow's refinements of gravity methods made just prior to the advent of flotation in the Southwest were intended to be "down to the minute," and the gravity flow sheet for Inspiration ores which he brought out at that time as the result of his long campaign of experimentation was regarded by many as the last word in wet gravity work. It was not my intention to discredit this good work when I said "he threw small light on slime treatment." "Minus 200 mesh," however, is not-synonymous with "real slime." Repeated treatments by gravity methods will result in the separation of a very large percentage of the fine granular sulphides in sizes much finer than 200 mesh, and I gave him due credit for that. The unavoidable losses were made in the "real" slime which I mentioned in the paragraph which Mr. Callow refers to as my "statements on page 1871," and his refinements were not a solution to the real slime problem. Mr. Callow has called attention to the fact that his best results at. Inspiration in gravity work were obtained on Joe Bush ore and he presents a table, viz., Tests Nos. 68, 71, and 72; and asks us to consider and compare these results, made by his refined gravity methods, with the results obtained by 'flotation methods in the new mill "during the second half of 1915 and in August, 1916." Of course, the ore treated in the mill was what happened to come. It was not Joe Bush ore, and therefore comparisons of detail figures are of no value. In regard to Mr. Callow's statements under the caption "Callow Cells Adopted by Arizona Copper Company," I would say that those who have been sufficiently interested to read my paper and' his remarks will notice what amounts to contradictory statements on several points which I cannot allow to go unchallenged. I was on the ground constantly and got my information at first hand. The tables published were the official ones. Mr. Callow was not present during the period and has been laboring under that disadvantage.

Jan 5, 1917

By W. H. Eardley

It is increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh—that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. Flotation Products Received At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent, lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent, moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent, moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain nodules and balls of unroast,ed concentrates, sulfur elimination

Jan 1, 1928

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days' wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011

By G. P. Walters, W. C. Fuller

THE production of thin films of beryllium became essential early in the irradiation program at Harwell in order to study the fundamentals of irradiation damage in this metal. In common with other metals, electron-microacope specimens of beryllium can be produced by different techniques. The techniques used to produce thin-film specimens varied according to the starting material. Most of the starting material was -0.060 in. thick. Large-area specimens (1 in. long by 0.5 in. wide) were chemically thinned to -0.005 in. thick in a solution containing 85 pct orthophosphoric acid, 10 pct chromium trioxide, and 5 pct sulfuric acid at 70°C prior to electropolishing. Small-area specimens, Fig. 1, had to be mechanically thinned prior to electropolishing because chemical thinning considerably reduces the area as well as the thickness. Mechanical thinning tends to produce a worked layer about 0.002 in. deep and hence this method cannot be used to thin bulk specimens below about 0.005 in. thick. Mechanical thinning is carried out by mounting the specimen on perspex then carefully polishing on wet grinding papers. Polishing is continued until about half the initial thickness is removed; the reverse side is then polished in a similar manner. After the bulk specimens have been mechanically or chemically thinned to -0.005 in. they are elec-tropolished in the solution shown in able I at 50" to 80°C. This solution should be prepared by adding the chromium trioxide to the orthophosphoric acid and then the glycerol last. The glycerol should be added slowly because a vigorous effervescence can occur. Electropolishing is carried out by holding the specimen in stainless-steel tweezers and gently agitating in the solution. Masking or "window" techniques are not required for beryllium, good microscope specimens being obtained from the edges of elec-tropolished foils. A stainless-steel beaker should be used, acting as the cathode and solution container. A closed circuit voltage of 30 v is used for polishing. Too low a voltage produces a matt surface and pitting occurs when it is too high. The solution temperature is important. If it is too low, the solution is viscous and bad polishing results and, if too high, etching of the specimen occurs. After electropolishing, the foils are thoroughly

Jan 1, 1963

By George Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell with certainty what mineral rights exist within any area that is not covered y patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared' up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, y a miner of the old school, as of no value. Think of the litigation over rights of possession on the Comstock lode-12 leading companies involved in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service-such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselves and their money at a safe distance,

Jan 7, 1914

By Charles W. Wagner

A premature explosion might be described as an explosion that, occurs before the miner expects it. Notwithstanding that it is unexpected, a premature is generally within the miner's control. A hangfire explosion is a blast that occurs after the miner expects it,, and in all instances, except where the explosives or blasting accessories are defective, hangfire explosions are within the miner's control. Causes of Premature Explosions Generally, there are seven methods of shot-firing in anthracit,e mines; namely: (1) cap and fuse with dynamite, (2) fuse with pellet powder, (3) squib with black powder or pellets, (4) exploders and delays with dynamite or black powder, (5) exploders with dynamite, (6) delay ignitors with black powder or pellets, (7) electric squibs with black powder or pellets. Cap and Fuse.—This method of firing seems to produce the greatest number of premature explosions. This is not solely because of the method, but is the result of mispractices which are possible with this method of firing. The two most common mispractices followed with cap-and-fuse blasting are the firing of multiple holes and the use of short fuse.. In the firing of multiple holes by cap and fuse, investigations have shown that in nearly every instance where the miner was injured by this method of firing he remained too long at the face lighting the several fuses, so that the first shot went off before he could reach a place of safety. Such accidents could have been avoided either by accurate judgment by the miner of the relative lengths of the fuses or by the use of electric firing. Rules exist in nearly every mine forbidding the lighting of more than one hole at a time where the cap-and-fuse method of firing is practiced. Where it is desirable to fire more than one hole at a, time, electric firing should be used. It is difficult to understand why so many premature explosions result from the use of short fuses, inasmuch as the cost of fuse is practically a negligible item in the expense of a day's work. Notwithstanding this, however, we frequently find miners using short lengths of fuse in an effort to save one or two cents per hole, or about 15 to 20 # in a day. A practice

Jan 1, 1931

By George W. Riter

OUR mineral-land laws need revising so as to provide definite title at the outset to the mineral deposits within any definite piece of land. The laws as they now stand, especially those applicable to lodes, breed uncertainty as to rights of possession prior to patent; and to my mind this is the worst feature of all, worse even than the apex bugbear. It is now almost impossible for anybody to tell-with certainty what mineral rights exist within any area that is not covered by patent, or whether any valid rights exist at all. Our system is unique in permitting individuals to appropriate and exploit mineral lands of the public domain without notice of any kind to the Federal government, and to relinquish them without any ceremony at all. The result is a clouded record that cannot be cleared up until each claimant is put to some sort of final proof. In order to accomplish this, new Federal legislation will be required. The requirements for a mineral survey and the proceedings for patent have always been cumbersome and expensive; and perhaps out of regard for the poor claim owner, who can ill afford the outlay for that sort of thing, the law does not require him to go. through it unless he chooses to do so. Consequently, every active mining district has become encumbered with tangled groups of doubtful or conflicting locations, whose rights and boundaries, when any valuable ore is found, must usually be determined by lawsuits that are as expensive and as distressing as the stakes are high. So deeply has litigation entered into our mining system that a claim whose rights have never been disputed would probably be set down offhand, by $miner of the old school, as of no value. Think of the litigation over rights of possession on the Com-stock lode—12 leading companies involved 'in an aggregate of 245 suits within a period of less than eight years! Ambiguous local records; the chance of erroneously placed or obliterated monuments; doubt as to the sufficient performance of the statutory annual labor; uncertainty as to prior conflicting or overlapping locations; anxiety as to the changing attitude of the Department of the Interior and the Forest Service—such considerations as these make an unpatented mining claim an unclean thing in the eyes of possible investors. Is it any wonder that they keep themselvesand their money at a safe distance,

Jan 1, 1915

By W. H. Eardley

IT IS increasingly evident that the excellence of blast-furnace operation to a great extent depends upon the preparation of the products fed into the furnace. The preparation of these products is carried on largely in the roasting and sintering departments. Prior to the building of flotation plants in Utah and other western states for the treatment of lead-zinc ores, the gravity concentrates received at the Midvale smelter amounted to about 4000 tons per month, containing 24 per cent. lead and 10 or 11 per cent. zinc. This product was about 20 mesh-that is, 45 per cent. of it would be plus 20 mesh and the balance minus 20 mesh. About 1000 tons of pyrite per month, containing 5 per cent. lead and 10 per cent. zinc, was also received. These products were sent to the multiple-hearth roasters for calcining, after which they were sent to the Dwight-Lloyd machines for sintering with other ores. The sintering charge passed over the machines but once. The first flotation products received consisted of a wet, sticky, muddy mass, containing a large amount of moisture, up to 19 or 20 per cent., and it was almost impossible to feed .them with any degree of regularity, if at all, through our standard feeders; but the amount of flotation product received during the first year or so was relatively small and it virtually lost its identity by being mixed with a large amount of jig and table concentrates. As the quantity of flotation products increased, more efficient filtering was accomplished and the moisture greatly reduced. FLOTATION PRODUCTS RECEIVED At the present time the Midvale plant receives about 4300 tons per month of flotation product running 60 per cent. lead and 4.5 per cent. zinc, 85 per cent. of which is minus 200 mesh and contains about 8 per cent. moisture; and 4000 tons per month of pyrite of similar fineness, running about 2 per cent. lead and 3.5 per cent. zinc, containing about 10 per cent. moisture. The lower moisture greatly reduces the difficulties of handling, making it possible to run a 100 per cent. flotation feed on a multiple-hearth furnace without serious mechanical troubles. The calcine, however, would contain-nodules and balls of unroasted concentrates, sulfur elimination

Jan 1, 1928

By Raymond J. Kujawa

For general purposes, insulating materials may be any of those mineral substances that provide a barrier between a desired human environmental feature and an unwanted condition. In this sense, radiation shields, electrical insulations, cryogenic insulation, and acoustical barriers would qualify. For this chapter only the thermal and acoustic insulations used for the median range of normal comfort control will be covered. Because of their magnitude and complexity the other fields are left to other chapters. In another sense, this section deals only with the ultra-lightweight aggregates and insulations, rather than the multitude of light-weight structural materials. Definitions and Uses The insulating materials covered in this chapter are the three groups of mineral products that provide thermal or acoustic barriers through the median temperatures encountered in home and industry. The three mineral categories are perlite, vermiculite, and the silicate wools whether they be categorized as glass, mineral, or rock. Perlites are those amorphous aluminum silicates with minor impurities that take the form of a felsitic, glassy lava possessing a pearl-like luster and concentric cracking. In a more commercial sense the term is used to describe either the natural or processed acidic, volcanic glass, containing from 2 to 5% combined water, that may be converted to a frothy mass by heating rapidly to the softening point. Vermiculites are micaceous, hydrated magnesium iron aluminum sheet silicates of varying composition. Commercial vermiculites are any of these sheet silicates that are capable of sufficient expansion on rapid heating to make an acceptable, highly porous product. Mineral wools, rock wools, silicate cottons, glass fiber are generic names for manufactured fibers in which the fiber forming substance may be slag, certain rocks, or glass. The fibers may be made by a blowing or spinning process. The resultant fibers may be felted or matted or gathered in the manner best suited to the use. The three groups may be used competitively to insulate ceilings and walls. The fibers have strong advantages in this area as they may be manufactured in batts that are stable in residential wall construction. The perlites and vermiculites are more suited to insulate cores and cavities of masonry walls and as plaster and concrete aggregates for thermal insulations. Vermiculite is widely used for insulating attic floors. Because of manufacturing techniques and controls, the glass fibers have made great strides as composites in the plastics industry but only a few of these uses classify in the insulation category.

Jan 1, 1975

By V. I. Purcell, S. C. Sun. R. E. Snow

A study including effects of 7) pH value, 2) fatty acid collector, 3) fuel oil, 4) interfering ion, 5) particle size, and 6) operational variables. Test results indicate feasibility of fatty acid flotation under certain restrictive conditions. FATTY acids have been used as standard collectors for floating the matrix1-8 but not the leached zone phosphate ores. After a series of investigations, Davenport9 and Tarbutton10 concluded that the Florida leached zone ores tested were unamenable to fatty acid flotation and must be upgraded by floating the siliceous gangue with Armac-T as collector. The cationic flotation was estimated11 to cost almost ten times as much as a fatty acid process that would ideally give the same flotation grades and recoveries of phosphates. Mineralization: Extensive deposits of leached zone aluminiferous phosphate occur in Florida."= The ore sample used for this work was obtained from the Virginia-Carolina Chemical Corp., Clear Springs area, Florida. The ore is a potential source of uranium and aluminum as well as phosphorus. Since the uranium and the recoverable aluminum are contained in some of the phosphate minerals, an upgrading of phosphate results in a corresponding enrichment of both uranium and aluminum. The phosphate minerals in the ore are primarily pseudo-wavellite, millisite, and carbonate fluorapatite, with a minor amount of wavellite. Quartz and clay are the common gangue minerals, quartz being predominant. Others present in small amounts are ilmenite, hydrated iron oxides, staurolite, monazite, and zircon. Experimental Procedures: After being dried to less than 1 pct surface moisture the material was dry-ground in a Hardinge conical ball mill to —6 mesh. The ground product was classified into 6/20, 20/200, and —200 mesh size fractions. On the basis of Table I, the coarse and fine size fractions were considered as phosphate concentrates, because of their high phosphorus contents. In contrast, the 20/200 mesh fraction, which was low in phosphorus, was used as the flotation feed. All the flotation tests, unless otherwise stated, were performed in a laboratory Fagergren machine under the following conditions: 1) 400 g of solid feed for each test, 2) 2000 rpm impeller speed, 3) 8.9 pH and 4-min conditioning, and 4) 3-min flotation. The procedure used for the quantitative bubble pick-up tests has been described previously.18

Jan 1, 1958

[The following notations will be used: O an ore body. W a sample of size w located in O; the size of this sample. W a block or a sample, of size W, located in O; the size of this block or sample. z' a point in W. W' a block or a sample, of size W' greater than or equal to W, located in O; the size of this block or sample. z" a point in W'. y (h) point semivariogram in O. s (h) point covariogram in O. In the previous chapter, we saw that the point semivariogram y (h) usually cannot be estimated directly from the data available. Rather, the values of samples of size w are available in O, and from these a regularized semivariogram y w (h) can be estimated. The following relationship has been proved (5.8): Y w(h) = Y (w;w+h) - Y (w;w). y (w;w+h) is the average value of y (z' z") when z' takes all possible positions in a sample w and z" all possible positions in a sample w+h of the same size, h being the distance between w and w+h. y (w;w) is the value of y (w;w+h) for h = 0, i.e. the average value of y (z' z") when z' and z" take all possible positions in w. We also saw that the regularized covariogram aw(h) is related to the point covariogram a (h) as follows (5.9): w(h) Gr In the following chapters, it will be shown that calculation of the average value y of y, or -a of a, in the general case relating to samples or blocks W and W' which need not be of the same size, plays a very important part in all the practical applications of geostatistical theory. The purpose of this chapter is to introduce various methods of calculating y and a-. Furthermore, mathematical equations and graphs are provided which can be used when the point semivariogram can be represented by one of the more common equations, and when the blocks W and W' are of simple shape. By definition (Fig. 6.1): [ ] Y (W;W) = WW f dz' f y (z' z") dz" (6.1) in W z" in W']

Jan 1, 1978

By D. D. Button, L. D. Jaffee

INTEREST in the use of graphite as a high-temperature engineering structural material has recently increased markedly. However, actual use of this material has been limited, in part because information about its high-temperature mechanical properties has been lacking. The information needed includes not only reliable values for the properties, but also how to control these properties. Malmstrom, Keen, and Greenl have reported on the tensile and creep properties of some graphites above 2700° F (1500°C). They observed measurable creep under tensile loading at 4000 OF (2200 °C) and higher, with elongations of about 7 pct at 4500°F. Their typical elongation-vs-time curve showed the normal three stages of creep found for many metals at elevated temperatures. The specimens used were heated by passing an electric current through them. This method of heating caused a significant difference between the surface and axis temperatures, and may have affected the results. More recent work by kattus, in which the specfinens were also heated by their own resistance, showed very little plastic deformation for either slow or fast tensile testing or for creep testing. Work at this Laboratory, already reported,3 showed that for temperatures above 4500 "F and under conditions of slow tensile loading some commercial graphites exhibited elongations up to 20 pct. The work reported here is the continuation of a study of the tensile creep behavior of some commercially available synthetic graphites at temperatures up to 5300°F, and is preliminary to a more systematic investigation of the variables governing the high-temperature mechanical properties of graphite. MATERIALS TESTED The tests were conducted on six blocks from four lots of synthetic graphite bearing four different commercial-grade designations. These blocks were selected because their tensile stress—strain properties had been determined in previous work.3 Table I pre- sents the available information, supplied by the producers, on the processing of these materials. Also included in this Table are the densities and the tensile strengths at room temperature and 4500°F determined by the authors. EXPERIMENTAL TECHNIQUE The furnace used to heat the specimens for testing is shown in Fig. 1. The heating element was a graphite tube, 3-in. OD by 2 1/2 in. ID by 24 in. length. A spiral was cut into the 6-in. center portion of this tube to provide a high-resistance sec-

Jan 1, 1961

By Fred H. Kan

The production of petroleum in Venezuela during 1931 was approximately 118,767,000 bbl., a decrease of 18,904,000 bbl., or 13.7 per cent, compared with the previous year. This is the first break in production, which has risen steadily since 1920, and is attributable to restriction of output and drilling operations, in harmony with lessened demand, rather than to any real decline in potential production. Venezuela ranked third among the world's producers, having lost second place to Russia. The Bolivar coastal fields, which were extended approximately 14 miles southward during the year, continued to supply most of the oil. La Concepcion, Los Manueles and Quiriquire all showed marked increases. A new field of light oil was discovered on the north coast near Puerto Cumarebo, State of Falcon. Exports declined 15.7 per cent, from 137,377,000 bbl. in 1930 to about 115,800,000 bbl. in 1931. Crude oil in storage at the end of the year amounted to 7,450,000 bbl., a decrease of 2,150,000 as compared with 1930. Tankage utilized is about 40 per cent of the available space. A drastic decline in drilling activity reduced the number of wells completed in producing areas from 401 in 1930 to 116 in 1931. Only three wells were drilled in the Lagunillas field proper, but, the amount of closed-in production and proven acreage gave assurance of a satisfactory potential output. Of the 1580 wells drilled to the close of 1931 in the producing areas of the Bolivar Coast, 631 were active and 853 were closed in; 96 had been abandoned. The status of the active wells at the end of 1931 was as follows: flowing, 331; pumping, 99; gas-air lift, 201. Producing wells closed in numbered 452; workovers, 8; totally inactive, 393. Lago Petroleum Corp. and Venezuela Gulf Oil Co. placed in operation the first units of their electric power plants, the former at Punta Gorda and the latter at Las Morochas, and are replacing steam power in their operations as rapidly as possible. Compressor stations were also installed for use in connection with air-gas lift operations. A considerable volume of gas was treated in gasoline extraction plants, the tail gas being recom-pressed and utilized together with natural high-pressure gas, for stimulation of production.

Jan 1, 1932

By Wayne E. Glenn

A centennial meeting should be a time to take stock, to evaluate performance, to plan ahead. It is like a line in a televised commercial that goes, "You've come a long way to get where you've got to today." And no less should be said of the mining and energy industries. We have come a long way. A hundred years ago when AIME was founded, this country produced 23 million tons of bituminous coal and 5.2 million bbl of oil. The figures in 1970 were about 580 million tons of coal and 4.1 billion bbl of oil. In spite of such accomplishments, serious and compelling voices are heard in the land - doubting sincerity, questioning corporate structures, and challenging ethics. Those doubts are raised in one part of Washington at the same time that other sections of the Capitol are asking us to produce more energy in order to keep up with population growth, emerging nations, and new technologies. Those of us in the fuel or energy business frequently talk about the race for energy. The question is, can we develop enough energy fast enough to outdistance our present and increasing demands? Recently I heard of an incident that - in an odd way - caused me to think of the energy race. The incident involved a sky-diver who jumped from an airplane without a parachute. He was handed a chute in mid-air by a sky-diving companion. He put it on, opened it, and landed safely. In a way, it seems to me that our society is hurtling through space and that it needs some help from the energy industries to land safely. We're doing our best, but under some rather difficult conditions. Because of illegal strikes and work stoppages the coal parachute is snarled a bit. The cut in percentage depletion and other tax changes have put some holes in the oil parachute. And the gas ´'chute has been in trouble for some time because of unrealistic controls on producer prices. The irony of the situation is that some of the very people who have been taking potshots at the energy parachutes for a long time are the ones who are complaining loudest now because the 'chutes are not functioning the way they could. The safety of the entire nation can depend on the energy industries.

Jan 1, 1971

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company's point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers' ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By Sanai Nakabe

Japanese wartime economy demanded domestic cobalt production. This paper describes a process operated for two years at the Besshi mine and smelter on extremely low grade (0.1 pct Co) pyrite concentrates obtained from copper ore. 'The steps in the process were roasting, leaching, precipitation, reduction fusion to crude cobalt, and finally refining by electrolysis to 99+ pct. COBALT ore deposits in Japan are all small and of poor grade. In the past, a small amount of cobalt has been produced from the best portions of a few of these deposits, and very little production is expected in the future. In addition to these lean cobalt ores, cobalt is present in the cupriferous pyrite which is fairly abundant although of low grade, as is shown in Table I. Considerable cobalt is expected from these deposits because of their extent. Cobalt cannot be exclusively recovered economically from ore of this type; however, if means could be devised to recover it as a byproduct of copper production, a fairly large production at reasonable cost could be expected from Japanese sources. It was along this line that the research work was done. Selection of Suitable Process The process for extracting cobalt differs from ore to ore according to their composition. The difficulty in cobalt metallurgy arises from the fact that chemically cobalt resembles many such common metals as Mn, Fe, Ni, Cu, and Zn, associated with it in the ores. In the present case the most serious difficulties were: 1—Extremely low grade ore, 0.1 pct Co. 2—The large proportion of iron accompanying cobalt and its close similarity in chemical behavior. 3—The fairly large proportion of zinc and manganese and their chemical similarity to cobalt. The recovery of cobalt oxide as a byproduct of the hydrometallurgy of copper had been attempted in Japan but was stopped after a short period because it proved uneconomical. The literature disclosed no method for the recovery of cobalt from cobaltiferous copper pyrite and it was therefore necessary to devise a new process. The following basic principles were considered in selecting the process: 1—A major alteration in copper production methods should not be necessary. 2—The first step should be the extraction of cobalt leaving the large quantity of iron unaffected. For this purpose wet metallurgy would be preferred.

Jan 1, 1952