Search Documents

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By F. Fraas

ELECTROSTATIC methods are used to separate and concentrate or purify granular particles derived from ores or various synthetic and agricultural products. Compared with other separation methods that require many technological refinements, the electrostatic attraction of fibers, grass, and seeds to charged surfaces clan be accomplished under the most primitive circumstances, and the early development of this method of beneficiation seemed very promising. Precise application of the method to provide high selectivity, however, is a complex procedure, and interest in this method declined. During this period Mr. O. C. Ralston initiated a Bureau of Mines research program oil electrostatic separation. It is the purpose of thins publication to describe the development of the electrostatic method of particle separation from the early beginning to the present resurgence of interest. Most of the information for this description bas been derived from references, a few of which were not available for thorough review. Much information has been drawn from the investitions of the Bureau. Acknowledgments Mr. O. C. Ralston, former Chief metallurgist of the Bureau of Mines, began the research program on the subject and did research on the mils literature. Both Mr. Ralston and Mr. H. B. Johnson, former president of the Huff Electrostatic Separator Co., furnished patent references. A critical review by Mr. F. D. Lamb, Research director, and Mr. M. J. Spendlove, Supervisory metallurgist, Bureau of Mines, College Park Metallurgy Research Center, lifts been of much value in preparing this report.

Jan 1, 1962

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By Olman Hee

This study investigates the identity and relative importance of factors affecting the future demand for phosphate rock, potash, and nitrogen. The main objective is to analyze demand relationships for these chemical raw materials for some specified past period, and to utilize this information to make projections of consumption into some designated future period. The end-use approach is used, which divides total consumption of each chemical raw material into agricultural, industrial, and export use. Multiple regression analysis is employed to statistically measure the relative effects of the different factors on consumption in each end use. The general method centers on the construction of a consumer demand model, the fitting of the respective equations in the model, and the interpretation of the statistical results. Direct and cross price elasticities of demand are computed for each end use of the chemical raw materials. These give an insight into expected changes in consumption with respect to given changes in price. The results of this study indicate that price, consumer income, and level of technology are factors which measurably affect consumption of chemical raw materials. For phosphate rock and potash, the agricultural and industrial end uses showed an inelastic demand, whereas for nitrogen, all end uses (including export use) exhibited an elastic demand. Among the chemical raw materials, average annual growth of consumption of nitrogen for agricultural and export uses to 1980 is expected to be notably higher than that for phosphate rock and potash.

Jan 1, 1969

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra rake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDR listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By William H. Mount

Since the late 19405, St. Joe has operated rubber-tired, trackless mining equipment underground in its Southeast Missouri Lead Belt operations. At first, the trackless equipment was operated in conjunction with rail haulage equipment in the room-and-pillar operations, but was to later replace rail haulage completely. The first pieces of equipment to travel on pneumatic rubber tires were short-haul shuttle cars of 12-ton capacity hauling rock from the heading to the mainline railroad. Early-model drill jumbos were the next pieces of production equipment to be carried on rubber, along with mobile slusher ramps. Mobile diesel equipment, in the form of conventional rear-dump trucks, made its appearance underground in the early 1950s, introducing the era of relatively high-speed mobile equipment as compared to the electrically powered shuttle cars. Haulage distances for rubber-tired vehicles were no longer dictated by trolley lines and trailing cables and tires were subjected to increasingly severe applications. St. Joe's first completely trackless mine, the Hayden Creek Mine, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and for the first time, an articulated diesel truck consisting of the tractor unit of a conventional earthmoving scraper and a rear-dump rock wagon. Those machines rolled on the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an In- creasing portion of the underground haulage today.

Jan 1, 1975

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By W. J. van Wyk, W. I. Mahne, G. Priest, C. du Toit, W. A. Liebenberg

Prior to the Coalbrook disaster in 1960, bord-and-pillar mining of the number two seam in the Witbank coalfields often resulted in small pillars with low factors of safety. At the Goedehoop Colliery, number two seam pillar stability is also affected by top and bottom coaling, while at Greenside Colliery, stability was further reduced by additional loading from a surface mineral residue deposit. This compromised the stability of the number two seam workings, impacting the safe mining of the overlying number four seam reserves. To extend the life of mine of both operations, an alternative risk management approach using designated enhanced monitoring districts was implemented to safely mine the number four seam reserves. This paper presents the use of geophone arrays to monitor micro-fracturing in number two seam pillars and the interburden between number two seam and number four seam, thereby enabling early detection of potential instability during overmining of the number two seam. Risk was assessed using fault and event tree analyses to determine acceptable failure probabilities. Automated seismic data processing distinguished micro-fracturing from noise, supported by extensive evacuation procedures for effective risk management. This approach facilitated the safe extraction of 4.70 Mt of number four seam coal. The study quantifies the efficacy of geophone monitoring in optimising coal recovery over low factors of safety pillars and assesses the application of Van der Merwe’s (2019) time-based formulae for pillar stability analysis for this project.

May 8, 2026

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By Maurice J. Peterson

THE VISUAL-ARC spectroscopic method of rapid qualitative analysis of complex inorganic compounds has been popularized in the past few years and is being employed by an increasing number of laboratories. The mineralogy and chemistry departments of several universities recently have added visual spectroscopy to their laboratory curricula. This revival of interest in a somewhat dormant analytical method has been stimulated through the publication of three papers 4 by members of the College Park staff of the Bureau of Mines. These virtually are the only recent sources of information on visual-arc spectroscopic analysis. They include data on the spectroscopic assembly, the analytical procedure, and the practical application of the method to determinative mineralogy and related fields. Requests for reprints of these papers continue to be received; at present only a limited number of copies are available for distribution. In order that these requests may be adequately answered, material from the three papers has been combined and, with some additional data, is presented in this bulletin. Numerous specific inquiries have been received regarding types of equipment available, problems in instrumentation, and information on the approximate sensitivity limits of the elements that can be detected by this method. Some of this material was not included in the original papers. Accordingly, the table of wavelengths has been revised to include the approximate visual-arc spectroscopic sensitivities, and a section on commercially available equipment has been added.

Jan 1, 1953

By Wilfred P. Sykes

AT intervals in the course of history an event occurs which, though scarcely heeded at the moment, marks in retrospect the beginning of a new era in some one field of human activity. Such a happening is perhaps more readily spotted in the field of technology than in other realms of human endeavor. Here the span of years is relatively short and the records have been kept with some degree of precision. In the current scene of our social and economic drama the art and science of metallurgy is playing a major role. Off stage will be found the metallurgist in one guise or another aiding, he trusts, in the development of processes and products which will contribute to the happiness of his fellow men. The results of his efforts appear in the form of metallic substances known as alloys built up from any two or more of the wide variety of metals which have been extracted from the mineral deposits in the earth's crust. An alloy by virtue of its inherent physical properties may seem ideally suited for human use in a special way but until this material can be produced economically it will fail to attain a place of prominence as an article of commerce. In fact many commercial alloys are being continually replaced by new or modified compositions better suited to meet the increasingly severe demands of industrial service.

Jan 1, 1939

By Tuanhui Wang, Qiwei Wang, Quanrui Liu, Jianhui Xu, Chao Wang, Yu Liu, Yuefeng Li

Rockburst is a highly destructive geological hazard that can cause casualties and equipment damage. To achieve highaccuracy discrimination of rockburst intensity, this article proposes an improved model that addresses the inefficient maximum membership principle used in traditional rockburst fuzzy evaluation models. The stress coefficient σθ/σc, brittleness coefficient σc/σt, and elastic deformation energy index Wet are selected as evaluation indicators for rockburst classification. Subjective and objective weights are obtained using the Delphi method and entropy weight method (EWM). Three types of membership function distribution forms are then used to obtain the membership degrees of each indicator to rockburst grades: trapezoidal membership function (TMF), normal membership function (NMF), and quadratic parabolic membership function (QPMF). Finally, six traditional models and six improved models are established using the maximum membership principle (MMP) and weighted average-maximum membership principle combination evaluation principle (WMP), respectively. Based on the analysis of 100 sets of rockburst field data, the accuracy, precision, recall, and F1-score of the improved evaluation model are increased by 11.3%, 0.097, 0.068, and 0.089, respectively, compared to the traditional model. The Delphi-NMF-WMP model is selected as the best model, with four performance indices reaching 97.0%, 0.979, 0.979, and 0.978. The best model is applied to evaluate the rockburst intensity of the Cangling Tunnel, Dongguashan Copper Mine, and Jiangbian Hydropower Station Diversion Tunnel, with evaluation results consistent with the actual situation, demonstrating the reliability and scientificity of the model.

Feb 28, 2024

By R Steven

"Surveying, and as a result, surveyors, have been around since the start of time, and it has been said that so has their methodology!The theodolite and tape have been the backbone of a time-tested practice that has led to ground breaking advancements such as electronic distance measurement (EDM), global positioning system (GPS) and positional laser scanning. However, it was the introduction of the unmanned aerial system (UAS) that has allowed mine sites such as St Ives to take the next step towards truly turning survey data into metadata.This paper will explain how the unmanned aerial vehicle (UAV) was adapted to meet the requirements of a mine site supporting a major open pit operation, and how the open pit mining team adjusted their planning and production processes to maximise use of the extra data and information available to them.The advantages of the system include point cloud surveys with corresponding large-scale up-to-date photography and computer generated high detail contouring of mined areas that are then incorporated into the mine plan. All the while, the use of the UAV must be tailored to each specific problem encountered and a solution then matched.Citation:Steven, R, 2016. Trials, Tribulations and Triumphs of Unmanned Aerial Vehicle Surveying at St Ives Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By George B. Clark

The purpose of this investigation was to determine the feasibility of designing and testing the elements of a small charge blasting system which will eliminate, or reduce to acceptable levels, most of the undesirable features of current underground drill and blast systems, i.e., 1) air blast, 2) ground vibrations, 3) flying fragments, 4) overbreak and fracture of surrounding rock, and 5) the cyclic nature of drill and blast operations. The experimentation was conducted in tunnels in granite and the results indicate that the basic technical concepts of the project were achieved. The next step is to design, construct, and test a prototype machine.

Jan 1, 1976

By D. W. Butner

The blast -hole method for drilling and breaking ground is not new to the mining industry . For several years it has been used rather extensively in Canada , particularly in the gold mines , where it was first developed and where the major advances in the technique as applied to present - day mining problems have been made . At present , 40 mines in Canada and the United States are using the method in one form or another , and from all indications its use will increase in the future . In two California mines , blast -hole diamond drilling is now used for a part of or for all stoping operations , and in one of these it is used to some extent in development work . At the Mountain Copper Co.'s Hornet mine in Shasta County, about 50 percent of the pyritic sulfide ore produced is mined by the blast - hole method , and the U. S. Vanadium Corp. mines 80 percent of the ore produced at its Pine Creek tungsten mine in Inyo County by this method . At Pine Creek , long -hole drilling and blasting is used for mining pillars also , and in pre - stoping development . The blast -hole diamond - drilling method is not applicable to all types of ore bodies . A third property in California , the El Dorado Limestone Company , El Dorado County, tried the method for several months in 1943 and 1944 , but , owing to certain factors that greatly increased mining cost , the company soon returned to conventional mining methods .

Feb 1, 1948