Search Documents

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By J Coombes

There is much debate on the Competent Persons qualifying criteria for providing classified resource estimates for public reporting. The CRIRSCO family of codes including the JORC Code, SAMREC, PERC and NI43–101, require Competent Persons to have at least five years ‘relevant’ experience and belong to professional bodies. These codes provide further, albeit vague, guidelines to assist individuals with their personal decision to take on the mantle of ‘Competent Person’. There is a risk, however, that these qualifying criteria can result in ill-prepared Competent Persons whose actions and recommendations would undermine their own reputation and that of the organisations that employ them; the integrity of the profession and the principles based reporting systems; as well as the stability of stock markets that rely on these estimates.Based on doctoral study on the development of professional competency within the mining industry, this paper presents an evaluation of the suitability of the current qualifying criteria as well as an analysis of alternative criteria. The research included a series of interviews with industry experts and an online survey of resource geologists. Semi-structured interviews provided a sense of experts’ expectations and interpretation of the current definition of ‘Competent Person’. The comprehensive online survey included a self-assessment, a series of situational questions designed to evaluate responses to typical resource geology scenarios and a set of open-ended questions relating to factors contributing to competency development.A summary of the data analysis, interpretation of the results and a set of recommendations for revised ‘Competent Person’ qualifying criteria are presented. This paper contributes to the conversation on what makes a person suitably qualified to report classified resource estimates and provides practical targets that can be used in the professional development of resource geologists.CITATION:Coombes, J, 2014. Redefining Competent Persons criteria for resource geologists, in Proceedings Ninth International Mining Geology Conference 2014 , pp 153–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017

By Y Yang, J Skrypniuk

The Jinfeng mine is Sino Gold's flagship project and is the second largest gold mine in China. Sino Gold Limited (SGL) holds 82 per cent equity in the Sino-Foreign joint venture Sino Guizhou Jinfeng Mining Limited (SGJML) with a Chinese partner. Jinfeng is located in a relatively remote site in southwestern Guizhou province. The orebody is considered to be the largest known Carlin type deposit in China. Jinfeng Plant has the world's third largest BIOX« bacterial oxidation facilities (790 t/d), treating highly refractory concentrate generated from crushing, semi-autogenous grinding (SAG) and ball milling and bulk sulfide flotation operations. The Jinfeng Plant construction started in February 2005, commissioning was completed in April 2007, and commercial gold production was achieved in September 2007. This paper describes the successful operations of Jinfeng Plant over the last two years. The key events of the project development are described, from the project background and process design, through to the commissioning and achieving design mill throughput of 3600 t/d resulting 180 000 ounces of gold per year. Process aspects of the BIOX« and carbon-in-leach (CIL) operations over the last two years are discussed which illustrate a very high BIOX« oxidation rate (more that 97 per cent) and excellent CIL recovery (more than 96 per cent). The management of the Jinfeng plant CIL tailings detoxification and filtration is described, and Jinfeng has became the first BIOX« processing plant to have achieved dry stacking of detoxified and pressure filtered CIL tailings. Current efforts to recover cyanide from CIL detoxified solution and the achievement of a zero discharge site water balance are also introduced. Many improvement projects have been made over the last two years which have culminated in a 15 per cent increase in mill throughput over the design and BIOX« CIL recovery increasing from 92.5 per cent to 96 per cent. Significant operating cost reductions from lowered of acid, lime and cyanide usage through process modifications and technical innovations are discussed.

Jan 1, 2009

By P. Roman, L. Daneshmend

"During the last decade, mining companies have been overwhelmed by technological solutions to perceived problems. This is particularly true with information technology where rapid advances have resulted in a professional climate characterized by technomania — the perception that failure to adopt emerging technologies will result in a loss of competitive advantage. This paper describes the applicability of structured analysis and design techniques as an appropriate methodology for integrating emerging technologies in the mining industry. The potential of this approach to improve overall mine effectiveness through improved communication and co-ordination between operations and maintenance is discussed. IntroductionA strong working relationship between the operations and maintenance departments in both open pit and underground mines is fundamental to the overall success of the mining endeavour. Unfortunately, for many mines, this characterization is far from accurate. Short-range production targets dominate the day-to-day management of the mines. This can be seen in Bostwick and Buchanan’s (1993) report on American Barrick Resources efforts to achieve an aggressive 415 000 tpd mining program at their Goldstrike operation in Nevada. When production managers do not meet their quotas, the finger is often pointed at maintenance. As a result, a confrontational culture can develop between the two organizations, resulting in a lack of cooperation that exacerbates the problem. Historically, production planning has taken priority over maintenance planning. This is reasonable since production is the primary purpose of the mine with maintenance serving in a support role. This basic relationship remains intact today. However, the trends toward mechanization, increasing levels of automation, and larger equipment, have resulted in increased reliance on the equipment used in the mine. As a result, downtime costs now go well beyond the direct labour associated with the repair of the machine. Lost production costs due to downtime resulting from failed equipment are becoming an increasingly important factor in determining a mine’s overall economic performance."

Jan 1, 2001

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018

By Cathy Aimone-Martin, Frank Achuff

The New Mexico Department of Transportation (NMDOT) and the Federal Highway Administration (FHWA) have let a contract to Sierra Blanca Constructors for a design / build contract along 38 miles US 70 in Lincoln County, New Mexico. The project will improve safety of travel along the corridor and facilitate the adopted economic development goals of the state. Proposed improvements include widening the existing highway from two lanes to four lanes, providing left turn lane options at selected locations, improving access for businesses and residences, aesthetically enhancing retaining walls, improving storm drainage and replacing the existing pavement with a 30 year mechanistic imperialistic perpetual pavement design. The US 70 Hondo Valley highway project is situated in a narrow valley with steep limestone walls, passes along a Scenic Byway and numerous historic ranching communities with structures that date back three centuries. The scope of work included requirements to monitor and mitigate blasting, noise, and vibrations. The contract was very presumptive with regard to blasting design and procedures. These included visual impact mitigation to treat and stabilize slope cuts, the Migratory Bird Treaty Act protecting roosting and nesting birds from airblast, and the protection of historic and cultural features such as acequias, wells, and structures. Public involvement affecting the rock blasting design has come from citizen task forces and committees concerned with highwall aesthetics and preserving the scenic byway and cultural resources. Constraints placed on the blasting program from agencies and the communities are often at odds. For instance, blasting must produce stable yet natural-looking walls to preserve aesthetics. Restrictions have been placed on pre-splitting and smooth-wall blasting yet safe slope are of the highest priority. This paper presents details of the design/build process undertaken by the contractors to conduct blast rock in an environmentally sensitive region. Blast designs consistent with good construction practices and used to comply with the many federal and state highway stipulations are described.

Jan 1, 2004

By A. H. Roberson, F. S. Wartman

For many years , it has been the common practice at most copper mines to recover copper in solution in effluent mine water by precipitating the copper with scrap iron.4/ The technique employed varies from simply throwing scrap iron or tin cans into the waste ditches to passing the water through elaborate launder systems containing detinned scrap and baled cans . In general , a considerable amount of low - cost copper has been recovered that otherwise would have been lost . Iron consumption usually varies from 1 to 1-1/2 pounds of iron for each pound of copper recovered . The grade of the precipitate may be as much as 90 percent copper.4/ ,5/ Where the consumption of iron is materially greater , its cost is likely to be the determining factor of profit . In times of emergency, when the demand for scrap iron for remelting increases the cost of the iron sharply, and the supply of tin cans is not large enough to meet requirements , recovery of the copper might not be economical . The three principal reactions that take place when an acid mine water containing iron and copper salts in solution is brought into contact with metallic iron are : (1 ) Copper is precipitated and an equivalent amount of iron is dissolved , CuSO4 + Fe Cu + FeSO4 ; ( 2) ferric salts are reduced to ferrous salts , Fe2 (SO4 ) 3 + Fe = 3FeSO4 ; and (3) the free acid in the solution reacts. with metallic iron to produce ferrous sulfate , H2SO4 + Fe = H2 + FeSO4 . = Because of the reported high.consumption of iron (5 to 6 pounds per pound of copper precipitated ), when copper in water from the Hornet mine of the Mountain Copper Co. ( California ) was precipitated upon scrap iron , a series of tests was made to determine . the . optimum treatment, time , and consumption of iron .

Feb 1, 1944

By RUSSELL S. DAVIES, Andrew Allan, John W. Buch

This is a progress report for the period February 1, 1949, to August 15, 1949, covering experiments with lightweight shearing machines for developing thin, steeply pitching anthracite beds. The over-all objective at the time an underground test section was established on July 30, 1946, was to improve mining above the gangway by developing methods for mechanization of pitch mining. Following the preliminary cutting tests in the gangway with the German machines, it became evident that the use of machines of this type indicated advantages for development work that could not be overlooked and warranted investigation. An agreement was reached with the cooperating company that this be done. Thus, the objectivo in the period covered by this report has been to obtain operating data to uso in comparing hand and machine methods of driving development openings. In obtaining the machine-mining data, 78 feet of gangway, 108 feet of heading, and 80 foot of chute work were driven. Hand-mining data are authentic for the mining condition. It has been shown that full mechanization is two and one-half times as fast as conventional hand methods on a lineal-feet- advance-per-shift basis and costs but little more than one-third as much. Tho machines are air-powered; there is less shattering of the coal bed by blasting; water sprays are used to allay' dust; coal is loaded by machine; no rock is taken; timber is not dislodgod by heavy blasting charges; and it may be said, except for the development of a means for transporting timber to the face, that the tasks for the miner are less arduous, and the working face equally as safe, or safer, than in driving by hand. Face timbering remains the greatest time- consuming cycle item, and steps are being taken to correct this. More than 50 percent of the cycle time is now usod for face-timbering work.

Jul 1, 1951

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By E. B. Spice

"IntroductionExperience at Eldorado has been gained with a variety of mill feeds. That is, the actual mode of occurrence of the pitchblende varies to such an extent that gravity concentration has at times been decidedly unattractive and at others highly successful. Because of this, the type of ore necessary for economic recovery of pitchblende have become well known. Also, those types which do not lend themselves to gravity concentration have become familiar. In general, it may be said that when the pitchblende occurs free, to a large extent, from sulphides or arsenides of high specific gravity, and when the bulk of the pitchblende is localized rather than disseminated, excellent recoveries, high ratios of concentration, and good grades of concentrates , will result from proper gravity concentration. On the other hand, if the ore contains pitchblende intimately or otherwise mixed with large quantities of arsenides or sulphides, or if the pitchblende is finely disseminated, gravity concentration alone will yield high recoveries only at the expense of very low-grade concentrates and low ratios of concentration.According to Taggart, the ease with which gravity separation may be effected is determined by the value of the following ratio: []It is stated that when the ratio is above 1.75, gravity separation can be expected to be easy. Thus with pure U308 (S.G. over 9) and gangue consisting chiefly of siliceous material, the process can he expected to be entirely successful even when carried on at very fine sizes. Unfortunately, the term pitchblende covers a great diversity of material. Although some of the mineral occurs pure enough to have a specific gravity of about 7, the average is much lower than this and is probably well under 5. Some of the pitchblende particles have a specific gravity so low that gravity concentration fails completely. It may also be said that no degree of grinding will produce free pitchblende of sufficient density from such particles. This, then, represents the most important limitation to the application of gravity separation to pitchblende ores."

Jan 1, 1950

By R. J. Evans

THE Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. PIOCHE ORE The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericite and graphite. The ore is an exceptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and are extremely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent. minus 150 mesh shows pyrite, sphalerite and galena still attached. EARLY ATTEMPTS AT ORE DRESSING Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore since 1913; in fact, a total of 35 commercial and plant laboratories experimented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effect a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-that is, about minus 200 mesh-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considered practicable at this time.

Jan 1, 1928

By James J. Gusek

The Atlantic City iron mine is located in Fremont County in central Wyoming, near the historic gold mining camps of Atlantic City and South Pass City. The mine lies on the southeast flank of the Wind River Mountains at an elevation of about 2,470 m (8,100 ft) above sea level (Fig. 1). An 81-h M2 (200-acre) tailings impoundment at the Atlantic City taconite operation has been a source of blowing dust. The site qualified for reclamation under Wyoming&apos;s Abandoned Mine Land (AML) reclamation program. The ultimate reclamation construction incorporated commercially available organic amendments and fertilizers into a 300-mm- (12-in.-) thick cap of a sterile clay loam cover material. The water level was lowered in an adjacent flooded mine pit that was feeding uncontrolled seeps into the tailings basin. A wide tailings pond spillway was built that allows flood control while minimizing seasonal water-level fluctuations in the pond. Rock berms and rock snow fences were built for wind-erosion control and soil-moisture preservation. Future work includes tree planting in the protective wind/ snow shadows of rock berms and rock snow fences and plugging a decant pipe. US Steel opened the Atlantic City iron mine in August 1962. It closed in 1983. Taconite iron ore was mined by surface methods. The ore was magnetically separated from the waste. The magnetic concentrate was mixed with bentonite, formed into pellets and roasted to produce a blast furnace feed stock for US Steel&apos;s blast furnaces in Geneva, UT. The pellets were hauled by rail to the Geneva Iron Works. The Atlantic City Mine produced three types of wastes. These included waste rock overburden from mining, a coarse-grained (sand to small-gravel sized), nonmagnetic reject rock termed "cobbs" and fine-grained tailings ranging from 600 to 75 µm (28 to <200 mesh). The waste rock has been used as an aggregate/rip rap source by a local contractor and the Wyoming Department of Transportation (WYDOT). WYDOT also

Jan 1, 1998

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By Yang Zhao, Wanping Wang, Siqing Liu, Shuming Wen

"In China, most reserves of rich iron ores have now been depleted and sustainable development of low-grade iron ores has become a critical discussion topic in the mining industry today. The aim of this study was to evaluate the applicability of beneficiating a low-grade, hematite-magnetite ore (assaying 18.64% Fe) for subsequent utilization. In this study, process mineralogy and beneficiation of the ore were carried out in the laboratory. First, mineralogical investigation shows that the main metal minerals are hematite, magnetite and a little octahedrite that cannot be used at present, and the main gangue minerals include albite, quartz and ankerite. Based on the above, a combined process of magnetic separation and gravity concentration has been developed by using laboratory low- and high- intensity magnetic separators and a slimes shaking table, respectively. Factors affecting these separation methods are discussed, including process mineralogy on the tailings of the high-intensity separator, where the iron minerals were found to be finely disseminated in the gangue as inclusions. By applying a two-stage grinding step and a magnetic separation stage together with gravity concentration, a marketable iron concentrate assaying 60.79% Fe at a recovery of 60.23% can be obtained, when the feed assays 18.75%Fe, which provides some useful information for the sustainable use of low-grade iron ore.IntroductionIron is the world’s most commonly used metal. Steel, of which iron ore is the key ingredient, represents almost 95% of all metal used per year, primarily in structural engineering applications and for maritime purposes, automobiles and general industrial applications. By the end of 2009, the iron and steel production in China ranked the first in the world, and reached 0.567 and 0.537 billion tons, respectively. The domestic supply of iron ore was 0.88 billion tons and about 0.628 billion tons of iron ore were imported in 2009."

Jan 1, 2015

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016