Search Documents

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By A. B. Young

In the original design of the flue system, the flues from the roasters delivered their gases to a large brick dust chamber which discharged into another flue with stack connection, as shown in Fig. 1. The treater is so situated that the gases are taken by it directly from the chamber and discharged again into the flue. The complete installation comprises two treater units, only one of which has been installed at present. The treater is essentially a flue 1.0 ft. high, 12 ft. wide, and 61 ft. long. (3 by 3.6 by 18.5 m.). Suspended inside, vertically and running lengthwise, are four banks of No. 20 corrugated iron plates; each bank is 10 ft. long, making an effective treater length of 40 ft. The spacing from center to center of the rows of plat,es is 9 1/8 in. (23 cm.) giving six-

Jan 1, 1921

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By Robert Glass Cleland

THE OUTBREAK of World War II found Phelps Dodge, thanks to both foresight and good fortune, in a position to increase production of its mines and factories to meet the insatiable military and domestic needs of the times, far beyond all previous records. With the timely completion of the expansion program at Morenci, the company's copper output rose to approximately 447 million pounds in 1942 and to over 478 mil- lion pounds the next year, compared to some 300 million pounds in 1939. To meet the civil and military needs for fabricated cop- per products, the Phelps Dodge Copper Products Corporation carried out an expansion program comparable in size to that of the Phelps Dodge mining operations. It built new plants, enlarged and reorganized those already in operation, multiplied the number of technical experts on its staff, adopted new methods and new machines for the new prod-

Jan 1, 1952

By Jarvensivu M, Ylinen R, Jamsa-Jounela S-L

The paper presents a new integrated system for control of concentration processes. The system is based on cluster-based modelling taking the ore quality into account and a new on-line particle size analyser capable also for reliable measuring of particle size distribution of concentrate. A metallurgical precontrol audit was performed at the Hitura concentrator in order to design the control strategy of the integrated grinding and flotation control. A new analyser PSI-200, was used to the measurement and control of the distribution of nickel in the total particle size range. An expert control system using the cluster model together with a new control strategy for decision of necessary control actions is outlined. The method has been tested to real data from mineral processes. The results are in good correspondence with empirical process knowledge. KEYWORDS: Cluster analysis, expert control, flotation control, mineral processes, modelling, particle size.

Jan 1, 1993

By David P. Lindroth

The heat content above 25.0° C up to 1,000° C was measured for six rock types: St. Cloud Gray Granodiorite, Holston Limestone, Sioux Quartzite, Rockville Quartz Monzonite, Salem Limestone, and the basalt at Dresser, Wis. The calorimetric data were obtained with an isothermal jacket-copper block calorimeter. The experimental heat content data for each rock type are presented, along with specific heat data obtained from the temperature derivative of the heat content. For the six rock types the maximum deviations of the specific heats at a given temperature were within 10 percent below 575° C and within 34 percent above 5750°C. The increase in the values of specific heat range from a minimum of 13 percent for the basalt at Dresser, Wis. (temperature range, 100° to 1,000° C) to a maximum of 46 percent for Holston Limestone (temperature range, 100° to 870° C).

Jan 1, 1971

By Hayward P. G

Complex ores, characterised by intimate intergrowths between minerals, have previously been treated by flotation with limited success. The most common problem has been that the liberation size is often finer than the lower size limit for selection flotation. A technique has been developed in which the problem is overcome by the use of a selective agglomeration procedure in which the values are coalesced with oil to a size suitable for flotation prior to introduction into the flotation machine. A complex lead ore was characterised by QEM*SEM mineralogy as having a mean galena liberation size of 15 ¦m. The best recovery of lead at 50 per cent Pb grade by standard flotation was 53 per cent. After application of the procedure, 86 per cent recovery was obtained after a single cleaner step. The oil functions as a bridging liquid in the presence of conventional collectors which render the mineral oleophillic.

Jan 1, 1991

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

Secondary or boulders blasting is a regular feature of quarrying operations in Pakistan, especially in cement and stone crushing industries. The main reason for secondary blasting is the production of a large number of boulders during the production blast. These boulders are larger than the feed hopper of crushers and require further breaking. The complex geometry of boulders, relative lack of restraining burdens, and the availability of number of free faces make this kind of blasting more hazardous than production blasting. Secondary blasts have generally unpredictable results and may cause flyrock, airblast, and over-crushing of rock material. Thus, it is essential to have an appropriate amount of explosive charge/powder factor, and for it to be properly distributed in the blast hole. The greater the amount of explosive over the required amount, the more violent is the blast, which will result in more flyrock, airblast, and excessive crushing of boulders.

Jan 1, 2012

By James F. Kemp

Discussion of the paper of D. Foster Hewett, Bulletin To. 27, March, 1909, pp. 291 to 310. JAMES F. KEMP, New York, N. Y.:-Mr. Hewett's paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally dis¬covered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit essentially asphaltite. The source and method of introduction afford a subject well worth serious reflection. Vanadium was first discovered and recognized as a distinct element in the slags obtained in smelting the titaniferous magnetites at Taberg, Sweden. For a long time, therefore, we looked upon the titaniferous magnetites as its hone. Analyses proved, years ago, that it was present in the ores of this type in New Jersey and in the Adirondacks. It was quite rarely determined, but when looked for it was, I think, invariably found, although the Amount seldom exceeded 0.5 per cent. of V,05., In just what combination it exists in the titaniferous ores is uncertain. One might imagine V2O3 replacing some of the Fe2O3 of magnetite; or, since in the lead series vanadates and phosphates are closely akin, one might wonder if a lime-vanadate could take the place of apatite. Yet no lime-vanadate has been found in nature, and apatite itself is usually rare in the titaniferous ores. When percentage-curves are plotted for a series of analyses of the ores, the line of vanadic oxide shows a curious sympathetic behavior with the line of chromic oxide;' but the data are somewhat limited, and no compound has sug¬gested itself which throws light on the matter. Dr. W. F. Hillebrand has discussed the occurrence and dis-

Oct 1, 1909

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By Luiz Felipe Mendonça de Amorim, Adimir Fernando Rezende, Gustavo Sampaio Lopes, Claudio Cesar Gajardo Arraño, Eltton de Sousa Veras, Manuel Villalobos Calderon

Many technical challenges were encountered while conducting near-field construction blasting between the critical intersection of Interstate 10 and multiple active railroad tracks in El Paso, Texas, for the Loop 375 Border West Expressway Project. Blasting was utilized for the removal of an andesite bedrock ridge in preparation for the construction of a new elevated super structure to be suspended over the existing railroad tracks. There was concern that the excessive vibrations and/or permanent rock deformation produced from the blasting within near proximity (20 feet, or 6.09 meters) of the railroad tracks would induce excessive stress and foul the tracks by shifting the alignment. This could result in a major loss of scheduling control between the two major railroad companies that operate in this area. There was also concern that the blasting may cause rock fragments to land on and interfere with critical interstate transportation. Blasts

Jan 1, 2019

By Cliff D, Harrison P. Hester C

During 1997 two different types of coal mine inertisation equipment were trialed in separate underground coal mines in Queensland.In April 1997 tests of the Polish developed GAG-3A inert gas generator were carried out at the Collinsville No 2 Coal Mine. These demonstrations indicated that the GAG-3A device was applicable in underground coal mines and that with respect to inertisation rate the device outperformed all other currently available techniques. The unit was assembled rapidly and operated safely during surface and underground trials and no mechanical problems were encountered with the device. The GAG-3A is not suitable for every fire scenario particularly if large volumes of fresh air are being drawn into the mine(where multiple units may be required), but with respect to the selection criteria developed by the Moura Implementation Process Task Group 5 criteria, the unit performed up to the specifications required.

Jan 1, 1998

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015