Search Documents

By G. M. Ritcey

Continuous contacting equipment for solvent extraction can be divided into two major areas, according to whether their mode of operation is stagewise or differential (Figure 1). Mixer settlers and the recent Kenics and Sulzer mixers typify the stagewise contactors. In these counter- current contactors, the aqueous and the organic phase are mixed and then separated in a large settling area before the next stage of mixing. Countercurrent differential contact- ors, such as centrifuges and various types of columns, are more compact in that they require less ground area than mixer settlers. [ ] Contactors, in addition to being either stagewise or differential, can be further subdivided into non-agitated and agitated depending on the method used for mixing the phases and producing the countercurrent flow. The simplest contactors such as spray, packed, or perforated plate columns achieve both the mixing and countercurrent flow by means of the gravity difference between the two phases. In agitated contactors such as the Scheibel, Reciprocating Plate, and Sieve-Plate Pulse, mechanical agitation is introduced but gravity differences still produce countercurrent flow. To conserve plant space, and for large throughput with short contact time, centrifugal contactors are used where possible. The reader can refer to reviews on the subject (1-11).

Jan 1, 1978

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By Maxwell HW

Pacific Coal Pty Limited (a wholly owned subsidiary of CRA Limited) managed the interests of six members of a joint venture formed to mine and export eight million tonnes of export quality steaming coal from a mine developed at Blair Athol in the Bowen Basin of the Central Queensland coal fields. The mine is now operated by Blair Athol Coal Pty Ltd. Crooks Michell Peacock Stewart Pty Limited (CMPS) was awarded a project management and engineering contract for the total mine portion. Following a feasibility study, CMPS carried out an Optimisation Study which produced changes to the design of the project, thus resulting in the project budget being reduced by some A$13 million. In spite of a number of late additions to the scope of work, the project was completed at a final cost of A$148 million, many millions below the reduced project budget. The project was also completed several months ahead of schedule. Total services were provided to take the project from feasibility stage through to the establishment of an operational facility and included project management, planning and control, accounting and financial control, as well as the organisation of engineering, procurement, construction, industrial plant commissioning, and technical training matters.

Jan 1, 1986

By W. R. Davison, C. A. Brown, J. P. Carstens

INTRODUCTION The phenomenon of heat-weakening of rock with 10.6 micron radiation from a continuous-wave C02 gas laser has been investigated in detail at the Massachusetts Institute of Technology for over 5 years. The programs at MIT have explored the basic nature of the heat-weakening phenomena and rock fracture caused by heating (e.g., Refs. 1 and 2), and have resulted in quantitative estimates of the relationship between the amount and parer level of heating and the resulting decrease in the modulus of rupture of a rock beam in a three-point bend test (Ref. 3). Results of the tests reported in Ref. 3 indicate a greater than 90% reduction in the modulus of rupture for granite beams heat-weakened by a laser. These results prompted the U. S. Department of Transportation to seek an assessment of the expected feasibility of employing the heat- weakening concept in a full-scale tunnel boring operation. Present- day continuous rock-tunneling machines have demonstrated tunneling time and cost savings over drill-and-blast methods, when used in rock types that are easily broken by the cutters. However, cutter bits have not yet been developed which can easily penetrate very hard rock

Jan 1, 1971

By Matsuhisa Y, Sakurai W, Shimazaki H, Peiming H, Fukahori Y

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skam Pb-Zn deposits in the Kamioka mining district, central Japan, where the wall rocks consist of heterogeneous rock units. The results (8180sMow of -1.1 to +17.3%o and 613CPDB of -5.0 to +4.8%o for limestones, and 8180SMOW of -0.8 to +12.5%c for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (180 and 13C) toward the center of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralization. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to- rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralization had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360m.

Jan 1, 1995

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By C. Bourgoin

"The limited development and application of new technologies to narrow-vein mining is currently impeding progress in the industry to a point where productivity, working conditions and operating costs have reached a critical stage in many Canadian mines.In an effort to foster the emergence and application of new technologies, Université Laval, together with other organizations, has carried out a R&D project focussed on the need of identifying new development pos5ibilities and of facilitating the transfer of technology in matters related to underground mining methods and machinery.The first phase of the study consisted of an in-depth assessment of current practices and problems in narrow-vein mining. The second phase was a state-of-the-art survey of mining methods and equipment, together with proposed modifications and innovations. The third phase of the project concerns the experimental development as well as the principal application of various proposed technologies.This paper presents an overview of the organizational, technical and strategic considerations which guided the University group and it serves as well to introduce a newly-published brochure, entitled ""Underground Mining Techniques of Vein Deposits"", which summarizes such work to date. More specifically, a perspective of technological developments applicable to narrow-vein mining is presented."

Jan 1, 1994

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

Provide the National Park Service (NPS) with guidelines for closing abandoned mine openings such as shafts and adits. Approach The NPS needed alternative methods of closing a variety of abandoned mine openings on National Park lands. Because the U.S. Bureau of Mines (USBM) has a long history of mining-related experience, the NPS requested that the Bureau provide them with technical mine closure information. USBM engineers compiled information on various types of mine closures and prepared technical illustrations of those closure techniques. Multiple closure options, by type of opening, were prepared as one-page field guides to assist NPS field personnel in determining the most appropriate closure method for a given situation and detailing the construction of the closure method. Results Guidelines provided to the NPS included a description of the method, use applications, construction techniques, technical illustrations, and technical support information. The following provides a brief description of 11 mine closure techniques identified for use by NPS personnel. Most of the closure methods, except the backfill methods, allow for construction that can provide access to the mine. However, providing access makes the closure susceptible to vandalism. Most closure methods require periodic monitoring for subsidence and corrosion or deterioration of construction materials.

Jan 1, 1994

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By Gerald J. Joy, Paul J. Middendorf

This study examines the patterns and trends in noise exposure documented in data collected by Mine Safety and Health Administration inspectors at U.S. coal mines from 1987 through 2004. During this period, MSHA issued a new regulation on occupational noise exposure that changed the regulatory requirements and enforcement policies. The data were examined to identify potential impacts from these changes. The overall annual median noise dose declined 67% for surface coal mining and 24% for underground coal mining, and the reduction in each group accelerated after promulgation of the new noise rule. However, not all mining occupations experienced a decrease. The exposure reduction was accompanied by an increase of shift length as represented by dosimeter sample duration. For coal miners exposed above the permissible exposure level, use of hearing protection devices increased from 61% to 89% during this period. Participation of miners exposed at or above the action level in hearing conservation programs rapidly reached 86% following the effective date of the noise rule. Based on inspection data, the occupational noise regulation appears to be having a strong positive impact on hearing conservation by reducing exposures and increasing the use of hearing protection devices and medical surveillance. However the increase in shift duration and resulting reduction in recovery time may mitigate the gains somewhat.

By Kurihara M

In Japan, shield tunneling method is generally used to drive a tunnel in sand layers around the urban area. In this report, appli- cability of NATM (New Austrian Tunnelling Method), which uses rock bolts and shotcrete as support, to water-bearing sand layers is studied aiming at establishing more economical tunnel driving technique. After the geological exploration, the conditions (i.e. pitch of steel supports, water content, cohesion, and fine content of ground,)necessary to ensure the face stability were investigated by using centrifuge loading tests. Concerning measures to manage ground water, an air permiability test was carried out to investigate the effect of the compressed air to cut-off inflow, and pumping test to study the applicability of dewatering. Furthermore, two dimensional elastic FEM analysis consider- ing progress of the excavation face was perform- ed to analyze stresses in the support system and deformation of the ground, and to investi- gate safety of the support and the ground. From these prior investigations, possibility of the applicability of NATM to the present pro- ject was predicted. Finally, based on these results, a real scale field application test was put into practice to confirm the prediction, and to pursue construction efficiency and phenomena which could not have been predicted Beforehand.

Jan 1, 1987

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By C. M. Frost

Crude shale oil produced during in situ retorting by the Bureau of Mines at Rock Springs, Wyo., was refined by three schemes. In the first, the crude oil was fractionated to raw naphtha and 400° F+ residuum. The residuum was hydrogenated over cobalt molybdate catalyst at 815° F and 1,100 psig. The blended raw and 160°-400° F hydrogenated naphthas were hydrodenitrified and then catalytically reformed. The 400° F+ hydrogenated oil was catalytically cracked. In the second scheme, the crude was hydrogenated over nickel-tungsten catalyst at 800° F and 1,500 psig. The hydrogenated fractions were processed by methods used in the first scheme. The third scheme resembled the second but, prior to hydrogenation, the crude was "hydrostabilized" over cobalt molybdate at 500° F and 500 psig. Yields of reformate and cat-cracked gasoline as volume-percents of the crude, and research-method octane numbers (with 3 ml TEL) for the three methods were as follows: First method, 32 pet reformate, 90 octane; 19.5 pct cracked gasoline, 99.2 octane. Second method, 29 pet reformate, 81.1 octane; 21.3 pct cracked gasoline, 99.6 octane. Third method, 28.2 pet reformate, 86 octane; 28.7 pct cracked gasoline, 95.9 octane.

Jan 1, 1974

By Norman Miskelly

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which include the requirement that a Competent Person prepares and approves publication of mineral resources and reserves. Most national regulatory organizations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organizations, and many dedicated individuals. The historical development of these standards is summarized in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of a Mineral Reserves International Reporting Code Template (International Template) that will be available for all countries to use in deriving their specific country reporting codes, are outlined

Jan 1, 2003

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 lb. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War II. A prospecting program disclosed reserves of over 25 million tons of graphitic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses.

Jan 1, 1945

By Barry A. Hillman

Respirable (PM-10) crystalline silica is regulated by the State of California as a carcinogen. The risk-management of this material by the State exemplifies the inherent problems in the development of regulations based on current risk-assessment practices. The influence of extremely conservative risk-assessment and risk-management can be expressed in economic impacts including the increased cost of production, reduced competition, increased prices, reduced employment and redistribution of income. This paper attempts to contrast theoretical risk- assessment and risk-management with current application using crystalline silica as an example. Based on health information pertaining to silica, the paper examines federal and State of California regulatory and public policy positions. Using current risk factors and empirical data for the Central Valley of California, the projected incidence of lung cancer in humans is examined. While such an analysis would project an extremely high incidence of lung cancer as well as silicosis, not a single case of either lung impairment has been recorded within the study area or throughout the world in the general population. This suggests that sound guidelines for the analysis of scientific information have given way to the assumption that virtually any information representing a substance as a carcinogen is to be considered valid with little or no qualification.

Jan 1, 1992

By W. H. Basssett

THE amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hamper that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen.

Jan 2, 1926