Search Documents

By J. A. Hillier

The staff of the Hudson Bay Mining and Smelting concentrator have developed a new type of reagent feeder. Several factors encouraged the development of such a system: varying heads caused by the mixing of ores from several mines, the increasing number of flotation circuits operated and reagent feeding stations remote from the flotation operator's work area. The reagent feeders also had to be compatible with future plans for reagent control from an on-stream X-ray analyzer and computer system. The new feeder is a positive-displacement pump set to deliver a constant volume per stroke. At a remote panel, the feed rate is altered by changing the time between strokes. The feeders have been found to be reasonably trouble-free and accurate to less than 2 per cent error.

Jan 1, 1973

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By AIME AIME

The first Diesel-electric locomotives for the Mesabi iron range of the Lake Superior district were put into service last summer by the Oliver Iron Mining Co., U. S. Steel subsidiary. There were ten of these locomotives, rated 1000 hp. and weighing 125 tons each. They are designed for service from 16 to 24 hours per day to haul trains of loaded ore cars from open-pit mines, 200 to 400 ft. deep, on a two to eight-mile haul to the top of the pit. The locomotives push or pull the trains over switchbacks and up heavy grades with 5 per cent maximum against the load. High tractive effort, less smoke, and ability to negotiate sharp curves were among the reasons for the selection of Diesel-electric locomotives.

Jan 1, 1941

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By AIME AIME

THE Federated American Engineering Societies through its Executive Board has endorsed House Bill 5230, introduced April 26, 1921, which provides for- the completion of the topographical survey of the United States. Before this bill can be reported out it will be necessary for the House Committee on -interstate and foreign commerce to hold hearings. This will not be done unless the engineers of the country show interest -and demand action which should be taken immediately after the recess ends and Congress reconvenes this fall. Surveys and maps have been made in this country ever since Captain John Smith mapped Chesapeake Bay about. 300 years ago, but it is only in comparatively recent years that the need for accurate maps has been keenly felt by those engaged in the industrial' and commercial development of the country.

Jan 1, 1921

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial' analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Patricio Zarate

Due to the intrinsic variability in orebodies, similar metallurgical behaviour of all material sent to the concentrator is expected to have some variability. Still some specific ores have anomalous performance which can severely impact on the concentrator’s production of metal, in this case copper. The study first will show the mineralogical characteristics of “usual ore” and of this specific “abnormal ore” which will have to be processed by the concentrator in the future. After that base conditions on both ores and flotation test procedure will be explained. Later the different alternatives tested regarding collectors and modifiers results will be compared. Finally, after discussing the different results with different reagents and considering operational variables of the concentrator, Floticor PD 702 is recommended to obtain the best copper recovery without increase in excess mass recovery.

Feb 1, 2025

By K. J. Miller

A two-stage froth flotation technique was developed in the laboratory to separate fine-size pyrite from coal. The process consists of the initial flotation of a 15-percent solids coal slurry with a minimum of frother; the coarse, free pyrite and other refuse are removed in the tailings. The froth product from this first stage is then repulped and treated with a coal depressant, a pyrite promoter, and a frother to float the remaining fine-size pyrite or pyrite attached to coal particles. With the two-stage process, the pyritic sulfur content of a Lower Freeport bed coal sample was reduced from 1.78 percent to 0.75 percent in the first stage, and from 0.75 percent to 0.27 percent in the second stage with good clean coal recovery.

Jan 1, 1972

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By Harry Morgan

ONE of the direct results of the increasing number of oil wells drilled to greater depths has been the development of new types of bits. These bits should resist the abrasive action of drilling and give the greatest footage before bit changes become necessary on account of dulled cutting edges. The loss of drilling time caused by changing bits becomes more important as the well becomes deeper, because the whole drill pipe must be unscrewed to make; each change. Under ordinary conditions the change takes: 2 1/2 hr. for round trip at 4000 ft., 3 hr. for round trip at 5000 ft., 4 hr. for round trip at 6000 ft., 5 hr. for round trip at 7000 ft. In other words, the time to change a stand of drill pipe (90 ft.) varies from 1 2/3 min. at 4000 ft. to 23 min. at 8000 ft. In general, the formation in the deeper zones is harder and dulls bits more quickly than the formations nearer the surface, therefore even a small increase of hole drilled per bit will decrease costs and increase speed of drilling.

Jan 1, 1929

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By R. D. Herron

Mining coal under deep cover conditions is certainly the proper phrase to use in describing one of our newest operations. Located in the southwest corner of Virginia is this operation which is the Beatrice Mine of the Beatrice Pocahontas Company, a joint venture of Republic Steel Corporation and Island Creek Coal Company. The mine is working in the No. 3 Pocahontas seam in an assigned area of over 9500 acres containing over 60 million tons of recoverable, high quality, low volatile coal. The site of the mine opening was at Keen Mountain, Virginia, where the seam lay 1350 feet below the surface. This depth, greater than anything attempted thus far in the coal industry on this continent, would pose some problems, we felt, with which we had not previously had to contend.

Jan 1, 1968

By Alden Greninger

METALLURGISTS have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel.

Jan 1, 1940

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

W. P. PUTNAM,. Detroit, Mich.-There is one company that is heating these tubes in an upright position by passing electrical energy directly through the tube itself. The lower connection is attached to an indicator, which shows the point at which the steel passes through the critical range At that point the clamps are released and the tube is dropped into a well of oil. This method simplifies the heat treatment of tubes in long lengths. H. J. FRENCH.-I am not entirely familiar with. the method outlined, but it appears to have one serious disadvantage; that is, the length of tubing that is directly connected with the electrical contacts is wasted and must be cut off due to either heavy oxidation or burning. That is a serious difficulty, if true in all cases, and cannot be overcome, inas-much as it is very difficult to draw long tubes of thin wall. Having once obtained a lot of tubes, to cut, say 14 ft. in length, there is often little excess metal available to discard. Am I correct concerning the burning or heavy oxidation of the metal where it comes in contact with the tube.

Jan 12, 1919

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994. Sensitivity analyses based on financial variables are now routinely applied to the forecast financial results of mining projects especially during the feasibility stage. Risk analysis is gaining acceptance but is still almost universally confined to the effects of variations in financial variables. The single most sensitive factor in almost all mining projects is the ore reserve, but it is either ignored or improperly used in sensitivity and risk analyses. Unlike financial variables, the components of the ore reserve (grades and tonnages of mining blocks) are a function of location within the orebody. Physical (mining) access to these components is therefore a function of time which has a crucial effect on forecast cash flows. It is critical that these fundamental concepts are included in risk analyses of mining projects. The effects are considered of the uncertainty of the ore reserve on feasibility studies and open-pit mine design for a small gold mining venture. Geostatistical simulation is used as a method of quantifying the risk in using grades and tonnages estimated from sparse data

Jun 16, 1905

By L C. Thompson

This paper examines six sites in Northern Nevada where soils and groundwater have been contaminated with petroleum hydrocarbons and/or organochlorine compounds. All six of the sites studied are located in an arid, highly mineralised area of the Great Basin. As a part of the original geochemical investigation to determine the applicability of biodegradation in the remediation of petroleum impacted soils and aquifers extremely high levels of uranium, vanadium and molybdenum were detected in the anaerobic groundwaters associated with some of the hydrocarbon plumes. Some groundwater uranium concentrations exceeded 7 ppm while vanadium and molybdenum concentrations reached almost one ppm. The bioleaching appeared to be most effective under methanogenic conditions and was noted in both high sulfide and low sulfide environments. Background concentrations of uranium in the formation were measured between 6 ppm and 109 ppm and highly dependent upon depth with the highest levels being found in association with evaporites. Unlike uranium, vanadium tended to concentrate in free-floating organic fractions reaching levels as high as 2000 ppm in the layers of jet fuel floating above the groundwater. Molybdenum was the most resistant of the three metals to bioleaching.

Jan 1, 2004

By Barry Cloutt

Western Mining Corporation Limited owns and operates the St Ives Gold Plant located near Kambalda, approximately 90 kilometres south of Kalgoorlie in Western Australia. Production commenced in March 1988 at a design capacity of approxi­mately two million tonnes per year. The plant was quickly expanded as a result of new ore discoveries in the district and has been processing ore since 1993 at the rate of three million tonnes per year. The plant has recovered over 50 tonnes of gold since the operation began, The plant was able to maintain acceptable recoveries throughout the plant expansion phases. Further gains in recovery were possible since there was still free gold in the tailings after approximately 24 hours of leaching. Testwork carried out on prospective orebodies showed that some contained considerable quantities of free visible gold, while others were seen to be semi­refractory using a conventional grind - leach circuit. Alternative treatment techniques were considered because a substantial amount of revenue was lost with the treatment of these ore bodies using conventional milling techniquies. The basis for all the investigations was to maximise the gold recovery from each orebody while minimising the effective cost per ounce of gold produced,

Jan 1, 1995