Search Documents

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

By Arne Westgren

ONLY in exceptional cases can the ordinary methods of chemistry be used for determining the constitution of compound metallic substances. Recourse has therefore been taken to special methods, the main expedients of which are, as we know, thermal analysis and metal microscopy. To these may be added-though more accessory-the determination of electric conductivity, specific volume, hardness or other properties. The information obtained by these methods has been compiled in equilibrium diagrams. Naturally, the technically most important alloys, such as steel, bronze and some others, have been subjected to very close study, and many investigators have devoted themselves to the solving of their problems of constitution. The equilibrium diagrams of these systems are therefore known today with a comparatively high degree of accuracy, even though it must be admitted that many details regarding their transformation reactions still remain to be completely explained. The equilibrium diagrams of the other alloys as a rule have not been determined so accurately. Most of them are based only on approximate determinations of the homogeneity ranges of the various phases. Thus extensive, detailed studies remain before these diagrams may be considered as established. Unfortunately, it must also be admitted that many of the alloy diagrams given in the present handbooks are as a whole very dubious. As a matter of fact, many of them may really only be viewed as the results of rather superficial, orientating investigations. In fact, there also seems to be a general opinion prevailing in our day that much work still remains to be done before the equilibrium conditions of the alloys may be considered as fully explained. At present, in almost all institutes for research on metals, as well as in many university laboratories, investigations to this effect are being carried out. As a rule, the classical methods of metallography, the thermal analysis and metal microscopy are applied.

Jan 1, 1931

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By Kevin Tallent

The use of military-type energetic materials in commercial explosive products is not a new concept. In the United States, the techniques for utilizing significant quantities of surplus military explosive materials by commercial explosive manufacturers dates back to the 1950’s. At times, explosive companies have found surplus military high explosives and propellant materials to be suitable ingredients for their commercial explosive products. The availability of these military-type energetic materials has varied over the past 50 years, as a function of the military’s strategic defense needs and the advances in modern weapon technology. For the most part, the commercial explosives industry has been able to implement methods for safely incorporating military-type high explosives and propellant materials, whenever these surplus materials become available. During the past 5-6 year period, a large amount of military-type energetic materials have once again become available for recycling into commercial explosives. This situation can be attributed to a number of factors, such as the political changes in Europe, the development of more sophisticated weapons systems, and the increased EPA pressures on the U.S. Department of Defense for disposing of surplus energetic materials. As in the past, U.S. commercial explosive manufacturers have made efforts to recycle these surplus materials into their explosive products. This paper describes some of the commercial explosive products that are currently on the U.S. market, which contain rocket and gun propellants as energetic ingredients. Some U.S. explosive companies, such as DYNO NOBEL, ORICA and Slurry Explosive Corporation, have been able to recycle significant quantities of surplus smokeless powder and composite propellants as energetic ingredients into their commercial Blasting Agents. The successes enjoyed by these companies have once again shown recycling into commercial explosive products to be an economically and environmentally sound method for disposing of surplus military-type energetic materials.

Jan 1, 2000

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By A. N. Winchell

In connection with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Ringham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance. • Sandstone-limestone Gradation The sedimentary rocks of the Bingham district are chiefly sandstones, with some beds of limestone, all now lying with their strike nearly east and their dip nearly north at an angle of about 30°, near the surface. The limestone beds are remarkably irregular in thickness in some places, but usually change very slowly in composition along the strike. However, the most interesting results are obtained from a study of a section across the beds at right angles to the strike. In some places, such sections show the usual alternation of pure sandstone with nearly pure limestone, in the simple manner assumed in most geological discussions.

Jan 1, 1924

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By J. R. Campbell

The need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. Washability Studies The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money can hardly be spent on "feed surveys') to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus. The sizes to be examined to get the picture are optional to the investigator. In modern wet washing, the range is from 4 to 0 in. Hand-picking on properly constructed belts is perhaps the standard for cleaning above these sizes. A good picture of the coal may be obtained by the following screen analysis: 3½ to 1¼ in. 1¼ to 3½ in. ½ to 5/16 in. 5/16 in. to 14 mesh 14 to 28 mesh 28 to 48 mesh and for very complete data on the fines: 48 to 100 mesh 100 to 200 mesh and through 200 mesh

Jan 1, 1930

By Albert Sauveur

The following propositions and corollaries are intended to present, as concisely as possible, some of the evidences gathered while studying the microstructure of steel. Each proposition is accompanied by photo-micrographs showing the structure of illustrative samples. But it must be understood that the special instances thus chosen for illustration are by no means the only ones on the examination of which the propositions are based. On the contrary, they have been taken almost at random among a great many, in some instances more than a hundred, similar cases. Proposition I. A slow and undisturbed cooling from a temperature x or higher produces crystallization. Plate L, Plate II., Fig. 1, and Plate V., Figs. 1, 2, 3 and 4 show the crystalline structure of several pieces of steel. Plate I. reveals this structure in the center of a slowly-cooled Bessemer ingot, 1.5 feet from the top. Plate II., Pig. 1, is from a small 2-in, square testingot of the same heat, slowly cooled. Plate V., Figs. 1, 2, 3 and 4 show the structure of different parts of steel rails. The original photographs were all magnified 70 diameters, and have been reduced in engraving to 63, or to 55 diameters, as shown in the plates. Proposition 11. Undisturbed cooling from an initial temperature lower than x is not accompanied by crystallization. Plate III., Fig. 5, shows the structure of a piece of rail-steel forged from a white heat until it had fallen to dull-red. The structure is almost amorphous. Practically no crystallization has taken place during the subsequent cooling. Corollary.—Pieces of steel finished at a temperature lower than x do not take a crystalline structure.

Jan 1, 1894

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Robert Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultimate cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development.

Jan 9, 1926

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By W. C. Roberts-Austin

The subject with which the Council of the American Institute of Mining Engineers has entrusted me is one of much interest. It has been so admirably treated in America by Prof. Carl Barus* that I should have hesitated to deal with it had not the adoption of pyrometric methods in England recently occupied much attention, especially in relation to metallurgical industries and research. I shall endeavor to show what is the present state of our knowledge of practical pyrometry by briefly tracing the history of the efforts which have been made to measure high temperatures. This paper will, therefore, be limited to the consideration of those forms of appliance which have either marked distinct stages of advance, or have remained in use with more or less modification through a considerable range of time. The earliest pyrometers were essentially thermoscopes, and although their graduation presented great difficulties, their importance as affording a means for the measurement of high temperatures has been recognized for centuries. It would be difficult to illustrate this better than by a brief record of the testimony which has from time to time been offered by those who have had to apply the heat of furnaces in research or in industry, and it is mainly for the sake of the light incidentally thrown on the progress of both that the following historical notes are offered. In the eighth century, Geber, the chemist, wrote a treatise on furnaces, and showed that he was familiar with many and varied means of applying heat; but he points to the difficulties that are met with in conducting operations at high temperatures, which he attributed to inability to measure heat, his actual words being: " sed quoniam non est res ignis, quae mensuari possit." t

Jan 1, 1894