Search Documents

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By S. Amirshenava, S. Nadimi

"Premature and unplanned mine closure can result in significant adverse impacts on the environment and community and need to be managed appropriately. Risk management techniques can reduce the negative impacts and risks of early mine closure. Risk Assessment 3D Model, is an efficient tool to quantify risk. The aim of this paper is to identify the mine closure risks in Choghart iron ore mine, and calculate the overall mine closure risk level. The result shows that 51.4% of assessed risks have low risk level and the overall risk level of early mine closure is low. Keywords: mine closure, risk assessment 3D model, Choghart iron ore mine INTRODUCTION The modern mining life-cycle can be divided into three main stages; exploration, mining (opening and production) and post mining (mine closure, and reclamation). Mine closure is the critical component of the modern mining life-cycle and it refers to the period of time when the operational stage of a mine has permanently ceases (Heikkinen et al, 2008). Planned closure occurs due to the depletion of ore reserves, but sometimes it is premature. Laurance (2006) shows that only 25% of mine closure in the past 30 years was due to resource depletion and in 75% of the cases the mines were closed for the other reasons. Ghanbari et al (2010) demonstrated that 48.6 % of copper mine closure in the past 100 years was due to resource depletion and 51.4 % of copper mines have been closed due to other reasons. The main reasons of premature mine closure are as follow (Laurance, 2006; Ghanbari et al, 2010; Maiti, 2013): • Economic, (low commodity prices or high costs) • Geological, (over-estimation of grade and tonnage) • Geotechnical (adverse geotechnical conditions) • Technical (equipment failure) • Regulatory, due to safety or environmental breaches • Social or community pressures • Closure of downstream industry or markets • Flooding or inrush Minaei Mobtaker and Osanloo (2013) developed a mine closure prediction model based on the data collected from closed iron ore mines in the past 100 years. They showed that economic factors, exhaustion of ore reserve and geological conditions are the main reasons of iron ore mine closure. They treated mine closure as a decision making problem in order to predict the causes of mine closure, including the uncertainties of some mine plan parameter such as iron ore price, production and consumption."

Jan 1, 2016

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By C. R. Everly

"The purpose of this paper is to review the most effective methods of reducing chloride transfer and chloride removal in the solution extraction and electrowinning (SX/EW) process. Elevated chlorides in electrolyte have various negative effects including a reduction in current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Historical controls that Sierrita has used to control chloride transfer, in order of effectiveness, have been chloride gasification at the EW that is directly correlated to amperage and chloride concentration in electrolyte, wash stage bleed and efficiency, width and velocity of aqueous bands, and electrolyte bleeds. Maintaining high bleed rates and high amperage settings has been a challenge with decreasing pregnant leach solution (PLS) grades, so keeping chlorides out of the electrolyte has become imperative. The effectiveness of reducing aqueous entrainment, optimizing wash stage efficiencies, and improving organic quality to reduce the transfer of chlorides to the electrolyte are illustrated in this study. INTRODUCTION The transfer of impurities from PLS feed streams to electrolyte in the Copper Solution Extraction process is a very common problem and is the reason that the wash stage exists in most SX operations. The main impurities affecting the SX process are iron, chloride, nitrate, and manganese. Elevated chlorides in the electrolyte have various negative effects including reduced current efficiency, increased handling costs at rod plants and smelters, increased anode corrosion, increased cobalt losses due to increased electrolyte bleed, degradation of HDPE piping, and increased corrosion in the SX/EW plants. Freeport-McMoRan Sierrita Hydromet is unique in that a high-chloride byproduct stream from the molybdenum process is pumped into the SX raffinate solution pond. This byproduct steam accounts for the majority of chloride introduced to the circuit, and over the years has built up to a point where 4000ppm chloride is consistently in the PLS feed to the SX. Concentrations of chloride over 70 ppm in electrolyte will result in downgraded cathode, so it is important to limit chloride carryover from SX as much as possible. Historically, Sierrita has been able to manage chloride levels with reactive techniques including increasing electrolyte bleeds and rectifier amps. Decreasing copper in PLS has made high amps harder to maintain, and increasing bleed rates have a direct impact on production goals."

Jan 1, 2015

By Sudip Basack

"The topic of pile foundation subjected to lateral cyclic load is an age-old problem confronted by Geotechnical Engineers. The environment prevalent in ocean and shorelines necessitates the piles supporting offshore and onshore structures to be designed accounting for the lateral cyclic loading resulting from the effects of sea waves. The quasi-static nature of this type of loading induces remarkable deterioration in the interactive performance of the soil-pile system. This can be manifested as progressive loss in pile capacity associated with increased pile head deflection. The work reported herein is aimed towards conducting rigorous theoretical analysis using finite difference technique so as to analyze the lateral cyclic loading response of a single, vertical pile embedded in cohesionless soil. The theoretical results are compared with the experimental results and reasonably good agreement is noted. This paper presents a brief description of the theoretical analysis carried out with some typical results and the relevant conclusions drawn therefrom. 1. INTRODUCTIONOffshore structures, namely, quay & harbour structures, jetties, tension leg platforms, oil drilling platforms, etc. are largely supported on pile foundations. Apart from usual loads from superstructures, these piles are subjected to continuous action of wave loading. This type of lateral loading is quasi-static cyclic in nature which results in considerable degradation in the interactive performance of the pile-soil system initiating progressive reduction in pile capacity associated with increased pile-soil stiffness. This may ultimately lead to disastrous consequences.Amongst limited research works in this field, the major contributions are made by Matlock (1970), Idriss et al (1978), Poulos (1982), Vucetic et al (1988), Long & Venneste (1994) and Basack (1999). A brief review of these works indicates that the degradation of the pile-soil system under lateral cyclic loading mainly depends upon the following parameters: number of cycles, frequency (cycles per unit time), cyclic load level (ratio of cyclic load amplitude to the lateral static ultimate pile capacity, in case of loadcontrolled mode) and cyclic displacement level (ratio of cyclic displacement amplitude applied at the pile head to the external pile diameter, in case of displacement-controlled mode). As pointed out by Poulos (1981 & 1982), the degradation is mainly due to: 1) partial to zero dissipation of excess pore water pressure generated during cyclic loading in progress, 2) destruction of interparticle bond with particle realignment and 3) rearrangement and gradual accumulation of permanent plastic deformation around pile"

Jan 1, 2005

By B. Farouk, D. Apelian

"A numerical model has been developed to predict the temperature history of particles injected in a low pressure d.c. plasma jet. The temperature and velocity fields of the plasma jet are predicted as a free jet by solving the parabolized compressible Navier-Stokes equations using a spatial marching scheme. Particle trojectories and heat transfer characteristics are calculated using the predicted plasma jet temperature and velocity fields. Correction factors have been introduced to take into account non-continuum effects encountered in the low pressure environment. The plasma jet profiles as well as the particle/plasma interactions under different jet pressure ratios (from underexpanded to overexpanded) have been investigated.I. IntroductionIn the plasma spraying process a d.c. plasma jet is used as a heat source to melt and accelerate powder particles which subsequently impinge and solidify on a given substrate. During low pressure plasma deposition (LPPD) prooess, the plasma jet is expanded into a low pressure environment (40-80 Corr) which results in high plasma jet velocities with Mach numbers ranging from 2 to 3. Previous efforts to predict heat transfer and fluid flow in plasmas have made use of incompressible flow formulation employing turbulence models [1-3] for atmospheric plasma spraying. However, these theoretical calculations have been limited to the subsonic flow regime; hence, the compressibility effects and viscous heat dissipation were neglected. In the LPPD process, the plasma jet is operated at the supersonic flow regime, therefore, the compressibility effects and viscous heat dissipation are no longer negligible. This is the main motivation of this work.In addition, production of high quality dense deposits requires that a large fraction of the injected particles be in a molten state when they impact the substrate. An additional motivation for this work is that it is important to understand the plasma/particle heat and momentum transfer since these phenomena dictate both the particle thermal history and particle trajectory.Early computational works in supersonic nozzle field flow [4,5,6] consisted of patching methods that divided the flow field into an invisoid free stream and a viscous boundary and. mixing layers. Each was analyzed independently and coupled through appropriate boundary conditions. Later schemes [7,8] involved solving time-dependent, compressible Navier-Stokes equations over the entire computational domain. These schemes show a great promise in predicting flows with complex structure, and where the viscous effects became prevalent."

Jan 1, 1986

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By Xie Zhang, Chongyang Zhao, Qingyun Huang, Bing Xie, Xiaopeng Zhen

"Extracting vanadium from vanadium containing hot metal into vanadium slag by BOF is the main vanadium production process in China. In this paper, the influence of Si content in hot metal on the quality of vanadium slag is analyzed. Synthetic vanadium slag with different SiO2 content were melted at 1673 K and then cooled to 303K at the cooling rate of 3?/min. Optical microscopy, SEM, EDS and XRD were used to analyze the mineralogical phases and crystallization behavior of vanadium slag. The results show that vanadium slag mainly contains spinel phase and silicate phase; V is enriched in the spinel phases while Si is concentrated in Fe2SiO4 CaFeSi2O6 and (Fe,Mn)2SiO4 as silicate phase. The melting point of slag increases gradually with the addition of SiO2; whereas viscosity decreases with an addition of 15~19% SiO2 and increases with an addition of 19~27% SiO2.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys. The major vanadium products include FeV, V2O5, V2O3, VN and Al-V-Ti alloy. Furthermore, vanadium slags are mostly produced by oxidizing the elements in V-containing hot metal during a duplex refining process. Therefore, the process of removing vanadium from hot metal has its significance on the subsequent process[1].The extraction of vanadium is greatly affected by the mineralogical composition of vanadium slag[2], the distribution of the elements between the spinel and silicate phases and its physic-chemical properties. These characteristics of vanadium slag have been studied in some details. It has been reported that Si mainly exists mainly in the form of silicate which wraps the spinel crystals while small amount of Si stands as phosphorus quartz or diopside[2]. Chen et al.[3, 4] points out, when SiO2 content in vanadium slag increased every 1%, V2O5 decreased 1.48%. Moreover, silicate phases would embarrass the oxidation of V-containing spinels through decreasing the exposing probability[5]. Meanwhile, melting point and viscosity of vanadium slag has been greatly influenced by the SiO2 content. Therefore, this work attempts to analyze the above-mentioned questions systematically."

Jan 1, 2012

By Ana P. Paiva, Marc F. Comella, Sandra S. Reis, Joao N. Reis, M. Soledade Santos

"In this work, the influence of the malonamide structure, acidity of the aqueous phase and diluent on the equilibrium interfacial tension (IT) of N,N'-dimethyl-N,N'-diphenylmalonamide (DMDPHMA) and N,N'-dimethyl-N,N'-dicyclohexylmalonamide (DMDCHMA) in 1,2- dichloroethane (1,2-DCE), and DMDCHMA in toluene, with aqueous HCl, were investigated. IT isotherms were determined using the Du N ouy ring method. Densities of the organic phases were determined, and used to screen solute-diluent interactions. Formation of third phases was never observed; furthermore, ITs increase with the phase separation period, constant values being obtained for separation periods larger than 1000 seconds. Each malonamide interfacial efficiency at the oil/water interface is interpreted in terms of malonamide basicity, diluent polarity and malonamide - hydrochloric acid- diluent interfacial interactions.IntroductionFor several years now, N,N'-tetrasubstituted malonamide derivatives have been extensively investigated as liquid-liquid extraction agents since they were first proposed as the organic components of the DIAMEX process, with the aim of advantageously replacing tributylphosphate in PUREX [1]. Therefore, a significant part of research studies with malonamides appearing in the literature deal with the extraction of major and minor actinides in real or simulated spent nuclear fuels in nitric acid solutions [2]. Under typical experimental process conditions, the tendency shown by some N,N'-tetrasubstituted malonamide derivatives to aggregate in the organic phase, leading in a few cases to the formation of undesirable third phases, has been remarked and consequently thoroughly investigated [3, 4]. The increasing use of chloride streams as hydrometallurgical aqueous feeds is becoming a reality, and this fact is obviously deeply founded on an extensive research carried out to recover value-adding metals from these media. Following this trend, a number of N,N'-tetrasubstituted malonamides have already been screened for the recovery of iron(III) [5, 6] and platinum-group metals [7] from hydrochloric acid solutions. The results obtained are quite promising either in terms of total metal ion recoveries or selectivity patterns achieved. The formation of a third phase when iron(III) was extracted by the tested N,N'-tetrasubstituted malonamide derivatives has never been observed under the adopted experimental conditions, and the extraction data collected would need to be reinterpreted accordingly if any aggregation phenomena involving the considered extraction systems were to take place."

Jan 1, 2011

By Daniel Bloomfield

ONE of the major problems of management is how to restore in some measure the personal relation-ship between employer and employed which, in the days of small concerns, meant better morale among employees. The complexity of industry today, the heterogeneous mass. of workers employed, many .of them new to this country and to its institutions, the inability of those whose task it is to get out production to spend much time on the problems of labor-all these and many other factors serve to make of great impor-tance the question of how to establish more satisfactory mutual good will. While there is no such thing as a sure cure for labor troubles, in spite of the fact that charlatans have been selling alleged cures to guileless employers, study and experience have brought to light methods of approach to the problems confronting management in its relation to labor that are well worth consideration. Labor problems must be approached with common sense and an open mind. Facts must be the basis of action. So it is with the question of morale in industry. What makes or breaks morale? What are the forces behind the actions of men? What is there in one man that makes him act differently from another man under similar circumstances? How are men affected by the actions of others in their own group or by the actions of those under whose supervision they work? These are questions that must be carefully studied if we are, to get at the bottom of industrial unrest. It is an easy thing to say that good will can be created by "treating men right." That involves so many things and points of view that it will hardly serve as a full answer to our problem; but it is a good starting point if we mean by right treatment the payment of wages consistent with the well being of the worker and his family as members of the community, and if we also mean the provision of sanitary, wholesome working conditions and a working schedule that does not overtax the worker physically, and mutuality-a give and take relationship. With this as a basis we can go a step farther and see what else can be done to promote better relations between management and the workers.

Jan 9, 1922

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

By Gerry Roblesky

"IntroductionWestar Mining Ltd. is Canada's largest producer of metallurgical coal for the export market. It currently operates two mines, the Balmer Mine at Sparwood, British Columbia producing 6 000 000 tonnes per year and the Greenhills operation at Elkford, producing 2 100000 tonnes per year. Approximately 1600 people are employed between the two mines which operate independently but share common administrative services.Like most mining companies in Canada over the past three or four years, Westar has faced rising production costs along with flat or declining prices and demand for its products. In order to survive under these conditions it has become necessary to strive for decreased costs in any way possible. Over the past two years there has been a widespread introduction of microcomputers across the company. In order to satisfy increasing demand for accurate and pertinent information while at the same time increasing productivity, the microcomputer has become an invaluable tool.This paper describes some of the problems faced by a mine maintenance department in this operating climate and how they were solved with the help of a microcomputer. It also describes some of the problems that may be encountered both with equipment and people and recommends some ways that these might be minimized or avoided. Finally, an assessment of whether or not the move to microcomputers was a current and economical one, and a brief description of future plans and projects is given.The Maintenance OrganizationIn order to appreciate fully the role that microcomputers are playing within the Maintenance Department at Westar Mining, a little background on the organization and operating philosophies is in order. Most of the comments apply directly to the Balmer operations, however, the Greenhills operation is similar in concept.The mine maintenance organization operates on a fleet based concept with these departments reporting to the maintenance superintendent: haulage trucks, shovels and drills, loaders and Caterpillar equipment, maintenance services, and rebuild services.Each of these departments is headed by an assistant superintendent and is responsible for all maintenance on the equipment on the respective fleet. Shift foreman, planners, specialists and clerical staff are assigned to each fleet. A central engineering and administrative group consisting of one engineer and three clerical positions is responsible for maintenance engineering and centralized administrative services"

Jan 1, 1988

By D. Harrington

Metal-mine fires in the United States are not of frequent occurrence and relatively for of those that do occur result in loss of life, although many cause heavy property loss or are costly to extinguish. Over a span of years, however, more lives are lost in metal Trines from fires than from any other of the untoward occurrences which afflict metal mining, such as electrical storms, floods, cave-ins, magazine explosions, or strikes. In perhaps more than 90 per cent of the fires. in metal mines' there is no loss of life; hence, the general public, even the general mining public, seldom hears of these fires, though the property loss frequently reaches hundreds of thousands of dollars; on the other end, in some instances the property damage from an underground metal-mine, fire has been negligible and the loss of life comparatively high. In any comprehensive study of metal-mine fires, ventilation is certain to be found a vital factor. The influence of ventilation on fires and the influence of fires on ventilation are of vital importance. In metal-mine fires very few persons meet death from actual contact Pith heat or flame; nearly all fatalities are duo to asphyxiation or suffocation. A well-planned, well-installed, and well-operated mechanical ventilation system is unquestionably one of the best available present-day protections from loss of life and property in case of fire in a metal mine; that this is true is attested by the usual helplessness of mining officials in trying to handled underground fires in a mine that has not had the foresight to install mechanical equipment to control underground air flow. On the other hand, the establishment of high-velocity air currents without sufficient day by day attention to such details as the method of coursing, or controlling, or confining them most certainly tends to increase dangers from fires rather than to aid in the avoidance or elimination of these dangers; the truth of this latter statement is shown by the fact that the greatest, loss of life in metal-mine fires during the past 20 years has been in relatively well-ventilated workings, and in every case the life loss has been due to some more or less trivial or easily remedied defect in the Ventilating system - usually a defect that has had some reference to doors used or supposed to be used to deflect or control air currents.

Jan 1, 1933

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By Nageswararao K

A series of tests was carried out on one of the rock-pebble milling circuits treating complex nickel ores at Kambalda Nickel Operations of Western Mining Corporation. A mathematical model to describe the behaviour of a 508 mm hydrocyclone was developed from the data.A "flat" reduced efficiency curve was observed for the system. This was attributed to a marked difference in the specific gravity of different size fractions of the feed. A modified approach in describing the shape or the reduced efficiency curve resulted in accurate prediction of the hydrocyclone performance.

Jan 1, 1981

By K. Morsi, S. K. Kassegne, K. S. Moon, A. Numula

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based manufacturing of macro, micro and possibly nano-scale features and shapes. CATS enables the selective sintering of powders by localizing current activation conditions through an electrically conducting small tip (either in the stationary or moving mode). This paper presents preliminary experimental results on the CATS of reactive mixtures of Ni/Al powder to form nickel aluminide intermetallics. Preliminary investigations on the effect of current on the reaction characteristics are discussed.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [1,2, 3,4,5,6]. The process boasts remarkable advantages which include ultra fast heating rates (hence by-passing low temperature non-densifying sintering mechanisms), considerably lower sintering temperatures and shorter sintering times than achieved in conventional sintering. The process is however limited to the generation of simple geometries on the macro-scale. Recently three of the authors conducted work on a novel process ""Current-activated tip-based sintering (CATS)"" [7], where electric current is passed through a conducting tip that is placed or allowed to travel over a powder bed/compact to locally sinter powders. lD, 2D and 3D micro-scale sintered shapes can be generated with the possibility of 3D rapid prototyping on the macro/micro or nano-scale. Although CA TS of single phase powders has been conducted, the CATS of reactive powders has not yet been investigated.The Ni-Al phase diagram contains five intermetallic compounds, AhNi, AhNh, AlNi, AhNi5 and NhAl. Out of these intermetallics, NiAl and NhAl have received the vast majority of scientific and industrial interest [8]. NhAl can be formed by reaction synthesis, where nickel and aluminum reactant powders are heated to a reaction ignition temperature at which the reactant powders are converted to the intended intermetallic product. The reaction is exothermic which gives rise to considerable compact self heating, thus instantaneously raising the compact temperature by several hundred degrees which facilitates sintering [8]. Applying and electric current locally would not only provide for a rapid local reactive sintering, but would generate a number of intriguing scientific investigations. For example, of interest would be, how would the reaction propagation and microstructural/phase evolution be affected by the temporal and spatial temperature and current distributions."

Jan 1, 2011

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015