Search Documents

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986

By N. A. Tiner, Saara Asunmaa

The early stages of nucleation of vacuunz-deposited gold coatings on electropolished surfaces of pure nickel and binary alloys of Ni-A1 and Ni-Ti have been studied, employing carefully controlled temperature and vacuum conditions. The preferential nucleation of gold on slip-plane edges on the crystal surfaces gave rise to a very pronounced decoration effect which was used in studying the morphology of the pain boundaries, etch pits, and slip planes on crystal faces. Characteristic surface patterns were observed with local dimensional variations. Most pronounced geometric patterns were ohserved in the pain boundaries of nickel and on the crystal faces of Ni-A1 alloy. The nucleation behauior of gold indicates contamination on the Ni-T1 alloy and the getter properties of titanium are presented as a tentative interpretation for the detected contamination. The markings and imperfections on cleavage surfaces of crystals have long been observed by optical microscopy.1,2 Surface-replica techniques are also used to detect the smallest steps and structural details on crystal surfaces by electron microscopy. Recently, Bassett3-5 and Sella, Conjeaud, and Trillat 6 have shown that, when gold is deposited onto a rocksalt cleavage surface, there is preferential nucleation at steps and slip-plane edges on the crystal surface. This gives rise to a very pronounced decoration effect which is invaluable for revealing the lattice steps on a cleavage surface. According to Bassett,3 gold atoms arriving during vacuum evaporation at the crystal surface have a certain mobility on the surface after arrival, particularly at elevated temperature. If a significant

Jan 1, 1964

In the stability assessment of open pit walls, geotechnical engineers have to deal with uncertainty related to structural geology, rock mechanical parameters, groundwater and so on. This uncertainty will immediately and significantly impact on wall stability assessment and therefore. influence mineral recovery and ultimately the financial return of open pit mining. However, the conventional factor of safety applied to measure the stability of slopes and the relevant analytical computer packages cannot quantitatively consider the variability or uncertainty of the input data. As a supplement, therefore, geotechnical engineers have begun to apply probability to the stability assessment of open pit walls over the last two decades. To-date unfortunately, no powerful computer package is available to geotechnical engineers to conduct the probability analysis of slope stability. This paper presents a computer package of probability analysis for rock and soil slope stability. In this computer package, the strength parameters of rock and/or soil material such as cohesion, friction angle and unit weight of the different rock and/or soil type domain in a complex structural geology environment can be considered as the basic input random variables. Groundwater level can also be taken into account as a random variable in this package. Two `rigorous' limit equilibrium solutions, the Morgenstern/Price method and the Sarma method, can be used to calculate the factor of safety during Monte Carlo Simulation applied in this program. Five types of probability distribution are included in this package for the user to simulate basic input random variables. Two realistic cases from BHP Iron Ore are used to illustrate this package.

Jan 1, 1997

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By E Yll÷, O HyvSrinen

Outokumpu has developed a new chloride leach process, called HydroCopper«, to treat copper concentrates. Chalcopyrite is quite refractory in leaching and in sulfate milieu an autoclave of high temperature and pressure is required. However, in the HydroCopper«-process copper sulfides can effectively be leached in atmospheric pressure using strong, aggressive chloride solution and copper (II) ions as oxidant. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride formed in precipitation is decomposed in a chlor-alkali electrolyser, the products of which are circulated back to the process: sodium hydroxide to copper (I) oxide precipitation, chlorine gas to leaching and hydrogen gas to the reduction of copper (I) oxide. During 2003 - 2004 the performance of the HydroCopper«-process was confirmed in a demonstration plant processing one tonne of copper per day. It has been found to be applicable for different kinds of concentrates and can also tolerate a wide range of impurities. A significant advantage of the process is that gold can be leached as a chloro-complex and recovered with active carbon. HydroCopper« can economically recover copper from concentrates and process to a cast copper product. The best utilisation of the process is in most cases achieved when the plant is situated at the mine site. Higher recoveries are attained by the optimisation of the whole operation chain from the mine and the concentrator to the HydroCopper« plant.

Jan 1, 2005

By Brian E. Travis

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to steel. The finished polymer mining grid product is a viable alternative to conventional supplemental roof control meshes such as chain link fence and welded wire. Polymer mining grids are a fraction of the weight, have comparable load support qualities, and will not rust or corrode in even acidic or alkaline conditions. Specific flame retardant additives can also be incorporated to make the polymer grid self extinguishing for use in underground "gassy" environments.

Jan 1, 1992

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By Garland W

Access to geoscience reference informa- tion including mining and mineral processing has increased considerably in the last five years in Australia. This has been due principally to the use of computer-based information storage and retrieval systems. The main reference data base for the mineral and petroleum industries and disciplines in Australia is the Australian Earth Sciences Information System (AESIS), cooperatively developed and coordinated by the Australian Mineral Foundation (AMF). AESIS is created on the CSIRO computing network (CSIRONET) which has a CYBER 76 host computer located at the CSIRO Division of Computing Research (DCR) at Canberra. Data entry was until recently carried out by AMF using a dedicated line through the Adelaide CSIRONET node to the CYBER 76 interactive system. Data entry is now done directly at the AMF on a DEC PDP 11/44 mini computer that is also a host work station on CSIRONET. Data collection via magnetic tape media input from other computer-based systems is under development. The software used for data entry and management of the data base was developed by CSIRO CILES Systems Development Group. For public interactive online use the AESIS data base is transferred by tape to AUSINET - the Australian information net- work run by ACI Computer Services, Melbourne, where the data base is converted to a form suitable for the IBM STAIRS software. CSIRO facilities at DCR Canberra are used to produce computer type-set camera ready products and output in microform, on magnetic tape or as graphic display. Keywords: Earth sciences information, Computer applications, Information storage and retrieval, AESIS, Data bases, Australia.

Jan 1, 1983

By F. B. Plummer

THE physical properties of oil-producing sands, such as grain size, porosity, and permeability, are becoming more and more important in petroleum production engineering as oil fields are being repressured and rejuvenated. A number of excellent papers have been published recently on all three of these properties. Faucher, Lewis and Barnes1 give a com-plete survey of the work done through 1932 and contribute also much information on sands that they themselves have examined. Muskat and Botset,2 Wykoff, Botset, Muskat and Reed,3 Hurst,4 and Muskat5 have contributed a great deal to the theory and actual measurement of flow of liquids and gases through porous media. Muskat and Botset have measured the permeabilities of different sands with gases and liquids. They find that the radial is always slightly under the linear permeability. However, in most of the previous experiments small samples of the sand were used, and the method of production of fluid or gas through the sands has not been very close to actual oil-field conditions. In addition, so far as the authors are aware, no measurements of linear and radial permeabilities have been made simultaneously under exactly the same conditions. The multiple permeability apparatus described here is a part of the equipment being acquired by this laboratory for thorough investigation of the physical properties of producing sands. It possesses certain advantages for comparative studies of liquid flow. Additional data and descriptions of other instruments will follow in papers to be written later on. The essential features of the permeability apparatus are as follows:

Jan 1, 1934

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By Tao Li

The development of DP(Dual Phase) steels and TRIP(Transformation Induced Plasticity) steels has received much attention in recent years due to their high strength and simultaneous good ductility, which provides the potential for weight reduce and resource savings on certain components in automobile or other industries. So a controlled rolling process was simulated in the present study by thermomechanical simulator (Gleeble 1500) for producing DP steels on a kind of low carbon steel containing a small amount of Si and Cr. F+M dual phase microstructures have been obtained during continuous cooling processes of a wide cooling rate range from 10°C /s to 60°C /s. The grain size of the dual phase steel developed can be refined to less than 5 m through the mechanism of deformation induced ferrite (DIF) transformation. The ultrafine ferritic grains are equiaxed with high-angle boundary, and the martensite islands of an average size less than 5m disperse uniformly in the ferrite matrix. The ultrafine martensite islands not only inhibit the growth of ultrafine ferritic grains and improve the bonding of F/M interface, but also increase remarkably the strain hardening rate in the processing of the present Dual-Phase steel. As a result, the tensile strength of ultrafine grained Dual-Phase steel reaches higher than 1000 MPa. The result shows that an ultrafine grained Dual-Phase steel of low carbon and low alloy is promised to exhibit desired F+M microstructure by means of this new TMCP process.

Jan 1, 2006

By J. A. Harrison

The physical composition of coal and the distribution of its physical constituents will partially determine the efficiency of the process chosen for coal preparation. Distribution and concentration of coal macerals will, to a degree, be controlled by preparation processes. A number of preparation processes have been evaluated to determine this interrelation. These evaluations will help provide information needed for the production of coal that meets definite petrographic composition specifications. etrographic composition and degree of coalifica-tion of coal can determine the choice of cleaning processes and equipment used in coal preparation. The purpose of this paper is to present data on studies of the preparation processes of breakage, sizing, cleaning, and blending and to show the effect coal's petrographic composition has on these processes. Herrin (No. 6) and Danville (No. 7) Coals from Illinois were used in these tests. Nomenclature used herein is that approved in the Glossary of the International Committee for Coal Petrology,' based primarily on the Stopes-Heerlen system of classification2 and used in coal petrography laboratories throughout the world. BREAKAGE TESTS Breakage tests of Illinois coals related to petrographic composition have been conducted at various times at the Illinois State Geological Survey. These tests have been classified under two headings -impact tests and compression tests. Impact tests, as the name implies, consisted of breaking the coal by a sharp, sudden force. Impact tests were further divided into fall tests and block tests. Compression tests consisted of applying a constant pressure on a piece of coal until the coal fractured.

Jan 1, 1963

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By Jan Butra

In copper ore mines located in the Pre-Sudeten Monocline the deposit mining using room and pillar systems has been carried out for more than forty years. When implementing mining systems in deep copper ore mines it appeared to be necessary to adapt them to variable geological conditions and natural hazards. In the initial period of exploitation there were mainly caving and rockburst hazards. The adaptation of room and pillar system was connected with a state of knowledge in the scope of identifying, forecasting and controlling rock mass hazards. The new solutions allowed the safe and efficient exploitation of a blanket deposit of variable thickness from about 2 to 15m, seated on progressively increasing depth. They included exploitation in constrained conditions, such as in protective pillars. In the exploitation period, technical and organisational activities aimed at rockburst hazard control were introduced including active methods for controlling rockburst hazard and procedures for conducting mining works in the rockburst hazard conditions. When mining at a depth exceeding 1,200 m, the exploitation method and technique are additionally affected by thermal hazard and by gas and rock breakout hazard. New solutions of the room and pillar system and a longwall system with mechanical mining have been developed for exploitation in the associated hazard conditions. The require application of many innovative solutions in the scope of mining process and ore haulage mechanisation, excavation support and forecasting and control of existing hazards. The main purpose of these solutions is to conduct the safe and economically effective exploitation of the deposit.

Aug 1, 2013

By A. L. Holloway, N. M. Soonawala, L. S. Collett

"Since the late 1970s, a major R&D program has been under way in Canada to assess the concept of disposing of nuclear fuel wastes in deep plutonic rock. Atomic Energy of Canada Ltd . (AECL), a federally-owned corporation, has been given the responsibility of directing this research (Rummery et al., 1983).The Underground Research Laboratory (URL), constructed in a granite pluton 15 km east of Lac du Bonnet, Manitoba (Fig. 1) is a major component of the Canadian Nuclear Fuel Waste Management Program. A diverse geotechnical experimental program is being carried out during both the construction and operating phases of the URL. This program involves detailed geological mapping, rock mechanics and hydrogeology studies, and geophysical surveying, to characterize the rock mass surrounding the shaft, and it has been described by Simmons et al. (1983). As part of the construction-phase program, ground-penetrating radar (GPR) surveys are being carried out during excavation, in an attempt to delineate fractures both ahead of the excavation and behind the walls of the excavation. This paper presents the results of surveys performed during shaft excavation and describes a procedure for plotting the data.Ulricksen (1982) cites examples of radar surveys to evaluate surficial deposits, such as peat, sands and gravels, and cavity detection in subsurface hard rock. Fowler (1981) used radar for fracture and clay vein detection in coal seams.In Canada, pioneering work in GPR has been done by Annan and Davis since the mid-seventies (Annan and Davies, 1976). Their work concentrated on problems relating to permafrost in the Arctic ."

Jan 1, 1986

By Yve Fourmanoit

"This paper discusses the exploitation of shallow underground deposits in a very altered geological environment. The methods, their adaptation to local conditions, their evolution, dilution control and recovery of mineral reserves will all be dealt with.The recovery of the B zone crown pillar under 40 m of till that was originally saturated with water, is of particular interest.Future underground development and production start-up of the A-2 zone, organization of mining operations, mechanical services, group incentives and safety practices will also be given.IntroductionThe underground deposit of B zone is not very deep. A 300 m shaft provides access to the mine. In addition , exploitation sublevels are developed every 20 m and are linked by a service ramp. The overburden located on top of the deposit is 40 m thick and is composed of a very dense till.A detailed work plan was initiated to permit mining under the overburden. To do so, it was imperative that efficient methods be developed. At a time when an accident at the Belmoral Mine shook the mining world , it was a task to convince provincial authorities that it was safe.While B zone was being mined , development began in the A-2 zone deposit which has recently been put into production (Figs. 1 and 2).The intention of this paper is to provide an outline of the mining method s and their particular aspects. To do so, some of the mine services are described and a brief outline of the under ground department is provided."

Jan 1, 1990

By P Davidson

For many years, in numerous settings, the need for a language-fair and culture-fair assessment test has been identified as a significant issue for employment and selection for training of remote indigenous community members. Pivotal to the successful implementation and application of such a test is for it to gain the acceptance and trust of the local indigenous communities as a fair assessment and for it to provide organisations with an accurate predictive tool. However, when western tests have been used with indigenous groups, inherent language and cultural bias have had a significant negative impact in terms of community acceptance. These have also affected the accuracy of performance predictability. The Queensland Test was developed to overcome these problems. Originally developed for use in Papua New Guinea, it reduced training failures by 20 per cent. Later refinements were made and it was used with Aboriginal Australians. Since 2002, assessment tests have been used by the Freeport mine in West Papua to support their recruitment, selection and training processes for the local indigenous community, the Seven Suku Tribes. The initial process included the application of standard æwesternÆ assessment tests, which did not provide valid selection predictions, with community members and elders describing these tests as unfair and the organisation being concerned that the results were not accurate. A trial of the Queensland Test was conducted and a high correlation was established between the performance of FreeportÆs current Seven Suku employees as assessed by their managers and their Queensland Test results. Based on the results of this pilot the Queensland Test was successfully implemented as the primary selection tool for potential employees from these local indigenous groups. The testing materials and method gained community trust and support, with tribal elders describing the Queensland Test as a fair and suitable selection tool for their community members. Such results have sparked an interest within the Australian Mining industry, with similar results being reported from a recent trial. The Queensland Test has been implemented at a major site in Queensland and is being investigated for use elsewhere.

Jan 1, 2006

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940

By Alden B. Greninger, Alexander R. Troiano

Metallurgists have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies,30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel. I. The Martensite Transformation Previous Work Microstructure and Crystal Structure of Martensite.—Among the best series of published photomicrographs of quenched steels are those of Whitely,1 Robertson,2 Hanemann and Schrader,3 and Lucas.4 The crystal structure of martensite is body-centered tetragonal, with axial ratio varying from 1 near 0.0 per cent carbon to 1.08 for 1.75 per cent

Jan 1, 1940