Search Documents

By Chengliang Jliang, B. K. Parek, Xuxin Shao

Of the impurities present in phosphate ore, dolomite is the most difficult to remove due to the similar chemical compositions of the impurities and also adsorption of dissolved species of dolomite onto phosphate. A new amphoteric surfactant was found to be a suitable collector for separation of dolomite from phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite in wide pH ranges. The flotation study of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector, but were detrimental to the flotation separation using sodium oleate as collector. A phosphate concentrate with 35.2% P2O5 with 90% recovery was obtained using 290 g/t of the amphoteric collector from a mixture of francolite and dolomite containing 26.2% P2O5. The rejection of MgO was 81.41%.

Jan 1, 1999

This paper describes the planning mechanism and implementation of a progressive rehabilitation programme at Hunter Valley Mine in the Upper Hunter Valley of New South Wales. Hunter Valley Mine is a large open cut coal mine which produces approximately 7.0 million tonnes of coal (run of mine) annually for export. This production level involves the movement of some 60 million tonnes of waste and coal each year.The rehabilitation programme at Hunter Valley Mine has been developed to provide a combination of pasture, based on improved pasture species and timber belts to enhance the visual characteristics of the rehabilitated landform, whilst creating amenity in the form of shade for livestock.The operational philosophy for the rehabilitation programme is that of progressive rehabilitation. The best time to undertake rehabilitation is now.' As a result, planning for the rehabilitation programme is continuous, so that all site works are completed in time for vegetation establishment during the critical periods each year.

Jan 1, 1992

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

By L. Landryova

The Department of Control Systems and Instrumentation, VSB - the Technical University Ostrava, has been involved in a project dealing with utilization of landfill gases, when the methane gas utilization and minimization of its release into the atmosphere was the main concern. The landfill site is generally a place, where technology for energy production can be built. The conditions for this technology implementation vary and depend on various factors. This paper is presenting findings and experience gained regarding a method of methane gas utilization for energy production. This method is concerning building bioreactors at the landfill sites, which are already operated. Every bioreactor can be thought of as a process, which is controlled in order to maximize energy production and minimize the methane gas escape into the atmosphere. The bioreactor landfill can represent a number of environmental and cost savings and, at the same time, is able to comply with all legislative issues.

Jan 1, 2005

The long-term goal of the Collaborative Research Centre 525 is the identification of options for the resource-sensitive supply and utilization of metallic raw materials. In order to address these issues, an integrated resource management system for metallic raw materials was developed and tested. Simulations were carried out, using the tools and methodical approaches developed in this system, in order to compare alternative operating scenarios for aluminium and copper. However, before these alternative operating scenarios could be formulated and assessed, it was necessary to develop a consistent set of indicators to monitor progress towards sustainable development in the processing and utilization of metallic raw materials. The primary objective of the centre is to develop a set of indicators, which adopt a holistic approach to resource management, thereby enabling the assessment of different operating scenarios within the broadest possible context. The target audience for this research consists of decision-makers in the realms of politics, business and industry, as well as NGO?s.

Jan 1, 2003

One of the most unusual assignments in the his¬tory of Loffland Bros. Co. is now in progress with the drilling of a 72-in. diam. shaft in Nevada for the United States Atomic Energy Commission. Projected depth being 3200 ft, by volume, this is the same as a 216,672-ft hole 83/4 in. in diam. Every aspect of the operation is king-sized. The 15,000-lb bit moves into position over the well on a specially-made railroad car riding on rails 14 ft apart. The single drill collar weighs 300,000 lb, is 60 in. in diam., and 43 ft long. The drill pipe is 133/s-in. 72-in. N-80 casing fabricated with special tool joints. The bit chews up 1.05 cu yd of rock for every ft of penetration (This is equal to the volume of 67.71 ft of 83/4-in. hole.

Jan 9, 1964

By M. Prasad, G. M. Rao, A. K. Majumder, T. C. Rao

Froth flotation was employed to beneficiate a lean-grade siliceous rock-phosphate ore containing fluorapatite, the phosphate-bearing mineral. The main gangue minerals were quartz, iron oxides and aluminum oxides. After the rougher stage, four cleaning stages were required to upgrade the ore. The liberation size of the phosphate mineral was below 200 mesh, The reagent scheme consisted of commercial-grade sodium silicate and sodium oleate. The effect of reagent dosages, number of cleaning stages and pulp density on the efficiences of separation were studied systematically. A flowsheet was proposed for the processing of low-grade siliceous phosphate ore containing 12.1% P2O5, 55.36% SiO2 and 15.45% CaO. The flowsheet provided a useable phosphate concentrate containing 34.18% P2O5 and 14.20% SiO2 with a P2O5 recovery of 70.4% (the weight yield was 25.0%).

Jan 1, 1999

Lieut. Louis J. Brunel, now in France, was commissioned on July 27, 1917, as Second Lieutenant in the Engineers Reserve Corps, assigned to the 7th U. S. Engineers, Dec. 10, 1917, and has been with the American E. F. since Mar. 26, 1918. He was assigned to the staff of the General commanding the 5th Field Artillery Brigade, as Engineer Officer, on Aug. 6, 1918. E. Ross Housholder writes that "the record for pontoon bridge building was broken Sept. 25, 1918, by Section A, Co. 4, 5th Engineer Officers' Training School, at Camp Humphreys, Va., of which I am a member. The time was 15 min. 11 3/5 seconds. We then proceeded to break the record for dismantling in 9 min. 57 1/5 seconds. The length of the bridge section was 200 ft. The post band was sent out to meet us, and we feel proud of this record. I have met quite a few A. I. M. E.

Jan 11, 1918

By J. A. Voigt

In an effort to determine the optimum conditions for preparing high purity, fine particle size high temperature superconducting oxide powder, we have investigated how calcination conditions influence the conversion of a chemically prepared hydroxycarbonate precursor powder to YBa2Cu307. We find that the precursor can be converted to phase pure YBa2Cu307 in either oxygen or synthetic air (20% 02. 80% N2) at 850°C. This temperature is substantially lower than the temperature (>900°C) normally used for the calcination of mixed-oxide powders. The lower calcination temperature prevents particle sintering and maintains the desired fine particle size. Powder processed in synthetic air shows a low degree of crystallinity indicating it may be more sinterable than the highly crystalline powders produced when an oxygen atmosphere is used. Intimate contact between powder particle surfaces and a flowing gas atmosphere promotes the reaction between the BaCO3 component of the precursor powder and the Y and Cu constituents.

Jan 1, 1989

By Clay McNail, Paul N. Worsey, John Schillie

"This paper is the result of undergraduate student research over the period of 2 semesters at UMR, which was focussed on developing a practical way to pneumatically stem horizontal boreholes, mostcommonly used underground. The majority of dry horizontal underground boreholes are pneumatically loaded with bulk ANFO. ANFO is preferred due to its low cost and the ease of pneumatic loading. However, stemming underground in the United States is a rare practice. In sharp contrast, stemming material (crushed stone or drill cuttings) is virtually always used in surface holes. The purpose of stemming is to increase blast efficiency by containing the explosive energy in the ground and to reduce environmental effects such as air-blast. The problem with stemming horizontal boreholes are; gravity cannot be used to load stemming material and the ANFO does not have a good interface due to problems with withdrawing the hose and the loading itself. This work follows on from Wilkins’ work on stemming angled boreholes."

Jan 1, 1999

All sections of our community are becoming increasingly aware of the dangers of uncontroll- ed erosion associated with modern earthworksy whether they be concerned with the protection of capital structures, reforestation of mine tailings or generally the aesthetic and ecol- ogical impact. Because of the many ecological variances and climatic conditions no single technique may be offered as the complete answer. Rather that a combination of a series of techniques is nec- essary to achieve an individual end result. These techniques may appear to be expensive initially, but when considered in relation to the overall cost, and we realise that this work represents our only insurance of the stability of our project, the cost of stabilisation is insignificant. Once erosion has commenced the cost of stabilisation escalates dramatically which highlights the definite need to include the requirement of stabilisation in early design of your projects. Stabilisation should commence during construction to ensure that control of mobile soils is gained at the earliest possible time.

Jan 1, 1976

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a short computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By J. de Visser, J. A. Davis

Since the mid 1970's, development of zinc electrowinning (EW) facilities has out-paced its counterparts in the copper and nickel electrowinning industries in the design of efficient, compact, and automated production plants. Recent advances in process automation have provided opportunities to increase current efficiency, productivity and cathode quality, while reducing the footprint of the plant and the number of operating personnel working on top of the cells. Usually, the practice has been to allow a totally contaminated building structure, combining the plant ventilation system with the process cooling air. As a result, facilities employing this practice are finding difficult to meet their process design criteria and the stringent labor and environmental requirements. This paper provides an overview of the problems and disadvantages associated with these older process designs. It also describes new developments in ventilation systems, particularly building design developments and cost savings that are possible when improved ventilation systems are introduced into efficient process operations. Lead-

Jan 1, 2000

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002

Studies of the morphology of seamounts within the Hawaiian, Line Islands, Gilbert and Phoenix Seamount groups indicate that the morphology and size distribution of seamounts vary significantly from one seamount group to another. The Line Islands group appears to be the most complicated of all the groups studied thus far. This group is complicated by reactivation of volcanism, which has superimposed volcanics on sedimentary rocks. These seamounts display abundant volcanic features on their summits. Seamounts within the Hawaiian seamount chain display a marked absence of volcanic features due to the . presence of thick carbonate caps. Reef platforms and sealevel benches are very common on these seamounts but are absent from seamounts in most other seamount chains in the central Pacific. Slope angles vary regionally between seamount groups. The minimum slopes are found on Necker Ridge in the central Pacific basin. The maximum slopes are found on ridge-crest seamounts. Roughness increases proportionally with mean slope angle.

Jan 1, 1987

By J. A. Eisele, D. J. Bauer, L. E. Schultze

Approximately 100 million mt of magnetic reject tailings, which contain apatite and about 1% yttrium and rare-earth elements, exist in the eastern U.S. as a result of iron ore mining operations. At the present time, no economic process is available for recovering yttrium from this material. The U.S. Bureau of Mines (USBM) studied the problem to determine if an effective low-cost method could be found, thereby increasing our domestic yttrium reserves. [Fig. 1] is a line drawing of a photograph taken during microprobe analysis of a sample of the tailings, and shows the distribution of yttrium. Typical analysis of this material is 0.14% yttrium and 1.1% rare-earth elements (mainly lanthanum through neodymium). Over half of the yttrium is present as a hydrated Ca-Y silicate deposited along interfaces in the grain structure; whereas, the remainder of the rare-earth elements occur as Ca-Fe-RE silicates. The remaining yttrium and rare-earth elements are in solid solution with the

Jan 1, 1977

By Edward R. Torak

The Ohio Coal Testing and Development Research Facility (OCTAD) was commissioned in 1992 by the Ohio Coal Development Office and the Ohio Power Company to support evolving process technologies that will lead to increased environ- mentally sound use of coal. OCTAD is equipped with advanced physical concentration devices and processes capable of beneficiating coal to levels beyond conventional practice. The first task of OCTAD operators was to test the cleanability of the Meigs Creek Seam Coal in advanced circuitry and compare the results to conventional cleaning levels. In testing the seams, OCTAD circuitry was configured to produce middlings on the coarse and intermediate size fractions. These middlings were subsequently crushed to a finer size (28M x 0) and subjected to cleaning in fine heavy-media cyclones and advanced froth flotation circuitry. Nearly thirty-six full-scale production runs at various operating conditions were completed during the campaign. The results of the test program are examined in this paper.

Jan 1, 1995

By E. F. Divers

Adequate ventilation of coal mine working faces is the most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. US Bureau of Mines research has shown that to control respirable dust, you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane, the most effective approach has been to use a blowing brattice, or tubing, and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present. Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan- powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray- fan controls methane on exhaust-ventilated sections.

Jan 1, 1987

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000