Search Documents

Mills Day left a journal of his travel to Ohio and return by way of Pittsburgh in 1810. He left this comment about western Pennsylvania: "June 19. As I proceeded toward Pittsburg, (From Washington and Canonsburg) the country grew more populous. The hills appeared to consist of strata of freestone, iron, coal, and slate. June 20. Its (Pittsburg's) water communication with a vast extent of country and the immense beds of coal in its immediate vicinity render it a place peculiarly adapted to manufactures. Coal may be obtained of a good quality, ready delivered at 5 cents a bushel."1 Until within a year or so of this period, coal was used for domestic purposes, brick-making, by blacksmiths, etc.; now the industry entered a period of rapid growth caused by the introduction of the steam engine. As manufacturing was increasing due to the settlement of the western country, the additional facilities created by mechanical power were welcome. Apparently the first engine was installed in Pittsburgh, in a steam grist mill, in 1808; it is described in the Navigator of 1811: "The water of the boilers are heated by large fires made of stone coal, which is introduced at one end into a grated fire place as long as the cylinders themselves; the quantity of coal consumed daily by these boilers is said to be about twenty bushels, which cost one dollar." Later it mentions the effect of burning coal:

Jan 1, 1942

By W. Luyken, E. Bierbrauer

A number of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing. These publications demonstrate both the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. Graphical Analysis of Ore-dressing Processes The following is from Truscott's Text Book of Ore Dressing (London, 1923): x = assay of ore treated (feed). y = assay value of the concentrate. 2 = assay value of the tailing. a = weight of feed. 6 = weight of concentrate. c = weight of tailing. C = fractional concentration = = . a y - z K = ratio of concentration = 1/c a/b = y-z/x-z 2 B = fractional recovery = 9 = C y/x (3) 100R = percentage recovery. Copt. = theoretically best concentration. 100 — Copt = waste in the feed.

Jan 1, 1930

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

By A. J. Neale, B. C. Flintoff

"A review of the dynamic rod mill-ball mill grinding circuit simulator developed at the University of Alberta, highlighting the modular structure and open-ended design, demonstrates the ease with which classical feedback control strategies can be designed and implemented. Various open loop simulations are presented to demonstrate the highly interactive nature of the grinding circuit and to indicate where potential control problems may be encountered. Closed loop simulations are examined, beginning with the basic SISO classical feedback control of circuit product size. Further improvement in the grinding circuit performance in the presence of various disturbances is realized through the application of a classical MIMO feedback controller. As an example of advanced (multivariable) control, static decoupling is implemented and shown to provide additional improvement in overall circuit performance.INTRODUCTIONIt has long been recognized in the processing industries that a dynamic process simulator is an indispensable tool in the design and evaluation of automatic control schemes. In mineral processing the lack of these simulators is felt to have been a major hindrance to the widespread implementation of effective process control systems. In particular dynamic simulation is a necessary precursor to any study of modern (as opposed to classical) process control methods. This paper discusses the development of a dynamic simulator that can be used to study various feedback control strategies. The simulation software provides a powerful educational tool for those individuals interested in grinding circuit control."

Jan 1, 1988

By Richard W. Markley

The predominant methods for mining coal in the USA are room and pillar and longwall. Approximately 95 percent of the coal is mined by room and pillar and 5 percent by longwall. The U.S. Department of Energy (DOE) has an ongoing program to improve the rate, quality, and cost effectiveness of stabilizing the roof for both of these mining systems. In room and pillar mining, the installation of permanent roof support is often the task which paces the system operation, and it thus controls the level of production achieved during any mining shift. Two automatic roof bolt insertion equipment developments are discussed, as well as a flexible drill for operation in thinner seams. Progress will be reported on under- ground trials of a particular flexible drill which has been combined with a bolt inserter to form a compact, reliable module for retrofitting to continuous mining machines. In longwall mining, the use of hydraulic supports on the working face provides roof stability. The DOE has several trials ongoing with shield- type supports in difficult strata conditions which are described, as well as a co-funded project with the Bureau of Mines on a resin injection remedial method for consolidating a shear zone at one site. A project to improve the match of strata conditions to shield design is also described, which involves the use of a 1360 tonne vertical load mine roof simulator.

Jan 1, 1983

By H. F. Yancey

PHYSICAL properties have been used for a long time in characterizing different kinds of coal, and physical properties, such as friability and slacking, have been included with chemical properties in grouping coals according to the widely used system of classification adopted by the U. S. Geological Survey. Nevertheless, the usefulness of physical properties for classifying the different ranks or kinds of coal has been limited because it has not been possible to express these properties in definite form as numerical values. Because of the present wide interest in the formulation and adoption of a satisfactory system of coal classification, the Northwest Experiment Station of the U. S. Bureau of Mines, in cooperation with the College of Mines of the University of Washington, has recently completed a study of the physical and chemical properties of approximately 100 different coals ranging from lignite to, anthracite. PURPOSE AND SCOPE For this investigation samples were collected in approximately 45 mines and prospects in Washington and 23 mines in other states. The following studies, in addition to proximate and ultimate analyses, were made of the samples: Determination of (1) friability, (2) slacking or weathering characteristics, (3) yield of products by low-temperature carbonization in a laboratory retort, and (4) agglutinating value. Most of the coals examined were subjected to each of the tests enumerated, but with coal of some ranks this was unnecessary in some instances, and in others it was not feasible to do the work involved.

Jan 1, 1932

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

By Adeloju S, McQuade CV, Riley SJ

Metal contamination of sediments can be an issue for minesites discharging water. Water sampling of receiving waters is frequently undertaken. Sampling and analysis of sediment is less common. The variability of receiving environments makes the formulation of a generic sediment sampling strategy virtually impossible. Each situation needs to be carefully assessed before sampling is undertaken. This paper outlines the approach taken for one such survey.The main factors that need to be considered in a survey of surficial sediments are sample representativeness and sample variability. A simple data set from one site within a regional survey is used to illustrate the importance of these factors. The metal content of sediment is shown to vary significantly over small spatial scales.The variability associated with the spatial distribution of samples within a site is shown to be the most significant source of variability in the study. This variability could bias the results of a study if not planned for in the sampling methodology. Taking multiple samples from within each site (sub-site samples) and combining the data gives a more representative indicator of overall conditions than a single sample. The optimum number of sub-site samples to be taken from each sampling site was found to be 15.It is shown that a composite of sub-site samples can give a good indication of the average site metal content, while considerably reducing the sample preparation and analysis effort.

Jan 1, 1998

By Bruce K. Hebblewhit

Australia is well endowed with extensive reserves of thick underground coal scams, particularly in the range of 4.5m to 9m thicknesses. (For the purposes of this paper, thick scams are defined as being greater than 4.5m thick.) At the present time, the thickest, high production, high productivity underground mining operation in Australia operates at a maximum of approximately 4.8m using single pass longwall methods. In a number of instances, conventional' height operations are mining thick seam coal, effectively sterilising considerable reserves - either because of financial or technical risk concerns, or in some cases poorer quality coal at some horizons in the scam, UNSW has been involved in thick scam mining research over many years, most recently through an ACARP -funded project, jointly with the CMTE in Australia. A key part of that project involved the assessment of the relative geotechnical risks associated with the various methods under consideration. The methods were: single pass longwall; multi-slice descending longwall; soutirage and related caving methods (including the Chinese Longwall Top Coal Caving method (LTCC)): and hydraulic mining. A formal risk assessment process was adopted to review the risks, relative to a conventional 4m high longwall operation. This paper presents the findings of that risk review and discusses the geotechnical issues (and some possible solutions for risk management) which need to be dealt with in order to bring these methods to fruition in the context of the Australian coal industry environment.

Jan 1, 2001

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By Axel Preusse

In the Ruhr district, pipelines of public and private infrastructure are made of cast iron, steel, plastics or asbestos cement. Legal framework, technical regulations and normative standards define which pipeline materials may be used for the transmission of which kind of product Thus ground water endangering substances as well as inflammable or explosive products are only permitted to be transported in steel-made pipelines. Ground movements, due to underground mining, are transmitted via the soil to the pipeline and cause extra strain within the steel pipeline (Figure I). In extreme cases durable deformations may occur, characterized by an oval profile or a fold in the pipeline. To avoid or minimize damages, balancing elements are installed into the concerning pipeline, reducing the ground movements which might otherwise cause damages. [ ] The distance between the balancing elements is not arranged by random, but by a calculation method developed in a doctoral thesis [Spielberg, 1999] which represents the actual available standards in science and technology. The calculation method considers all relevant influencing variables with impacts on the movement behaviour of steel pipelines in mining areas, such as technical data of pipeline design (e.g. steel grade, wall thickness, weld seam quality), soil conditions (e.g. friction), laying depths of the pipelines, the operational impacts (working pressure, corrosion) and the mining impacts. As of today, mining has caused no damages to steel pipelines protected by this calculation method.

Jan 1, 2004

By V K. Singh, G Sural

The problem of spontaneous heating/fire is very common in coal mines all over the world. The coal industry faces many problems day by day due to the occurrence of spontaneous heating in the open pit coal mines. Presently, about 70 per cent of total coal production in Indian mines is being carried out by open pit mining. Fire in coal, particularly in open pit mines not only causes irreparable loss of natural wealth but also damages the surface structures and pollutes the environment. It is well known that 75 per cent of the fires occur due to the spontaneous combustion of coal. Spontaneous heating is a very common occurrence in coal mines and is a major factor contributing to mine fire. The liability of coal to spontaneous heating causes many serious problems before, during and after mining. In opencast mines, coal immediately oxidises and catches fire due to the intrinsic characteristics of coal, such as low rank, high moisture, high volatile matter, presence of sulfur in the form of pyrites, low crossing point temperature (CPT) and ignition point temperature (IPT) value and less incubation period. In opencast mines, when the coal benches are left idle for a longer time, heat accumulation takes place in favourable conditions and sometimes leads to fire. The purpose of this paper is to present the different successful case studies regarding the safety management of open pit coal mines from occurrences of spontaneous heating/fire.

Jan 1, 2007

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division's energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee's responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By J. W. Rutter, K. T. Aust

The motion of individual grain boundaries under a constant driving force was investi,qated for zone-refined lead, with and without solute tin additions. The rate of boundary migration was found to depend strongly on tin content and on the orientation relationship between the adjacent grains. The results are compared with the theory of impurity-controlled grain boundary miqration developed by Lucke and Detert. Evidence was found that grain boundaries separating grains which have the Kronberg-U&apos;ilson orientation relationships of 38 and 22 deg about <Ill> and 28 deg about <100>, correspond to boundaries of high mobility. The results are discussed in relation to the formation of annealing textures in metals and the structure of high-angle boundaries. It is generally known that small amounts of impurities in solid solution greatly influence the re-crystallization behavior of metals. For example, the addition of 0.005 at. pct of tellurium to copper,&apos; or 0.005 at. pct of silver to lead,2or 0.01 at. pct of manganese or nickel to aluminum3 greatly decreases the rate of recrystallization of these metals. However, this effect may be the combined result of a decrease in the rates of both nucleation and growth; recrystallization experiments do not separate these two factors. Bolling and winegard4 determined the effects of small quantities of tin, silver, and gold on grain growth in polycrystalline zone-refined lead.

Jan 1, 1960

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines&apos; (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By J. H. Schuenemeyer

Consider a set of points, some of which are anomalous (larger than a specified cutoff value), located on a plane. Whether some or all of these points are clustered to form one anomaly or more or, alternatively whether these points are scattered at random, may be investigated by measuring perimeters of convex hulls. A convex hull is the smallest convex polygon that will encompass a group of points. (Examples of convex polygons are triangles, rectangles, and all other regular polygons.) A set of anomalous points is selected and the perimeters of the convex hulls of this set and all its subsets are measured and compared with tabulated values of perimeters for each subset size. For a given subset size consider those perimeters which are less than the tabulated perimeter. If the number of convex hulls is greater than the maximum number expected by chance, then the chance that any one of the observed-hulls-is a nonrandom cluster is the ratio of the observed number to the sum of the observed and the maximum number expected by chance. Otherwise, the points are evidently not clustered. If many sample points are anomalous, an alternate model defines various configurations of contiguous points and compares the observed number of configurations per unit area with the expected number. Applications are discussed in several fields of geology and geochemistry-including geochemical exploration surveys and heavy mineral spatial distributions--as well as in mining (dust control) and medical geography.

Jan 1, 1972