Search Documents

By S. Naidu, J. Kelley, Roger Amato

The Alaskan Continental Shelf covers 76 % of the total shelf area of the United States. There are a lot of potential gravel deposits in the Alaskan offshore region. The gravel resources are currently not feasible for mining for the following reasons (U.S Congress, 1987): 1. Much of the glacial gravel is poorly sorted. 2. Gravel deposits are overlain by sandy and muddy layers. With the sea level expected to rise 70 cm in the next 100 years (Intergovernmental Panel on Climate Change, IPCC, 2001; Day, 2004), erosion of coastlines will be a major problem not only in Alaska but worldwide. Hence beach nourishment projects designed to minimize erosion will require large volumes of sand and gravel. Offshore areas will become a logical source for the fill material because of their proximity and ready availability. It is likely that future supply of coarse aggregate in Alaska may involve exploitation of marine deposits. The Chukchi Sea is a potentially favorable region for this type of mining because of extensive deposits of paleo beach and other relict gravel found in the near shore region (Stauffer, 1987). However a systematic analysis of potential gravel resource has not yet been conducted and it is the purpose of this research to estimate the size, extent and variability of gravel material that may be available in the continental shelf, offshore Kivalina.

By Hiromu Kusakawa, Tetsuo Kanematsu

INTRODUCTION In urbanized area with heavy street traffic and with environmental requirements to lessen construction noise and vibration, the cut-and-cover is not always a feasible method to build a small diameter tunnel for sewage, water or other utilities. That is where the use of the shield machine to bore such a small diameter tunnel should be considered as a more acceptable alternative. Although the shield machine of this type should be small enough to meet specific requirements for a given tunnel, it should be big enough to provide some working space inside of the tunnel. Recently, we have successfully developed the fully mechanized small diameter tunneling method which enables us to bore a tunnel as small as 600mm in finished diameter. This paper discusses the concept of this newly developed method, including a case history where sewage tunnels of 800mm finished diameter were constructed by using this method. OUTLINE OF METHOD Developed from the original slurry shield pipe-jacking tunneling method, this method is highly automated so that all operations inside of the tunnel can be remotely controlled. Various data including the advance rate, position and inclination of the shield are transmitted to the central control room outside of the tunnel and monitored by the CCTV and the instrument panel at all times to

Jan 1, 1981

By Bruce Congleton

The Florida phosphate industry is a leader in environmental control, both in terms of dollars spent and significant achievements. For instance, since 1960 the phosphate industry has spent over $71 million for air pollution and control devices, including installation, research and development and maintenance. Water pollution control expenditures also total in the millions, with over $69 million spent in the same 10 year period. The industry also is a leader in water conservation measures, having spent nearly $ 18 million since 1966 for conservation devices. Since phosphate is mined by strip mining, land reclamation plays an important part in the environmental control picture. Here again, the phosphate industry has met the challenge with a voluntary program of reclamation which accounts for over 20,000 acres of land useable after mining has taken place. In terms of progress in environmental control, the industry has been able over the years to solve within the limits of technology the fluoride emission problems it once had, and is currently at work solving sulfur dioxide and particulate problems. In just the past year the industry also has been extremely successful in limiting phosphorus and nitrogen discharges into area streams. The industry continues to cooperate with state and local pollution control officials on matters of environmental control, and future plans include even closer cooperation and assistance, as well as increased expenditures.

Jan 1, 1972

By D. Koch

Bentonites and bentonite containing sealing materials are used since many years for sealing purposes in foundation, dike construction, hydraulic engineering and landfill construction, especially for encapsulation of old waste deposits In the near future compacted bentonites will be important components of multi-barrier systems for dry charge of old mines, for underground disposal of hazardous or radioactive wastes. Because of their exceptional physical, structural and chemical properties, bentonites are offering manifold possibilities to protect the environment against the negative effects of dumping grounds. Often the compliance with legal regulations for waste dumping or the isolation of contaminated areas is possible only by using bentonite containing sealing systems. The essential properties of bentonite, bentonite containing building materials and the different techniques of making horizontal technical base liners and vertical cut-off walls are explained. For horizontal technical base liners the adsorption ability, the ion exchange capacity and the swelling behavior of bentonites are important. For cut-off walls bentonite controls the rheological behavior of the slurry and is responsible for the low permeability of the hardened bentonite-cement-wall. In the multi-barrier systems of repositories for chemical or radioactive wastes compacted bentonites are considered to be favourable sealing and backfilling materials because of their high swelling capacity, their adsorption and ion-exchange ability and their plasticity in water saturated state.

Jan 1, 2005

By R. K. Datta, T. S. Davis

YVO4:EU, excited under 3650A radiation, shows a marked increase in total brightness with in~rease in temperature. At 25°C the response to 3650A radiation is about 48 pct of its maximum response which occurs at about 350°C, Fig. 1. In an attempt to explain the phenomenon, one of the present authors' (R.K.D.) investigated the diffuse reflectance spectra of the phosphor at different temperatures (up to -150°C) and was unable to observe any significant change to which the increased brightness could be reasonably ascribed. Since then diffuse reflectance spectra at elevated temperatures have been obtained in this laboratory using an improved device. A significant decrease in the diffuse reflectance of a phosphor in the ultraviolet region—especially in the longer wavelength region—at -300°C has been observed. The purpose of this note is to describe the device used for high-temperature reflectance measurements and to explain the increased brightness of YVO4:Eu phosphor at elevated temperatures under 3650A excitation. Experimental. YVO4 and YVO4:Eu samples were prepared as previously described.' The elevated-temperature reflectance spectra were obtained with a Cary 14 spectrophotometer equipped with a diffuse reflectance accessory and a ring collector. CaF2 was used as the standard. The cell used

Jan 1, 1969

By Arthur A. Center

World production of electrolytic zinc has shown an increase for each year since 1932. Production up to 1936 was summarized in my earlier paper [Trans. A.I.M.E. (1936) 121, 453-4641, and this present paper carries the subject through 1943. During this time of increase, it is safe to say that the average purity has been raised more or less continuously, and the amount of four-nines metal has been in- creased. While the period reflects preparations for and the carrying on of the present war, electrolytic zinc proved its value in many industries as a peacetime metal in the years from 1919 to 1940. World production (Table I) increased from about 594,000 tons in 1936 to around 858,000 tons in 1943; United States production increased from 127,171 tons to 329,903 tons for the same years. Total production of primary zinc in the United States is given in the first column of Table I; retort production of primary zinc, obtained by difference, in the last column. The curves drawn from these figures are shown in Fig. I. They represent continuations of the curves in the earlier paper that cover commercial production of electrolytic zinc from its inception in 1915 to 1935. The earlier paper gave data for total world production and foreign retort production (calculated therefrom) and showed curves of electrolytic vs. retort production

Jan 1, 1944

By Franklin Bache

There seems to be in the public mind, and even in the minds of some coal-operators not experienced in mines subject to dust-explosions, a feeling that there has been somet-hing mysterious at the bottom of a number of recent American colliery-exploaions. It has been declared in cases of accidents in mines regarded as particularly well equipped, in which every preventive precaution was said to have been taken, that the explosions were incomprehensible, and resulted from causes beyond the present knowledge of the practical coal-operator. But it is safe to say that no explosion has taken place which could not be explained by reasons well understood by most operators. The U. S. Geological Survey Testing Laboratory, recently inaugurated at Pittsburg for the reported purpose of investigating scientifically the matter of explosions in mines, will discover no new explanation of explosions. It can, however, co-ordinate the previous investigations of similar boards in England and on the Continent; and it may do a vast amount of good by promulgating widely, and in a form comprehensible to the most unlettered miner, certain facts and obvious deductions that cannot but have an effect in reducing the number and extent of the mine-disasters which, in the last few years, have been so terrible in frequency and magnitude.

Jan 1, 1910

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By Jean-François Bougard

It has already been said and written many times that the construction of tunnels in urban areas has proved more and more indispensable, if not vital. The subsequent development of tunnelling for 15 or 20 years has brought large and sometimes spectacular improvements in the fiel of execution methods. But, particularly in urban areas, the difficulties to be overcome have been and still remain very important. As a matter of fact, most of big cities, have been settled near rivers or lakes; therefore the geological nature of the subsoil is soft ground and the level of ground water is high. As a consequence, tunnelling is often faced with many well-known difficulties and dangers issued from decompression or loosening of the ground, sometimes accompanied by a lowering of the water table. This may compromise the safety of the excavation itself and of the workers, and also cause settlements which many severely damage nearby buildings or structures. This is the reason why it is always necessary to work out specially adapted methods and even to develop new ones. In most cases, each work is a particular one and has to be specifically studied since numerous data are to be taken into account, related not only to geology, cohesion and behaviour of the different layers concerned, ground water, the activity of it, but also to

Jan 1, 1979

In the sixteenth century the Spanish Captain da Alvaro Soavedaro, on a search for the explorer Ferdinand Magellan, came across the main island of New Guinea which he named Isla del Oro (Island of Gold). Since that time exploration for, and mining of, gold has been pursued by many, culminating in . the development of major world-class projects in the latter part of the 20th century. Though various prospectors have panned for gold and small gold mining projects were undertaken through the seventeenth and eighteenth centuries, it was not until the 1880's when mining became a more concerted economic venture. Misima and Woodlark Islands in Milne Bay, Gura-Ackera and Yoada in Oro, and Lakekamu in Gulf Province and Keveri in Central Province were all gold producers by late nineteenth century. It was in the 1920's that corporations began mining in PNG and with the commencement of production at Panguna in Bougainville in 1972 a new era of mega-project mining began.' Today there are two large mining projects producing mainly gold and copper. The first, already mentioned, is Panguna on Bougainville Island. This project has provided Government with $US 475 million in taxes. ok Tedi is the second large mine development located in Western Province. It began production in 1984 with the extraction of the deposit's "gold Cap".

Jan 1, 1987

By Jan Nemcik

Among other products steel mesh has been used successfully for many years to support strata and minimise loose material from falling into the mine opening. Installation of steel mesh has proven to be difficult to automate and many other products, such as Thin Spray-on Liners (TSL), have been proposed as a replacement. Ideally, the mechanical properties of these products should be superior to those of the steel mesh, however, most TSL trialled in mines to date have been weak and in addition have had slow cure times, as a result none of these materials can seriously compete with steel mesh. Now a new polymer product that cures in seconds and forms a stiff strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong. To enable selection of a suitable polymer material for roadway skin reinforcement several numerical models were constructed to investigate the role of interface roughness and the influence of polymer stiffness on load transfer along the rock-polymer interface. Laboratory tests indicate that the shear adhesion of the rock-polymer interface can be substantial while the tensile adhesion can be much lower. The models indicate that the natural stone roughness and surface waviness plays a major role in shear adhesion while the elastic properties of polymer liner can significantly influence the polymer ability to resist fracture opening.

Oct 1, 2009

By Colin Rae

THE absence of paraffin and other oil hydrocarbons in the soil, although they are concentrated in extensive deposits in some localities, the common distribution of plant remains through many formations that .are not productive for oil, and many other factors, seem to indicate the existence of an intermediate organic compound between the complex plant compounds and the petroleum hydrocarbons; and much evidence points to the humus acids or associated organic compounds, which are probably collected by surface waters and concentrated in certain areas by means of precipitation by electrolytes, which would be contained in sea water or possibly in various inland seas or lakes. PRESENT-DAY EVIDENCE There are many present-day evidences of the association of petroleum with humus acids. Binney, in 1912, made observations without explanations on the peat mosses of Down Holland, England, where he found petroleum being formed by decomposition, in the presence of an infiltration of sea water. The analysis of a typical peat will show its relationship to the humus acids under consideration. SAMPLE 'No. 1, SAMPLE NO. 2, PER CENT. PER CENT. Water : 20.0 29.5 Ash 3.0 3.05 Fiber 47.0 54.95 Humus acids 30:0 12.50 J. D. Haseman and others have noted the association of asphalt and hydrocarbons with the swampy, boggy areas, particularly adjacent to the sea.

Jan 2, 1922

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

EDWARD HART*, Easton, Pa. (written discussion?) .-In 1895 I visited the chemical plant of the Messrs. Chance at Oldbury, England, under the guidance of Mr. France, the manager. In the stock house I saw a pile of coal brasses with adhering coal and said to Mr. France, "I should think you would get dark acid." "Yes," he replied, "our acid has always been rather black. and our customers have grown used to it. Some time ago we ran out of brasses and could get only Spanish pyrite. Our product became white and the customers began to complain, so I put a little sugar in each carboy." E. A. HOLBROOK,* Pittsburgh, Pa. (written discussion?).-Mr. Davis says, "A very large tonnage of pyrite is annually being thrown in the waste in the coal mines of this country." This quantity is much larger than is generally realized by people not intimately associated with coal mining. At the beginning of the war this country seemed threatened with a short-age of pyrite. The U. S. Bureau of Mines conducted a general investiga-tion of the pyrite resources of the country in order to ascertain what material was commercially available. The general pyrite investigation was in charge of H. A. Buehler, with the subsection on coal pyrite in charge of E. A. Holbrook.

Jan 10, 1919

A. L. FIELD, Cleveland, Ohio (written discussion*.-)In equation 2, B is used to denote the ratio of bases (lime plus magnesia ) to acids (alumina plus silica) it being stated that this ratio gives more concordant results than the ratio either of bases to silica, or of lime to silica. I find, however, that, by making use of the ratio between true CaO (CaO by analysis minus sulfur calculated to CaS) to acids, equation 2 may he modified to agree with the observed facts within an average error of 0.0041 per cent. sulfur instead of 0.0045 per cent. The revised equation is s = 0.072 + 0.01835 - 0.00061 (t - 1400) - 0.0403B where B is the ratio of true CaO to Al2O3 Plus Si02, and the other symbols have the same significance as before. I would not appear to stress too much this slightly better agreement of the revised equation with the observed sulfur. Yet I believe that the use of this ratio of true CaO to acids is to be preferred, if for no other reason than the fact that it is more in harmony with the previous findings of the Bureau of Mines with regard to the effect of magnesia and other impurities on slag viscosity.1

Jan 12, 1919

By Brock H. Morrison

One of the major criterion of any mechanised tunnelling operation is to minimize downtime of the tunnelling machine by employing the most efficient muck handling system space and economic factors permit. A tunnelling machine which remains idle during a large percentage of the available shift working time is a luxury no contractor can afford. There are several possible reasons for non-productivity of a tunnelling machine ... the inability of the muck handling system to keep pace with the tunnelling machine on a continuous basis is one major cause. In large diameter tunnels, where several trains or more than one muck hauling unit can operate simultaneously, downtime of the tunnelling machine may be kept to an acceptable level. On small to medium diameter tunnels, 8 feet to 14 feet in diameter, the muck removal support system is normally restricted in capacity, resulting in an excessive tunnelling machine downtime as the tunnel extends from the shaft. There is a need for an efficient, continuous and economical muck removal system for small to medium size tunnels being driven by a hard rock machine. This paper is intended to provide an insite into pneumatic conveying, and explain the Radmark System; its development and utilisation in the tunnelling and mining fields. STATE OF THE ART Pneumatic conveying is the transportation of bulk materials

Jan 1, 1997

By J. L. Stokes, L. J. Demer

It has recently been shown' that epitaxial films of silicon carbide deposited on silicon single crystals possess desirable properties for semiconductor applications. There is one apparent disadvantage to such a system, however; since epitaxial deposition is a high-temperature process, it can result in plastic deformation of the silicon substrate. The accompanying Berg-Barrett X-ray diffraction photographs reveal plastic deformation in two silicon semiconductor crystals which occurred when the crystals were coated with an epitaxial layer of silicon carbide at 1150°C. Due to differences in thermal expansion between the silicon substrate and the epitaxial silicon carbide, the silicon was subjected to stresses while still in the plastic temperature range. Both crystals shown were 0.7 in. in diam and 0.0055 in. thick. The crystals were sliced from a larger crystal so that their polar axes were parallel to the [ill] direction. After cutting, the crystals were polished with diamond paste, and etched in HC1 vapor to remove surface damage re- sulting from the cutting and polishing operations. This provided clean, damage-free surfaces on which to deposit the silicon carbide. Figs. l(a) and l(b) are reflection and transmission photographs, respectively, of the same crystal. A smaller portion of the crystal is shown in the transmission geometry, because a vertical slit was

Jan 1, 1965

Subsidence prediction methods can be divided into two basic types: empirical and analytical. Empirical methods are based largely on a combination of experience, intuition and observations from a large number of observed subsidence data. They are simple in their application, but they are not based on any principle of mechanics. Analytical methods are based on equivalent material modelling principles, where the ground surrounding the extraction is mathematically represented by idealised materials that deform according to the principles of continuum mechanics. Wide applicability and improved understanding are the principal advantages claimed for this approach. In NSW, significant progress has been achieved in the area of subsidence prediction during the last ten years. Empirical prediction curves are available in NSW for predicting the ground movement in the Southern and Newcastle Coalfields. A' comparison of subsidence values predicted from these curves with the actual monitored values indicates that the curves are adequate for use in conjunction with the existing damage assessment methods. Future research for improving the existing empirical prediction curves can only be justified if it is cost effective. There are several numerical models currently in use in NSW for predicting subsidence. The models do not appear to be superior in their ability to predict subsidence when compared with the empirical curves. the performance of these models will no doubt improve along with advances in defining strata properties and failure mechanisms.

Jan 1, 1991

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986