Search Documents

By A. G. Rozner

TRANSVERSE rupture tests have been commonly used in mechanical investigations of brittle materials. The specimens are simple, easy to prepare, and loading presents no difficulty. Owing to the complexity of stress distribution in bending1 one can determine stresses rigorously only for the elastic range. The bend-test results, however, are at times converted into tensile-strength data, determined as maximum fiber stress. The assumption is made that for small plastic deformations the linear stress-strain relation applies. This problem was experimentally investigated by Bach3 who tested cast iron in bending and in tension and found that the maximum fiber strength obtained in bending exceeded the experimental tensile strength by a factor depending on the geometry of the tested piece. The factor varied from 1.57 for a rectangular cross section to 2.12 for a circular cross section of the tested beam. Since this work was carried out 60 years ago, the cast iron used could be expected to have been highly brittle, thus the extent of plastic deformation prior to fracture very small. We have therefore carried out a number of tests on magnesium-modified cast iron with an average elongation of -5 pct. It was hoped that the data obtained from the tests would serve as a guideline for comparing data obtained in tension and bending for brittle materials. Mechanical properties were measured at room temperature on an Instron tensile machine at a crosshead speed of 0.05 in. per min. The three-point bend test employed cylindrical bars 0.20 in. in diameter with a 1.0-in. span. For the tensile test, cylindrical tensile specimens with a gage length of 0.85 in. and a diameter of 0.160 in. were used. Results are summarized in Table I. From Table I one can see that fracture strength

Jan 1, 1965

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

Strategic planning in mining is an important value accretive process. One of the most important aspects during the planning phase is determining the correct mine and plant design. The traditional mine site design (mine, plant, stockpiles, dumps) develops a fixed system for one set of conditions or expected values. A robust design is a fixed system that is designed to deal with a large range of conditions without changing the system design. A flexible design changes the system dynamically in response to changes in uncertainties. It is hypothesised that a robust design generates less value than a flexible design as it fails to realise the value of actively managing the operation. One of the most critical aspects in creating strategic value from a project is embedded in the design of the system. A flexible design has components that allow the design of the system to change over time. An operational plan is proposed as a hybrid of a robust and flexible design. This paper seeks to compare these different design methodologies. An analysis of the same case study is undertaken to compare these approaches, showing an a traditional net present value (NPV) of $1678 M, robust design NPV of $1787 M and an operational plan NPV of $1867 M - an increase of $170 M.

Dec 6, 2010

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By H. F. Coward, G. W. Jones

"IntroductionIn the course of an investigation on the influence of black damp (a mix of nitrogen and carbon dioxide) on the limits of inflammability of fire damp (methane) in air, some new information was obtained concerning the factors that determine whether or not a gas mixture is capable of self-propagation of flame. Volume for volume, carbon dioxide exceeds nitrogen in its extinctive action on flame, an effect which is generally attributed to the higher molecular heat capacity of the former. Argon, a as of lesser heat capacity than either, proved to Lave less extinctive notion. If, as seemed likely, the extinctive action of a chemically inert gas could be attributed entirely to its heat capacity, then helium should behave like argon; equal volumes of these two oases should exhibit equal extinctive action, for their molecular heat capacities are nearly identical at laboratory temperatures and, in all probability, remain constant up to and beyond flame temperatures. The experiments reported here show, however, that helium has proved to be more extinctive of methane flames than argon.Method Used in ExperimentsThe limits of inflammability of methane, in various ""atmospheres"" composed of mixture of air with one or other of the diluent were determined in a vertical glass tube, 6 feet long and 2 inches in diameter. The lower end of the tube was opened by sliding away a ground-glass joint and the flame of a small spirit lamp was immediately passed across the aperture. The tube was sufficiently long to enable observers to judge whether a flame was self-propagation for if a mixture were incapable of continued self-propagation pf flame, the lamp of flame formel above the source of ignition was extinguished within feet of its passage up the tube."

Jun 1, 1926

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By L. van Dyk

The project was aimed at evaluating the double-header trains implemented at Great Noligwa mine, looking at the changes from the old conventional trains to the new trains, and identifying possible improvements to obtain an even better and more productive tramming system. The methods used to evaluate the double-header trains at the mine included personal observations, time studies, personal interviews, technical research, safety analysis, cost analysis, production analysis, breakdown analysis, break test analysis, comparisons and working closely with engineering department and manufacturers. Issues that were evaluated are the improvements in safety, cost reductions, tramming congestion reductions, better efficiencies, labour optimization, enhanced driver safety and maintenance. Shortcomings of the double-header trains were identified and recommendations made to improve on the shortcomings. Findings of the evaluation study indicated the following: ?Drastic improvement on safety ?Extreme cost reductions ?Reduction in tramming congestions and bottlenecks ?Better tramming efficiencies ?Optimized labour placement ?Enhanced driver safety ?More effective maintenance. Although there is room for improvements, the double-header trains were implemented with great success at Great Noligwa mine. It is currently the preferred tramming methodology at Great Noligwa mine, and is also implemented at other Anglo Gold Ashanti?South Africa shafts. This tramming system has huge potential for growth, not only in Anglo Gold Ashanti, but in all other older mines that experience major tramming problems.

Jan 1, 2008

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992

By Pierre Marcotte

Jackleg rock drills expose their operators to high hand-arm vibration levels. To address this problem, an antivibration handle has been developed. The antivibration properties of the handle were achieved through a suspension based on a hinge design, achieved with a torsion spring and o-rings. To provide some bench marking for this new handle and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. Testing of four antivibration handles on the test bench have shown reductions of the overall weighted acceleration level in the order of 54 % to 60 %, with most of the attenuation occurring in the zh-axis at the rock drill percussion frequency.

Jan 1, 2008

This publication summarizes the in-house and contract research and development projects programed for fiscal pear 1980 by the Bureau of Mines under its Minerals Environmental Research activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau's environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. Through the years, efforts of various Bureau programs have yielded valuable information on the origin and control of many of these problems. With the reorganization of the Bureau of Mines in 1979, the Minerals Environmental Technology program was structured to consolidate these efforts into a single program that will systematically investigate al aspects of mining- and processing-related environmental pollution and damage-from initial discovery of the mineral resource to ultimate return of the land to productive use. In fiscal year 1980, the Bureau received an appropriation of about $21 million to conduct research and development work on these problems.

Jan 1, 1980

By R. G. Hamm

A brief outline covering the shovels and draglines in use in the open-pit mines of Western Canada, including British Columbia, Alberta and the Yukon, is given, followed by the procedure for the selection of the correct wire rope for each application. Such fa ctors as wire rope constructions, lay directions and types of cores are mentioned. Once the correct wire rope has been selected, there are variousfactors that can affect the service fife ofthe rope and the reduction ofdown-time during rope change-overs. Factors such as hairpin winding, types of Becket loops, and shovel drum and bail adaptors are described.

Jan 1, 1979

By K. D. Hester

"1.0 INTRODUCTIONThe uranium industry started in Canada with the reopening of the gravity concentrator at Eldorado's Port Radium mine in the North West Territories in 1942. In 1948, uranium exploration and processing was opened to the private sector, and the Federal government offered special pricing incentives to the industry. Eldorado explored the Lake Athabaska deposits in northern Saskatchewan, and in 1953 opened the Beaverlodge mine. Other mines in the area soon followed. In 1953 also, the deposits in the Blind River - Elliot Lake area and in the Bancroft area of Ontario were discovered. Mines and mills were quickly developed in these areas.Canadian uranium production peaked at 15,900 short tons of U3O8 in 1959. In that year, uranium exports at $300,000,000 exceeded those of all other minerals in value. On October 1, 1959, Canadian uranium operations employed 13,900 people.Up to 1956, it was a seller's market. By 1958, world production of uranium was far ahead of requirements. Accordingly, in November of 1959, the USAEC announced it would not renew it's options for continued delivery of uranium from Canadian mines. This led to the ""stretchout"" of existing uranium contracts, and many mines were shut down (see Table 1) .In the early 1970's, a commercial uranium market seemed to be developing. In Ontario, at Elliot Lake and Bancroft, mines reopened. But competition was coming from the Athabaska basin of Saskatchewan. Currently it is these high grade, open pit deposits of northern Saskatchewan which are in the forefront of Canadian uranium developments. Canadian developments since 1942 reflect the political and market forces, as well as metallurgical progress and changes in environmental standards. This paper attempts to show these process changes in broad perspective."

Jan 1, 1987

Steven F. Leer, president and chief executive officer of Arch Coal Inc. will be the master of ceremonies for the 12th Annual National Mining Hall of Fame Induction Banquet. The black-tie (optional) affair will be held at the Adam’s Mark Hotel on Sunday, Oct. 10 in St. Louis, MO. Six legendary leaders will be inducted at the ceremony. They will join 145 mining greats previously honored in the annual ceremonies. R. Joe Wagner, vice president for exploration and chief geologist of The Doe Run Co., St. Louis, will be the evening’s keynote speaker. His father, Richard Edwin Wagner (1898-1979), was inducted into the National Mining Hall of Fame in 1998 at the banquet in Phoenix, AZ.

Jan 1, 1999