Search Documents

By Lee W. Abramson, Mee Shing Owyang

The Lake Merced Transport tunnel is 18 feet in diameter and 1.6 miles long constructed within dune sands, beach sands, and the Colma Sand Formation. It runs beneath highway right-of-way from an existing pump station near the shore of Lake Merced to a point near the Pacific Ocean, where it will connect with the existing transport/storage tunnel. The final tunnel lining was originally designed as a cast-in-place concrete lining to be constructed within steel ribs and wooden lagging initial support. The contractor opted to use a precast concrete segmental initial lining thus requiring a redesign of the final lining. The redesigned lining incorporates composite action from the initial lining thereby eliminating the need for outer steel reinforcement. A computer model was used for analyses which included operating conditions, ground and construction loads, and possible effects of liquefaction and earthquakes.

Jan 1, 1993

By Mario E. Rossi

The concept of entropy is classical in thermodynamics and information theory. Its potential use as a measure of the ordering of a spatial system is discussed. Although entropy has been discussed previously in the framework of spatial statistics and for univariate distributions, a bivariate data-based estimator has not until now been defined. Different statistical distributions maximize entropy, depending on the univariate, bivariate, or n-variate constraints applied. For bivariate distributions, with a known mean and known covariance, it can be shown that the distribution that maximizes the entropy of the system is the bivariate gaussian. A nonparametric bivariate entropy estimator is introduced, derived directly from the experimental cumulative frequency distribution. Assuming that this experimental bivariate distribution is representative of the population distribution, then a measure of departure from gaussianity can be introduced as a relative entropy estimator. Practical applications for the entropy estimator are discussed, and an example developed.

Jan 1, 1992

By Catherine T. Aimone

A computerized cost model has been developed to simulate the technical and economic effects of strip mine blasting in the vicinity of structures. Current surface mining regulations restrict the allowable level of production blasting as a function of this distance. Blast design modifications,' therefore must be employed when blasting in the vicinity of homes to ensure compliance with federal and state regulations specifying limits to the seismic effects generated from a blast. The blasting level allowed. is computed by the charge weight of explosives per delay from the following scaled distance formula: [ ] where W is the charge weight per delay, in kilograms (pounds), D is the distance factor corresponding to the regulatory limit of peak particle velocity to which a structure may be subjected to. Current regulations specify 2.54 cm (1.0 in.) per second corresponding to a SD factor of 27 (60) (Federal Register, 1977).

Jan 1, 1982

By T. M. Anderson

From the start of production in 1915 until 1948, underground block caving operations accounted for all of the ore production of Inspiration Consolidated Copper Co. Open pit development work began in 1947, and ore production from the open pit commenced in March 1948. Thus began the transition from underground to open pit mining which continued until August 1954. Since then, open pit mining has accounted for all ore production which presently averages 105,000 tons of ore and 75,000 tons of waste rock each week. Open pit mining operations at Inspiration is carried on in two separate pits-the Live Oak Pit and the Thornton Pit. The Live Oak Pit covers an area of approximately 1500x3000 ft and the Thornton Pit, 2500x2000 ft. The geographic centers of the two pits are 4000 ft apart and, at their nearest point, the surface slopes are 500 ft apart.

Jan 1, 1961

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By James M. Reichman

Waterjet assist of mechanical cutters has been demonstrated in a variety of laboratory studies as well as on field equipment. As this technique becomes more widely accepted, it will be necessary to develop methods of minimizing the horsepower and water requirements. In machines such as roadheaders, continuous miners, and longwall shearers, the use of waterjet assist can be optimized through the development of phasing valves. Phasing valves will allow only the cutters in contact with the rock to be assisted. Since only 30 - 40% of the cutters are in contact with the rock, the saving power is significant. Flow Industries has developed a phasing system for use on roadheading machines. This system allows the operator extensive control of the angle of assist as well as the quadrant being assisted. This system could be greatly simplified for production machines and adapted for use in continuous miners and longwall machines.

Jan 1, 1985

By J. H. Berryman

THE use of oxygen as a bath reagent in hearth furnaces during the refining period is a familiar story. Investigations and tests in which oxygen was substituted for iron ore to reduce carbon date back 25 years and include the work of Bigge,1 Browne,2 and Chelius.3 During this past year the majority of the experimental work in the use of oxygen was carried on mainly in open-hearth shops, since it was felt that the greater field for application lay in this type of furnace. Much constructive work was done in evaluating the carbon-oxygen relationships, as reported by Slottman and Lounsberry4 and by Hughes.5 Steelmakers using the electric furnace have been actively engaged meanwhile in an experimental program of their own, with such success that the oxygen injection pipe has become a tool in the day to day production of low-carbon and stainless steels.

Jan 1, 1947

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof-bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60% and 40%, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert and a rigid insert for cleaning the roof-bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the workers coveralls when using either of the inserts.

Jan 1, 2003

By S. Lin, Y. J. Wang

Fan stall is a notorious phenomenon of axial flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts on the stability of the ventilation system are very complicated and not well understood. Results from laboratory experiments indicated that, when a fan is working across its stall zone (i.e., the pronounced trough on the fan characteristic curve), some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a nonachievable quantity range of the branch, because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). This paper discusses these important characteristics of ventilation systems by using results from tests on laboratory tubing networks.

Jan 1, 1998

By Wayne R. Charley

High operating costs and environmental restrictions have combined to increase smelting costs for precious metals to a level where many mining companies cannot afford to operate. The need for a hydro-metallurgical process to produce bullion with an efficient, economical and environmentally safe method is well recognized by the industry. This paper describes the research and development program conducted by Behrent Engineering Company in its investigation of the use of an acidic solution of thiourea for the extraction of precious metals from concentrates and high-grade ores. The areas discussed are: process design parameters, health and environmental aspects and economics of the process. The scope of this paper includes the leaching process, the recovery of precious metals from pregnant solutions and the production of dore'. Thiourea leaching offers a complete alternative to smelting and cyanidization for those concentrates and ores amenable to this process.

Jan 1, 1984

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By R. H. Sweetser

There are so many conditions affecting blast-furnace results that it is hard to get satisfactory comparative data on the working of two furnaces, and much more difficult to get comparable results from the use of two entirely different fuels. The several advantages of charcoal over coke as a blast-furnace fuel have doubtless been apparent to many managers; but probably the conditions for comparative tests of the two were never so favorable as during the year 1905, at the works of the Algoma Steel Co., Sault Ste. Marie, Ontario, which comprise two modern blast-furnaces, well equipped, though of comparat.ively small capacity. For four consecutive months one of these furnaces was run with charcoal and the other with coke. Then the charcoal-furnace ran for a while with part charcoal and part coke; and, still later, with coke only. The ore-mixtures were

Jan 1, 1909

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

By Bunting S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954.2 In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct -325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine.

Jan 5, 1959

By Gloyd M. Wiles

Since D. C. Jackling was famous for his adeptness at organizing and training teams of operating personnel, the subject of mine management is particularly appropriate for a Jackling Lecture. In fact, it is doubly appropriate because in very basic ways Jackling's career changed the nature of the tasks and challenges facing a mine manager. Management of mines, of course, is the art of finding and winning minerals economically from the earth's crust, and it involves the use of all the engineering sciences. But also of prime importance is a skill which is not yet a science-the area of management often referred to as human engineering. Since expenditures on staff and labor may well involve more than 50% of the direct costs of operating a mine, ability at human engineering is just as important as the ability to plan and put into effect the most efficient operating procedures.

Jan 5, 1962

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risks associated with the design of mine waste-management facilities. These experiences show that the technical and managerial challenges of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur in developed and developing countries is indeed re¬markable and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailings storage facilities are, in many cases, more demanding than those of conventional water dams because seepage of fluids that contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 2000

By Heribert F. Broicher

As of 1998 German companies have been engaged in research and development of LIF analyzers for rock identification, i.e. for the fingerprinting of rock by the analysis of laser-induced fluorescence (LIF). Test work in Germany, Sweden and South Africa showed the potential of this new technique, which operates online and in realtime (1). In 2003 the Finnish company IMA Engineering Ltd Oy commenced building and marketing LIF analyzers under the trade name OreSpex. Today, one OreSpex analyzer has been installed in the Kiruna Mine, Sweden to check the phosphorus content of train loads. In 2004 a second OreSpex analyzer was built for dilution control in the Argyle Diamond mine, Australia. In 2005 another LIF analyzer will be used for test work in various mines in the US. The principles of the technology and status of ongoing work are presented.

Jan 1, 2005

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By Yuanping Chen, Yihui Zhao, Yunhe Hong

It is important to study the methane transport phenomenon in a longwall panel under descentional ventilation conditions. The gob area is divided into a number of rectangular percolating elements, each of which is connected with its neighbors by leakage passages, so that a network can be formed. Using the mechanics of porous media fluid flow, the mathematical model of air and gas flows can be established. Based on the existing ground pressure theories, the inhomogeneous porosity of the porous media in the gob can be given. Through computer simulation it is found that air pressure and temperature are functions of position. Air density, viscosity, and natural ventilation pressure are functions of temperature, pressure and methane concentration. It is also found that the resistance varies with air density and viscosity. Finally, the calculation results are given to show the differences between ascentional and descentional ventilation methods.

Jan 1, 1991

By Greg Blerie

The requirements placed on belt conveyors grow increasingly complicated No longer is it sufficient for the conveyors to merely move material from "Point A" to "Point B. " Now these systems must be able to produce a specified flow, guaranteeing a plant can operate as scheduled without peaks and valleys in material flow and production rate. In addition, the conveying system must provide effective control, to minimize the problems and costs associated with the escape of fugitive material these problems include unscheduled shutdowns, premature equipment failures, regulatory headaches, poor neighbor relations, and health and safety issues. The key to accomplishing these goals is the loading and discharge of the conveyor belts. Fortunately, new designs for the chutes that accomplish conveyor loading and discharge can move material efficiently, without blockages and while minimizing the amount of dust generated This innovation is the development of engineered flow chutes

Jan 1, 2004