Search Documents

By T. H. Ramsey, Richard Shield

A process has been developed for fabricating thin-film resistors that are compatible with integrated circuits. Films are produced by evaporation of single refractory metals using an electron beam heating source. Resistor paths are then made using standard photoresist etching techniques. A low-temperature coefficient of resistance is obtained by control of nucleation during deposition of the film. One application of the process has been the development of a discrete resistor used for current setting in linear integrated circuits. Multiple thin-film resistors were formed on oxidized silicon substrates using molybdenum metal as a source. An evaporated protective layer of SiO2 over the resistor prevents resistance changes which might occur during subsequent high-temperature processing. Properties of a typical resistor are as follows: R = 15.7 ohm per sq, tolerance surface dimensions = 0.028 by 0.028 in., stable after 4000 hr at 0. 75 w without heat sink. THIN-FILM resistors have been investigated for many years with a large selection of usable resistors resulting from a wide variety of materials. Many of the processes necessitate a high degree of complexity but in nearly all cases the conclusions have been that the materials used in each case were acceptable provided the deposition process was reproducible and could be controlled sufficiently to give the required tolerances. It is our opinion that simplicity is still the key to thin-film resistor fabrication. In this regard, the single metal is obviously the simplest process to control, provided all the necessary properties can be obtained. The idea is not original in this laboratory by any means. Others have taken this approach.' It has been demonstrated that a fairly wide range of resistivities can be obtained by careful control of deposition parameters for any given metal, and by selection of several single metals a very broad range of stable resistors can be obtained. The transition from one metal to the next is made when a film becomes too thin for adequate process control or long-term stability. A great deal of emphasis is once again being placed on the thin-film resistor. Although they have been thoroughly studied in the past, new applications have been found that require the properties obtainable only from thin-film resistors. Integrated circuits, in general, are advancing toward higher speeds and radiation environments which require replacement of the present diffused resistors. Linear circuits in particular are requiring high-power, high-precision resistors for the more advanced applications. The particular requirements of some linear circuits are such that a discrete resistor is required. The resistor described in this paper was developed as a 15.7-ohm precision discrete resistor for use in a current regulating circuit requiring a +2 pct end of life overall tolerance, a dissipation of 750 mw, and the ability to operate over a fairly broad temperature range (i.e., a low temperature coefficient of resistance, TCR). State-of-the-art integrated circuit and silicon processing technology lends itself well to the fabrication of thin-film resistors. Not only is the resistor thin film well-suited to integration on individual circuits, but the oxidized silicon surface provides one of

Jan 1, 1969

By R. P. Thomas

Secondary fertilizer minerals are the mineral materials used to supply directly and indirectly the secondary and trace plant food nutrient needs of a fertilizer. Since few soils contain sufficient availability of all plant nutrients for their proper growth, man has prepared mixtures of plant food materials to correct these nutrient deficiencies. These mixtures or fertilizers, when added correctly to a soil, make it possible for abundant and economic crop growth. Many kinds of materials are used as sources of these needed nutrients. They come from natural and synthetic materials and minerals including many beneficiated byproduct compounds. A fertilizer consists largely of carriers of one or more of the three major plant foods, namely nitrogen (N), phosphorus-phosphorus pentoxide (P2O5) and potassium-potash (K2O). Many other nutrients are just as essential for plant growth as the three major plant foods. In fact, the efficient use of fertilizers today depends upon an adequate supply of all these other nutrients. Since these additional materials are usually removed from the soil by plants and supplied in fertilizer in less quantities than the major nutrients, they are called secondary and minor nutrients. In the early days these special nutrients were contained as impurities in the primary nutrient carriers. Today, fertilizers are made primarily from concentrated and synthetic materials which carry very few of these other essential nutrients. Consequently, many secondary and trace nutrient carriers, as salts, byproduct compounds and even minerals have to be added to fertilizers. Secondary Nutrient Carriers The secondary plant foods in fertilizer are next to the major nutrients in abundance. They are calcium, magnesium, sulfur, chlorine, silicon and sodium. Although many of these elements are added to a fertilizer as part of the major nutrient carriers, they are also added in special carriers. The large tonnage of these secondary nutrient carriers used in fertilizers represents only a small percentage of the total production of these materials. A fertilizer producer thinks in terms of materials which supply nutrients instead of minerals. Therefore, these materials will be discussed by elements. CALCIUM Soils need calcium to supply the nutrient needs of plants and maintain the desired physical and biological conditions in the soil. The available calcium is usually 40 to 80 pct of the exchangeable bases. (These bases are ones which can be displaced by other cations and determined quantitatively. They are then expressed as milliequivalents per hundred grams of soil-me.) Direct applications of lime materials such as burnt, ground or hydrated limes are the important sources of calcium for the soil. Most crops, especially legumes, have a high requirement for calcium. The average farmer does not use enough lime to maintain the proper level of available calcium. Hence, it is necessary for many fertilizers to contain soluble calcium materials for efficient use of the major nutrients. The following major nutrient carriers supply some calcium: calcium nitrate, ammonium nitrate mixtures and cyanamid, and many of the phosphates. Both synthetic and natural gypsum are used in fertilizer production. Some crops such as peanuts require a large amount of soluble calcium. Gypsum is the important supplier of this soluble calcium. It is not applied with the fertilizer

Jan 1, 1960

By J. W. Stevenson

At this 5th U.S. Mine Ventilation Symposium I would like to focus your attention on safety and the contribution of the ventilation engineer over the past 50 years. This conference affords us the opportunity to express, to listen, and to learn. As ventilation engineers it is indeed an exciting time--a time that not only stimulates our imagination but also pin points our aims in our quest to obtain zero fatalities by the year 2000, the goal expressed by William J. Tattersall, Assistant Secretary of Labor, Mine Safety and Health Administration. In the past, coal mine ventilation has often been unfortunately synonymous with explosions and resulting fires. Those not familiar with us do not recognize the painful evolution of the coal mining industry and particularly the evolution of mine ventilation. To put my presentation into perspective, I recently reviewed a U.S. Bureau of Mines Bulletin No. 586 - "Historical Summary of Coal-Mine Explosions in the United States 1810 - 1958 prepared by H. B. Humphrey Mining Health and Safety Engineer. This bulletin was published in 1960. Mr. Humphrey stated "In 1946, factors contributing to the explosions occurring from 1941 to 1945 were: (1) The rapid increase in the use of electrical equipment at face regions where gas and dust are most likely to be found; (2) the increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost, which in many mines has resulted in neglect of even rudimentary precautionary measures; (3) multiple-shift operation without provision of time for adequate maintenance of equipment, effective rock dusting, and testing for gas; (4) decrease in supervision owing to demands on supervisors for maximum tonnage and loss of competent supervisors to other employment; (5) lack of effective supervision, owing to numerous new conditions, some of them war-connected; (6) inability to obtain adequate equipment repair and replacement parts; (7) shortage of labor and inadequate training of coal-mine workers; and (8) failure of both miners and mining officials to show regard for safety in changing from hand-loading to mechanized methods". Most of the eight factors listed by Mr. Humphrey continue to affect our work lives as mining engineers. The increased demand for coal with the desire to obtain maximum tonnage per machine at minimum cost has never changed. The local and regionalized coal industry of the 40's is today competing against the world coal market. Our mines work or shut down based on cost. This has always been the case. During the five year time-frame Mr. Humphrey was documenting, 345 miners were killed in major explosions. A major explosion was one in which five or more miners were killed in a single accident. In addition, 105 more miners were killed in minor explosions for a total of 450. What a wanton waste of life. What fears, anxieties, miseries, and sufferings were created by these accidents. However, we must remember and keep in mind that the coal mining company officials, engineers, and foremen, the governmental agencies- federal, state, and local - were using the technical tools and knowledge available to operate the mines as safely as they could. Obviously mine ventilation engineering technology was woefully inadequate.

Jan 1, 1991

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By James J. Halbouty

The restraining effects of war conditions on oil-field development are well illustrated by statistics on South Texas † fields for the year 1942. Statistics also show a decline in wildcatting, but this decrease is much smaller than that shown by field activity. In comparison with results in 1941, there was a reduction of about 44 per cent in the total number of wells drilled in the area (802 in 1942 against 1452 in 1941) This 44 per cent drop represents declines of 50.4 per cent in field wells and of 17.4 per cent in rank wildcats. Field wells (exclusive of 18 wildcats that discovered fields) totaled 598; also, 204 rank wildcats were drilled (see Tables 3 and 4). The corresponding figures for 1941 are 1205 field and extension wells and 247 rank wildcats. In this connection, it should be noted that whereas in 1941 the rank wildcats made up only 17 per cent of all wells drilled in the area, their percentage of the 1942 total was 25.4 per cent. In spite of the decrease of 43 in the number of rank wildcatst drilled, there were 18 new productive areas discavered, one more than the 17 new fields found in 1941. Thus the field-discovery rate for 1942, one new field for every 11.3 wildcats drilled, compares favorably with the I to 14.5 rate of 1941. Thirteen new producing levels were opened in fields; this includes the finding of 44' gravity crude on the west flank of the Sejita field in a 5700-ft. sand, which produccs distillate higher on the structure. Interesting, and showing the general scarcity of sand discoveries, is the fact that of the 13 new sands discovered, 7 were found in Jim Wells County. The year's sand-discovery rate of one new level for every 46 field wells compares very unfavorably with the I to 19.7 rate of 1941, during which 61 new producing horizons were found. Developmeilt of new fields was on a small scale. In several instances activity in these areas was not carried beyond the drilling of the discovery well. The field discoveries of 1942, together with the type of production obtained from the discovery wells and the total number of wells (productive and dry) drilled in them, are given below: Discovery Num- Field.I County Well her Produced Wells I. Cadena....... Duval Oil 2 a. Garza......... Duval Oil I 3. Dinn......... Duval Gas I 4. Keller......... Duval Gas I 5. East.......... Tim 0 11 I 6. Green Branch . McMullen Gas 3 7. Frost. .GreenBranch........ Starr Oil I 8. Garcia........ Starr Oil 6 9. Ulrich........ Starr Oil 4 10. Lykes......... Webb Oil 2 11. McLean....... Webb Oil 9 Iz. Alamo........ Hidalgo Distillate 2 and gas 13. Penitas....... Hidalgo Distillate 2 and gas 14. Xmpnan..... Jim wells i a 15. South Premont Jim Wells Distillate i and gas 16. Quinto Creek.. Jim Wells Gas 4 17. Roth.. . :..... Jim Wells Gas I I 18. South Sinton.. San Distillate I Patricio and gas . • See Table 2 for data on discovery wells and Table I for information on these fields. • See Table 4.

Jan 1, 1943

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By A. Brown

RAPIDLY rising world demand for mineral products has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations. In recent years the Mines Branch of the Department of Mines and Technical Surveys in Canada has conducted such an investigation. This report of the work is primarily concerned with stress problems in some Canadian coal mines and, in particular, with mine bumps. Mines Branch investigations of this and related problems are carried out by a small team of mining engineers and physicists who, with assistance from geologists, pool their special skills in an integrated program. These Canadian investigations combine a field and laboratory approach. Since data obtained under contrasting mining conditions allow useful comparisons of ground behavior under stress, this article will present data gathered under a wide range of Canadian coal mining conditions. Two contrasting longwalls in eastern Canada will be discussed and two dissimilar pillar extraction operations in western Canada. Locale of Observations In eastern Canada observations are being made in the collieries at Springhill, Nova Scotia. The district's No. 2 mine, which has a history of bump occurrences dating back to 1917, is currently being worked at a depth of 4200 ft. The mining method is longwall retreating along the strike and the practice is to retreat three walls in line, each about 350 ft long. There is no machine cutting or shooting—the coal is hand-picked and hand-loaded onto face conveyors. There are three rows of hardwood chock block supports parallel to the coal face. These supports are built during the two daily coal loading shifts, and the rear line is withdrawn during the midnight shift. The goaves are partially packed by stone midwalls 12 ft wide which are built forward daily in step with the face advance. The seam dips at 15° and averages 9 ft of strong, well cleated bituminous coal enclosed in competent beds of shales, sandy shales, and sandstones of Carboniferous age. The bumps rarely disturb the retreating longwall faces but manifest themselves as violent upthrusts of pavement in the levels leading to the walls. Observations have also been made in Springhill's No. 6 mine, which operated in a 5-ft seam of coal at a depth of about 2500 ft. Although No. 6 mine was

Jan 1, 1959

By R Bertuzzi

This paper presents a three-dimensional analysis of a trapezoidal-shaped segmental tunnel lining for a recent tunnelling project in Sydney. Two- dimensional analyses, hand calculations and equipment selection defined the lining geometry and loads. The analysis, which was undertaken using 3DEC (Itasca), included a complete ring of six segments bolted together to assess the impact of imperfectly built rings. Asymmetry was induced in the analysis by unfavourable positioning of segments within construction tolerances. Model output includes displacement and stress within the entire ring and normal, shear and bending moments at the joints. For the case analysed, the results suggest a 10 mm construction tolerance increases normal and shear stresses along the radial joints by approximately 25 per cent and 15 per cent, respectively and up to a doubling of the induced moments.

Jan 1, 2008

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Dick T. Atkinson

This report describes the Foster-Miller program that designed, developed, built and tested an automatic, remote control mine car coupler. This new coupler gives the motorman the capability to selectively couple and uncouple cars from the locomotive, to transmit braking intelligence to the coupled car s and to determine if the trip is intact. Hazards due to derailment and runaway cars will be reduced as the brakes are automatically applied in any uncoupled car. Laboratory tests described herein have been completed on the coupler set. Applications include, but are not limited to, the unit train system.

Jan 1, 1976

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Jacek Paraszczak

Numerous problems encountered in the mining of narrow vein deposits challenge the productivity, competitiveness and profitability of many mines. Mechanization of mining operations is one of the most important means to ensure the healthy survival of this mining sector. Vein deposits account for nearly all the world's primary silver production, as well as a significant portion of gold, tin, copper lead and zinc. In North America, narrow vein mining constitutes an important sector of the industry. Operators exploiting such deposits are concerned with the most appropriate mining method and equipment to mine in such a way as to minimize waste rock dilution. Unfortunately, most of the equipment available does not meet the additional geological and economical restrictions typical of narrow vein mining. Thus, mining these deposits is labor intensive and can result in low productivity. Consequently, the profitability of many such mines is reduced. Increased mechanization is one of the solutions to ensure their healthy survival. This paper reviews the state-of-the art in mining equipment with reference to narrow vein mining limitations. Problems encountered Geological conditions and economical factors have a decisive impact on the choice of mining method and equipment. Many ore bodies are relatively small, usually erratically distributed, often less than 2 m (6.5 ft) wide, with dips ranging from 0° to 90°. To make things worse, ore body limits are sometimes difficult to determine and the ground is hard and abrasive.

Jan 1, 1992