Search Documents

Capital, as represented by mineral resources, is being exhausted rapidly without possibility of identical replacement. The public must be discouraged from thinking-why worry about the bank balance so long as there are plenty of blank checks? Instead of each man, woman, and child being owners of a mineral capital of $89,000 as former Secretary Ickes once stated, they are really the guardians of a mineral reserve which, when harvested, cannot be reproduced. The proper use of this material is the basis of modern civilization and military power. The best American institutions cannot be maintained or transmitted to our children unless this trust is guarded. It is unfortunate that more attention has not been focused on the fact that this country is headed for a have-not status in the family of great nations if some- thing is not done to preserve its mineral heritage. It is the privilege of the United States now to champion and implement democracy because it is industrialized and can get at its raw materials. A high price is being paid every day in mineral depletion for the privilege. No one can eat his cake and have it too. The United States still must face world-wide economic competition and, perhaps, World War III. In the final analysis all wealth comes from the ground, whether plant, animal, or mineral. Value is in-

Jan 1, 1950

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By K. J. Miller, R. E. Hucko

The Coal Reparation Division of the Pittsburgh Mining Technology Center conducted an investigation to assess and compare the pyritic sulfur reduction potential of coal-pyrite flotation and high-gradient magnetic separation (HGMS). Tests were run on three coals - an Upper Freeport bed coal, a Lower Kittanning bed coal, and a Pittsburgh bed coal - to establish grade-recovery relationships characteristic of both processes. Representative portions of each coal sample were crushed to two top sizes-nominal - 500 pm (-35 mesh) and nominal - 149 pm (-100 mesh)-and subjected to conventional froth flotation. The froth product was then beneficiated by coal- pyrite flotation or HGMS, to provide a direct technical companion of the two processes. At - 500 pm (- 35 mesh), the size normally employed for coal flotation, both coal-pyrite flotation and HGMS effectively separated pyrite from coal, and the performance of the two processes was essentially the same. At a - 149 pm (- 100 mesh) sire, however, the performance of HGMS exceeded that of coal-pyrite flotation. The separation effected by HGMS were more efficient at - 149 pm (- 100 mesh) than at - 500 pm (- 35 mesh). On the other hand, it was concluded that either the effectiveness of coal-pyrite flotation decreases with diminishing top size or the process has not been optimized to treat material finer than 500 pm (35 mesh).

Jan 1, 1983

By N. J. Themelis

It is a pleasure to introduce this session on frontier technology and present an overview of pyrometallurgical technology, as it is today and where it may be heading. While there have been many advances in hydro-metallurgical processing in our times, pyrometallurgy has not been still, and more novel processes have been introduced in the last four decades than in all previous ages of humanity put together. As a result, pyrometallurgy has managed to remain the predominant mode of producing metals from ores and concentrates: over 95% of the world primary metals production, including iron, manganese, copper, lead, chromium and nickel, is obtained via the high temperature route. Some of the characteristics of pyrometallurgy, along with the corollary industrial advantages are shown in [Table 1]: [ ] On the other hand, the necessity of operating at high temperatures also entails special problems and it is unfortunate that research on how to overcome these problems has not, in most cases, kept up with the development of these wonderful novel processes. We shall first speak of the important developments in pyrometallurgy which have brought us to the current state of the technology, and subsequently on the problems still encountered and the kind of research and development that will be necessary to bring pyrometallurgy on a par with other late twentieth-century technological developments.

Jan 1, 1985

By E. E. Krist, W. H. Sweetser

Sampling of an orebody has a number of purposes. In the initial phase, it is necessary to define the limits of the orebody and mineral content to the extent that it can be stated whether it is, in fact, an economic orebody. Also, samples must be generated so that geological and metallurgical evaluations can be made. Finally, when sufficient information concerning the geology, mineralogy, and metallurgy are known, a mining method and plan can be developed and the metallurgical; plants constructed to process the ores as they become available. With today's large, complex open pit copper mines, single sampling methods would be inadequate. Diamond drilling, percussion drilling, underground shafts and drifts all play a part in the total orebody, definition. At Anamax Mining Company's Twin Buttes mine, sampling and orebody definition.wil1 eventually lead to the existence of three metallurgical processing plants and, perhaps, an underground mining operation. A 30 000 tons per day sulfide concentrator was placed in operation in September 1969 and a 10 000 tons per day oxide leaching plant was placed into service in May 1975. The aim of this presentation is to historically discuss the orebody sampling that has been done at Twin Buttes, briefly describe the orebody, and discuss the analytical methods currently used to assist the geologist, metallurgist and mine planner in their respective evaluations.

Jan 1, 1978

By W. Blaschke, E. Malysa

INTRODUCTION In recent years in Poland, a problem connected with the occurrence of a considerable amount of liberated galena grains in size fractions under 1mm has arisen in the zinc-lead processing area. Operating practices have included crushing of ore particles under 0.2 mm followed by flotation. Jigs were applied to separate the concentrates from size fractions under 10 mm and to prevent the galena overgrinding. However, the fractions being too wide, the jigs have not worked effectively, in spite of the great differences in specific gravities of galena, blende and gangue minerals. Fine galena grains move into light fractions in considerable amounts and hence are overground. Therefore, the flotation becomes difficult and galena is lost in its tailings. These losses could be avoided by introducing separation in the grinding and classification circuits. The amount of 0-1 mm fraction is great; therefore, the application of concentrating tables or other kinds of jigs is impossible from an economic point of view. Taking these factors into account, the possibility of application of pinched-sluices was investigated. These are simple devices without moving parts, they have a high output for the unit areas, and their water and energy consumptions are low. In this paper, the results of zinc-lead ores beneficiation in pinched-sluices are presented.

Jan 1, 1980

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By H. Landsberg

Biological as well as geological research has made very successful use of the qualities that the physicists have detected in radioactive substances. Outstanding examples for the vast new fields opened in this part of the border-land between the disciplines of geology and physics are the "radio thermal geology" [July, 1909, see 1 of "References" at end of paper] and all that is connected with the use of the radioactive disintegration clock for the age-determination of rocks and minerals [2]. In structural geology, not unlike to recent bi-ological uses of radioactive material, their "tracer" properties were helpful. Changes in Radon concentra-tion in soil-air, especially accumulations, led to hidden crevices and fault-zones. High contents of Radon in spring-water gave clues as to the types of rocks they had flowed through [3, 4). One specific application of the small admixtures of radioactive material, however, has only lately found some atten-tion and that is their use in linking beds of sedi-mentary strata otherwise only poorly identified be-cause of the lack of fossils or other characteristic properties. To be useful for this purpose, two con-ditions have to be fulfilled: (1) The amount of radioactive material per unit-weight of rock in a given horizon should be uniform over a large area; (2) this same amount should change fairly rapidly in the vertical succession of layers.

Jan 1, 1940

By Voorhees JS, Bureau G

To operate a mine in California requires compliance with State environmental regulations, including assessment of risks and associated financial assurances for postulated worst case catastrophic event scenarios. Carson Hill Gold Mine, an open pit, heap leach operation, completed new risk assessment catastrophic event analyses in 1988. The risk assessment was performed at the same time that a new leach site (Leach Site 3) was being designed. Leach Site 3 is located about 400 m upslope of New Melones Reservoir, which is a public recreation facility and a source of drinking water. Release of leachate (pregnant solution) or ore containing cyanide and metals from Leach Site 3 into New Melones Reservoir was considered to pose the largest risk of environmental damage.Flow failure of the ore heap, potentially induced as a result of liquefaction of the saturated portion of the ore, and/or overtopping of the leach site containment embankment due to excessive precipitation were found to be the most plausible leachate release scenarios. Yearly combined probabilities of various downstream release volumes were estimated. The release volume corresponding to a yearly probability of 0.05 percent was then used to estimate potential environmental impacts and mitigation costs. The costs include earthwork to restore the geometry of the ore heap and repair the fill slope below the Leach Site 3 containment, and impacts on New Melones Reservoir.

Jan 1, 1990

By Bruce S. Brown, Jeremy P. Haile

The construction of tailings facilities and heap leach pads for gold mining operations generally requires the installation of one or more impermeable liners beneath the structures to satisfy environmental regulations and prevent the leakage of gold bearing solutions. Liners are usually constructed using clay soils or synthetic membranes, such as high density polyethelene. Low permeability soil liners can be constructed from natural clays, well graded soils with only a small clay content, or sandy soils blended with a small quantity of imported clay such as bentonite or kaolinite. The permeability of such materials, prgperly pped with good quality control, generally lies in the range of 10- to 10- cm/s, and can be designed to meet minimum prescriptive standards set by regulatory agencies. Important benefits resulting from the use of clay liners include the slow rate of penetration of a saturated wetting front, the decrease in permeability of the liner as it consolidates under the applied load of tailings or ore, and attenuation of potential contaminants in the process solutions. Synthetic liners can be attributed a finite permeability as a result of minute perforations and seaming deficiencies, and possess none of the above properties. Synthetic liners are also, by their nature, relatively thin and even a small head build-up above the liner will result in a large hydraulic gradient across it.

Jan 1, 1988

By C. W. Eggert

"The idea for this talk came to me last year when I was attending the Canadian Gold Metallurgists Meeting. I talked about it to a friend of mine who is an authority on mineral dressing, particularly the theoretical end of the business. He remarked that this was an excellent technical note, why don't you write it up. This is what I have for presentation this morning. I hope in presenting this type of idea in this way it is in keeping with the tradition of the Canadian Gold Metallurgists which was to function on a not too sophisticated level and where operators could get together and trade ideas in an informal way.My basic thesis is that it should be possible to evaluate screen analyses by the application of the standard statistical probability theory. In any statistical analysis the sample is the first consideration. If we look at existing methods of size evaluation we find it is usually based on the fact that a given particle will pass one square aperature and not another. One system of standardizing how these aperatures will be set up is based on Rittenger' s work with the ratio of hole sizes proportional to the square root of 2. Keeping in mind the limitation we have accepted this as our method of 11 sizing"" in attempting to apply standard statistical methods to screen analysis."

Jan 1, 1968

Characterising the weight percentage of each mineral in base metal ores is an integral part of assessing the quality of an ore in terms of its processing properties. The Rietveld method, which uses X-ray diffraction data, has been applied to routinely quantify the minerals in lead/zinc and copper ores from Mount Isa Mines Limited and supergene copper ores from Ernest Henry Mining as well as their related products from the concentrators. The Rietveld method has been tested by comparing Rietveld mineral data with a standard sample with known mineral weight percentages and comparing Rietveld mineral data with mineral data calculated from elemental assays where the element only exists in one mineral such as lead in galena. Where this latter situation does not occur, the Rietveld method has been checked with both elemental and optical microscope data. In all cases, there is a good correspondence between the Rietveld data and the data it was checked against with absolute differences generally in the range of 0.5 to 3 wt per cent. The Rietveld method generally quantifies all minerals occurring over 1 wt per cent in one analysis and is less expensive and more routine compared to traditional methods such as optical microscope point counting. The Rietveld method can be applied to many stages of the mining cycle such as exploration, feasibility studies, mining, minerals processing and for environmental studies.

Jan 1, 1998

By Nick Barton, Harald Hansteen

The deformations resulting from excavation of very large openings are compared using two-dimensional F.E. continuum analyses and discontinuous physical models (20,000 discrete blocks). Both the joint orientations and the model horizontal stress levels were varied. Some models were dynamically loaded to simulate earthquakes (0.2-0.7 g). Model deformations were recorded using photogrammetry. The changes in deformation when increasing the simulated spans from 20 m to 50 m were of particular interest. High horizontal stress caused surface heave when joint orientations were favourable for arch stability. Joint orientations also determined whether the pillars between parallel openings were in a state of compression or tension. INTRODUCTION The engineering performance of large rock caverns has traditionally been learned from mining and hydro power projects, where the depth below surface is often many times greater than the span of the openings. Deformations measured in the walls and roofs of hydro power caverns generally range from about 5-50 mm, though there is a documented case where a wall moved in 126 mm (1), and another where the arch moved down 147 mm (2). The chief objectives of the present studies of large near-surface openings were threefold: (i) to provide deformation data to compare with monitored data from planned engineering projects involving large span near-surface excavations, e.g. underground sports complexes, civil defense shelters, nuclear power stations,

Jan 1, 1979

By Raymond H. Young, Paul Sennett

INTRODUCTION Kaolin clay, consisting largely of the mineral kaolinite, is widely used as a white pigment. In the United States, for instance, pigment kaolin production was nearly 6,000,000 tons in 1976 (1). Production for this year should be significantly above this level. Current prices for kaolinite 'pigments range from about $20.00/ ton to$260.00/tony,depending on the amount of processing needed to make the final product. Although much of this pigment kaolinite is used as an inert filler where product specifications are not very rigid, a large quantity of kaolinite is converted to products where very restrictive specifications exist. These specifications set severe limits on such properties as viscosity in a water suspension, particle size distribution, color, and brightness. This discussion will concentrate on methods available to improve the color and brightness of pigment kaolin and will review the advantages and problems associated with these various methods. The term "brightness" refers to the reflectance of the pigment to blue light (2). Since even the brightest commercial kaolins have a somewhat yellowish color, the blue reflectance (or brightness) is a reasonably good measure of their nearness to a perfectly white material. I KAOLINITE STRUCTURE AND SOURCES The mineral kaolinite is an aluminum silicate and can be represented by the formula (OH) 8Si4A14010. The formula is frequently written

Jan 1, 1979

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By Ajoy K. Ghose

INTRODUCTION Longwall mining made its debut in Indian coal mining scene around 1900. Despite this headstart, the application of the method has been slow and halting. Currently, there are some 16 operating longwall faces only in different Indian coalfields contributing to perhaps less than 3 percent of the total underground coal production. Ambitious plans for expansion of longwall mining notwithstanding, apprehensions on the cavability of Indian coalmeasure roof rocks and some unsavoury experiences with face collapses in caved longwalla have impeded wider adoption of the technique. Between 1960 and 1983, some 41 caved longwall faces were worked in Jharia, Raniganj, Karanpura and Korba Coalfields in India, of which 6 faces reportedly had collapsed(1). The first powered support longwall face was started in August 1978 at Monidih colliery which marked a major step forward in the introduction of advanced technological system in Indian coal industry. This paper attempts to analyse critically the experiences with longwall ground control in caved longwall faces in India. Experiences from powered support faces at Monidih, Dhemomain and Pathakhera are synthesized to provide an appraisal of the present status of caved longwall faces under the Indian coalmeasure roofs, which thus far have been characterised as “massive”. The geotechnical site factors at the powered support faces are evaluated and conclusions drawn on the pre-assessment of caving characteristics and support resistance required at the faces.

Jan 1, 1984

By William L. Grube

PECIMEN preparation for electron metallography involves several steps, such as polishing, etching, replicating, mounting, and shadowing. Although each step must be done with care, the operation requiring the utmost attention is etching. Proper etching is important because the relief pattern developed on the surface of the specimen by the etchant, and reproduced as minute differences in thickness of the replica, determines entirely the amount of detail seen in the final micrograph. The characteristic colored stains, sometimes used in light metallography to simplify identification of certain microconstituents, cannot be tolerated because there is danger of introducing artifacts in the replicating operation. It is also quite difficult to remove plastic replicas from stained specimens. A suitable etchant for electron metallography must, therefore, in all cases exhibit a preferential attack upon each of the microconstituents present sufficient to result in a difference in surface elevation. When only two microconstituents are present, it is not too difficult to find a suitable etchant since their physical or chemical properties are generally sufficiently different to result in a marked difference in attack by the etchant. For example, picral (a saturated solution of picric acid in methanol used as an immersion etch) is a satisfactory etchant for the specimen shown in Fig. 1 consisting of iron carbide particles embedded in a ferrite matrix.'

Jan 1, 1952