Search Documents

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By E. R. Davis, R. J. Knott

The paper discusses some of the tools of management in the field of project control, especially in engineering. Project control includes planning and cost engineering, and involves various phases: the conceptual Design and Planning Phase, the Definitive Design and Capital Budgeting Phase, and the Implementation Phase. Each of these phases is discussed in in, together with the use that can be made of data banks, progress reports, and computer systems.

Jan 1, 1982

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland.   Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz.   Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this.   Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By Wei Huang, Anh V. Nguyen

"Potash flotation is an industrially proven success of flotation of soluble salts, but its collector adsorption mechanism remains elusive. In this paper, specific ion effects in NaCl-KCl flotation with carboxylate collectors were investigated. Flotation recovery and contact angle were determined as a function of brine composition of NaCl and KCl. The experimental results have shown that wettability of KCl and flotation of the soluble salts with laurate collectors were dependent on brine ion composition. Specifically, adding Na+ to brines decreased hydrophobicity of KCl crystals and their flotation recovery. Both KCl and NaCl could be floated with laurate collectors. However, flotation of NaCl was greatly enhanced by adding K+ to brine whereas flotation of KCl was significantly suppressed by the presence of Na ions. The decrease in KCl recovery upon adding Na+ is attributed to the counter-ion binding in the pulp. The flotation recovery enhancement of NaCl in the presence of K+ is explained by two effects: 1) increasing K+ concentration leads to a better dispersion of collector colloids in the pulp and 2) K+ enhances the collector adsorption at NaCl crystal surfaces. The water affinity matching rule can explain the specific ion binding behaviors and supported by the SFG spectroscopic results.INTRODUCTIONPotassium is an important fertilizer. Its primary source comes from potash ores, which are a mixture of sylvite (KCl), halite (NaCl) and many other complex double salts such as carnallite (KCl·MgCl·6H2O), alkali nitrates such as KNO3 and NaNO3, and sulfates-langbeinite (2MgSO4·K2SO4) with water-insoluble minerals such as clay and carbonate minerals. Previously, these salts were recovered with a lengthy hot leaching method, with further crystallization of potassium salts from saturated saline solutions. Selective flotation has been preferred since 1940s. Various collector adsorption mechanisms have been proposed soon after the industrial introduction of potash flotation. These include the formation of the insoluble compound model (Halbich, 1933; Singewald, 1961), an ion exchange model (Fuerstenau and Fuerstenau, 1956), a heat of solution model (Rogers, 1957), the surface hydration model (Schubert, 1988), the surface charge model (Roman, 1966; Miller et al., 1992), the interfacial water structure model (Hancer and Miller, 2000) and the colloid adsorption model (Leja, 1983; Burdukova and Laskowski, 2009). Most of the early exercises attempting to propose a unified rule on collector adsorption mechanisms can be seen as heroic endeavors due to the consideration of a vast number of salts in the pulp including alkali halides, nitrates, and sulfates, even the practically insoluble heavy earth metals. Additionally, several types of surfactants with different polarization features and alkyl chain length have been employed. As for the recent models, due probably to the preferential application of long chain amines as collectors in industrial potash flotation, most researchers are only devoted to collectors with low polarization features like amines and sulfonates (Hancer and Miller, 2000; Du et al., 2014). Collector adsorption mechanisms are therefore proposed based largely on a neglect of carboxylates as collectors. However, carboxylates remain an important collector type in soluble salt flotation systems where both salt minerals can be floated using anionic collectors and cationic collectors. Fatty acid type collectors are still one of the widely used collectors for soluble salt flotation and also one of the first to be applied on an industrial scale for the separation of potash ore (Hernáinz et al., 2003; Titkov, 2004). Here we examine some recent models that are relevant to our study to reveal a long neglected specific ion binding effects in potash flotation."

Jan 1, 2016

By Long Han, Jianyuan Liu, Ping Ying

"Particle-bed compressive stressing is the main work mechanism of comminution by high pressure grinding rolls(HPGR). An experimental study on comminution and mineral liberation of two copper sulfide ores was carried out using a piston-die compressive stressing rig to simulate the situation of comminution with HPGR as the final-grinding device. The tests carried out include compressive comminution tests on particle-bed with narrow-size feed, and the locked-cycle comminution test on particle-bed with broad-size feed, which was then compared to a corresponding locked-cycle test of ball-mill grinding. The narrow-size feed is made up of particles in the size range 2.36~3.35 mm, whereas the broad-size feed of particles in the size range 0~3.35 mm. The liberation analysis for copper-mineral in the comminution products was accomplished using BPMA system – an automatic mineral liberation analyzer developed by BGRIMM. The influences of the stressing intensity and the method of comminution on the copper mineral liberation are discussed in terms of product size distribution, copper-metal deportation among size fractions, distribution of copper mineral among particle-size and particle-grade classes, degree of mineral liberation in size class as well as degree of mineral liberation overall.INTRODUCTION Traditionally, comminution process commonly applied in mineral processing is a flowsheet consisting of crushing of crude ore with conventional crushers, followed by grinding of the crushed ore in tumbling mills. In last decades, the energy-efficient HPGR (high-pressure grinding rolls) has found its application in mineral processing, mostly as tertiary or quaternary crusher to generate a fine-crushed product either as feed to subsequent grinding or as feed to a pre-beneficiation process before further grinding. Compared with the process of conventional crushing followed by grinding in ball mill, this mode of HPGR-application can achieve energy saving to some extent by reducing particle size of the feed to ball milling, and by reducing amount of the feed to ball milling if a significant portion of tailings in relatively coarse particle-size range can be discarded at the pre-beneficiation stage. In recent years, the approaches of letting HPGR take more comminution work from ball mill by applying it in semi-finish grinding mode or even finish grinding mode have been discussed (Burchardt, 2014). Although HPGR finish-grinding has been successfully applied in the cement industry for grinding of cement clinker and raw materials, this mode of HPGR application has yet rarely been implemented in mineral processing, despite the advantage of more energy-saving and other potential benefits such as preferential breakage, internal damage of particles and enhanced mineral liberation which may lead to a better downstream processing performance. The reasons for the retardation of the progress of this kind of HPGR-application in the mineral industry lies not only in that a finish-grinding with HPGR has to be operated in dry condition whereas most of ore-beneficiation processes like flotation are operated in wet condition, but also in that there are large variety of ore materials with various complexity of processing technology, which need to be addressed on a case-by-case basis with a lot of test work, in order to evaluate the potential advantages or disadvantages of this application."

Jan 1, 2018

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net-zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields, leaving mining engineering as one of the less preferred career options for students. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, upskilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of humanitarian engineering (HE) in 2020. HE is a sociotechnical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (Menéndez-Aguado et al., 2023; Smith et al., 2023). By focusing on sustainable development, community engagement and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency. However, developing skills toward humanitarian engineering and sustainable mining among new generations of mining professionals remains a complex task. Integrating the necessary content to prepare future engineers for the multifaceted demands of the industry into a single study program poses significant challenges. To address these complexities, modern educational approaches such as the ones integrated in the mining engineering programs at Clausthal University of Technology can be leveraged to enhance both teaching and learning experiences (Binder, 2024b; Bothe-Fiekert et al., 2023; Nowosad et al., 2024). Innovative teaching methods, such as blended-learning, project-based learning, case studies, scenario simulations and interdisciplinary collaborations, can help bridge gaps by fostering critical thinking, creativity and empathy among students. By embracing modern pedagogical strategies, institutions can better equip future engineers to navigate the evolving landscape of the mining industry responsibly and effectively.

Dec 1, 2025

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By Z. Henderson, J. Saylor, L. R. Mendoza

"Diesel particulate Matter (DPM) is a byproduct of fuel combustion in diesel engines. It is classified as a carcinogen, with associated respiratory and cardiovascular health effects. The composition, size, and concentration of DPM is dependent on factors such as engine type, loading and fuel composition. Though a number of DPM abatement and control strategies currently exist, particularly in underground mining environments, occupational exposures remain a serious health concern. As a novel abatement approach, DPM scavenging by fine water or “fog” droplets has been proposed and a laboratory set-up has been built to test the efficacy on engine exhaust. Here, we describe a series of tests that varied engine load, system flow rate and fog drop number density. While none of these factors had overwhelming effects on the results within the ranges tested, the improvement in DPM mass removal attributed to the fog treatment was about 45% on average in comparison to no treatment. INTRODUCTION Diesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy1. More recently, however, adverse health risks of diesel exhaust have become increasingly clear. Many of these risks are associated with the physical and chemical properties of exhaust components1–3. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are a mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash3. The OC fraction of DPM results from unburned fuel and lube oil, whereas EC or soot is formed during the combustion of locally rich regions within the fuel. DPM is classified as a carcinogen6,7 and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustion-related fine particulate and increased cardiovascular and pulmonary diseases8,9. Diesel engines operate in relative fuel rich/oxygen lean conditions and are characterized by relatively high emissions of particulate as compared to spark-ignition engines2,3,10. Typically, these emissions range from 107 – 109 particles/cc and cover two primary size ranges: the nuclei mode where particles have diameters less than about <50 nm, and the accumulation mode where diameters are from about 50-10,000 nm. Most OC resides in the nuclei mode as semi-volatile compounds, while most EC is in the accumulation mode3. The physical and chemical properties of DPM vary with the type of engine, fuel (e.g., petro- vs. bio-diesel) and operating conditions such as loading (i.e., a function of torque and rotational speed)2,3,9,11,12. Loading is a particularly important factor with respect to DPM toxicity9,13,14, and on the effectiveness of after-treatment technologies2,3,15. Engine load alone can affect the EC/OC ratio, and the size distribution and number density of DPM. For diesel engines, the load is roughly proportional to the equivalence ratio3, defined as the actual fuel/air ratio over the stoichiometric fuel/air ratio for complete combustion. Light loads generally favor the formation of OC and small particles. As load is increased the volatiles are oxidized leading to larger soot particles (i.e., EC), but lower total number density of DPM. With further loading, the formation of soot offsets the decrease in volatiles, resulting in increased DPM mean size and number density3."

Jan 1, 2017

By M. U. Khan

"Underground mine diesel equipment generally offers more flexibility as compared to electric powered systems. Diesel exhaust is an adverse agent which affects the health of underground miners. The National Institute of Occupational Safety and Health (NIOSH) regard diesel exhaust as carcinogenic. The NIOSH 5040 method is an established technique for measuring Diesel Particulate Matter (DPM). This process inherently involve a lag time before an accurate exposure determination can be made during which miners are potentially overexposed to DPM. This issue can be addressed by using realtime DPM monitors. This paper presents underground mine shift average based and realtime monitored DPM values monitored in US mines. A FLIR Airtec instrument has been used for realtime measurement whereas shift average based DPM has been determined by the use of NIOSH 5040 method. A log of diesel equipment movement was kept. DPM concentrations versus time were plotted and analyzed. High DPM sources were identified and the FLIR Airtec was demonstrated to be satisfactory for realtime DPM measurements. INTRODUCTION The use of diesel equipment in mines is an attractive option due to its ability to convert a large fraction of available energy into useable work. Diesel engines are rugged, dependable and fuel efficient. It is very common for diesel engines in heavy duty trucks to have a life of 1,600,000 km [Anon, 1999]. Generally in underground mines compared to electric powered equipment, diesel equipment provides more maneuverability. It can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment keeping in mind the recent developments in other energy alternatives [Anon, 2001a]. A harmful aspect to the use of diesel as a fuel is its resultant emission as an adverse environmental exposure agent. Generally diesel particles are approximately one order of magnitude smaller than respirable dust aerosols in underground mines (typically less than one micron in size) [Kittelson, 1998]. Force of gravity has less effect on DPM due to its small particle size. The phenomenon of less gravitational attraction increases the settling and residence time of DPM in the mine atmosphere. High residence time of DPM as compared to other mechanically generated particles increases the chances of diesel particles deposition in the human respiratory tract. The small sized diesel aerosols penetrate deeply into regions of the human lung [Morawska. et al. 2005], which increase the health risks associated with long term exposure to diesel aerosols. Published studies documented the adverse health effects of DPM exposure [Walsh M.P., 1999]. Continuous and long term DPM exposure can result in respiratory disease, lung cancer, reduced lung capacity, and heart disease. NIOSH has declared that the reductions in DPM exposure would reduce cancer risks. In underground mines DPM determination is a challenging task and it is becoming a matter of serious concern due to the harmful health effects associated with the exposure of DPM. The current study involves the determination of realtime and shift averaged based DPM in underground mines of United States of America (USA). Realtime DPM was measured using FLIR Airtec monitors and shift averaged based measurement was performed by the MSHA approved NIOSH 5040 method. FLIR Airtec uses laser scattering approach to measures the Elemental Carbon (EC) component of the DPM. The results from the FLIR Airtec were compared with the results of NIOSH 5040 method and its performance was found satisfactory."

Jan 1, 2015

By P. R. Richardson

"Milling is the weak link in the process chain of many mineral operations. While this activity accounts for only a relatively small proportion of the direct costs of most mineral processing complexes, there are intangible and indirect costs associated with milling which are extremely large. For example, significant opportunity costs are associated with the relatively low yields which characterize this stage of the process.There are changes abroad in the world which I believe are going to cause us to reformulate the whole concept of milling. Increased competition in mineral markets are going to force managers to look anew at the high mineral values reporting to tailings which are a high opportunity cost for many operations. Tailings recovery plants are not the ultimate solution to this problem. Greater environmental concerns are going to increase the costs associated with tailings disposal and force the mining industry to look for other ways to dispose of waste products. Technology changes currently underway in manufacturing and other process industries, such as the automated 'lights-out' plant are going to be brought into this industry, and the changes will be dramatic.These are major long term changes which probably seem rather remote to many managers and professionals in existing operations which are faced with much more mundane challenges arising from day-to-day operations. However, I believe that milling is increasingly a 'lean and keen' operation involving fewer and fewer people, but who are increasingly skilled and professional. Traditional cost management approaches are no longer adequate and the industry has to take a new look at the nature of cost reduction in this core activity. This stage in the mineral process provides opportunities for value creation leading to a significant unit cost advantage for the corporations willing to adopt a total cost approach."

Jan 1, 1988

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan&apos;s upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

By Hodjat] [Shiri

A 4-legged jacket structure was installed by an Offshore Installation Contractor (OIC) in the Persian Gulf. In addition to four open-end pipe piles, six conductors were installed by OIC. During the installation of the piles and conductors, some cemented layers were encountered, which had not been accounted for in the foundation design performed by an independent well known offshore geotechnical site investigation contractor (OGSIC). Six months later, the Drilling Company (DC) hired by Client to execute the wells, reported that all of the six conductors were presenting anomalies, such as vertical misalignments up to 10o and/or collapse of the conductors tip and mid height. The DC faced with serious problem in drilling of the wells and in spite of several times milling the conductors and spending 40 days unpredicted extra time, some of the routes could not be opened and Client lost millions of dollars due to direct and indirect associated costs and expenses. This paper presents a complete overview of all engineering, construction and specially geotechnical investigations and shows that how an inaccuracy in interpretations of the results of an offshore geotechnical site investigation as the main reason in this case study can cause serious damages to whole project with unbelievable time and cost impacts some times up to millions of dollars.

Jan 1, 2006

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004

By A. E. Kasten

The contract objective was to develop and test automatic fire control systems for large surface machinery in surface coal mines. The effort described by the report covers the period from 31 January 1977 to 11 November 1977 and accomplished the following tasks: ? Data accumulation, mainly from visits to the major manufacturers and mine sites. ? Hazard analysis of blast-hole drill, mining shovel, and dragline. ? Recommended design concepts for automatic fire control systems for each of these vehicles. ? Detail system designs for each of these vehicles. ? Procurement of prototype systems for the blast-hole drill and mining shovel. ? Installation of the prototype systems on machines at a surface mine and demonstra¬tion of performance by fire tests on the machines.

Jan 1, 1977

By Nicholas P. Callas

This report presents research results obtained in the investigation of deviation control of boreholes in the rotary drilling process. The approach taken in this research is the passive method of placing stabilizers in the bottom-hole assembly to control deviation. Extensive use was made of the drill string mechanics theories of Lubinski and Woods. Analog, digital and hybrid solutions to variety of boundary value problems were investigated in order to determine the best models for bottom-hole assemblies. Field drilling data was analyzed and the results obtained from various models were compared to the actual drilling results. Various accomplishments of this work have been published in open energy industry literature, with more publications to follow.

Jan 1, 1981

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines" in various foreign countries. In the preparation of this interpretation of the laws of Norway, use has been made of William R. Orrmins' translations of various acts of the Norwegian Government, which were forwarded from the American consulate at Oslo^ and transmitted to the Bureau of Mines through the courtesy of the State Department. This digest is released subject to amplification and correction, if necessary, by the proper American foreignservice officers.

Nov 1, 1932

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District&apos;s Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee&apos;s central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project&apos;s geotechnical report are addressed.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District&apos;s Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee&apos;s central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project&apos;s geotechnical report are addressed.

Jan 1, 1991

By C. F. Chung, F. P. Agterberg

"Prediction of a variable sulphur content in Cape Breton seams is important for planning the production of a highgrade metallurgical coal. Two extrapolation methods (Kriging and a version of Universal Kriging) to predict sulphur content in blocks of coal before mining are presented and applied to the New Lingan Mine reserves in the Harbour seam. The uncertainty of the predicted values is expressed by using standard deviations. Some statistical results for the Phalen seam, which occurs about 400 ft below the Harbour seam, are presented for comparison. The two mathematical models consist of two sets of equations which have been used in computer algorithms. Some limitations of the present approach and possibilities for further statistical work are indicated."

Jan 1, 1973