Search Documents

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By R. W. M. Lai

INTRODUCTION Manganese nodules were first discovered by the H.M.S. CHALLENGER expedition of 1873-76 and have engaged the interest of oceanographers and natural resources engineers ever since (1-4). Manganese nodules, some of them as large as grapefruit, cover vast stretches of the ocean floor throughout many parts of the world. In some areas the ocean floor is literally paved with nodules. The Pacific Ocean alone is estimated to contain 1.5 trillion tons of nodules which are forming at the rate of about 10 million tons per year (2). An analysis of the principal metal values for Pacific Ocean nodules is shown in Table I (5). [ ] The principal ingredients of the nodules are manganese and iron, but they also contain other important associated metal values such as copper, nickel, cobalt, and molybdenum. These associated metal values,

Jan 1, 1980

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By Jerzy Matuszewski

Under conditions of high methane content in the seams and the descending of exploitation to greater depths, methane hazard control is becoming more and more difficult. This is due both to the amount of methane released and to the technical possibilities of diluting and capturing it. The removal of excess methane from mine workings only by means of the ventilating current has become a problem. Therefore many countries designate large sums of money for research work in the field of controlling dangerous methane accumulations and for introducing this control into mining practice. In Poland the Central Mining Institute is leading in this field. Its Safety-in-Mines Institute, Barbara Experimental Mine in cooperation with collieries has recently carried out interesting investigations on the distribution of methane concentrations in gobs behind the front of longwalls mined with caving.

Jan 1, 1980

By Alec G. Richardson, S. H. Chiang, Ralph W. Lai, McMahan L. Gray

The potential of coal cleaning by selective agglomeration was examined for a Pittsburgh seam bituminous coal using isooctane as an agglomerating liquid. The effects of particle size, pH, degree of mixing, and dosage of isooctane on the pyrite and mineral matter removal from finely ground coals were investigated. The role of shear-enhanced-hydrophobic-association in the flocculation of fine particles was examined. The degree of liberation of pyrite from coal at different grinds was examined using an automated petrographic image analyzer. The effect of dispersant on slurry rheology during grinding was studied. The results indicate that over 95 percent of the pyritic sulfur can be removed from the coal. Final products containing less than 0.9 percent ash at a combustible recovery in excess of 90 percent have been obtained with multiple stages of cleaning.

Jan 1, 1989

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Trixie mine is located in the East Tintic Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1984

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

Chief Geologist, Groundwater and Engineering Geology Branch South Australian Department of Mines and Energy The six papers submitted for consideration during this session include two dealing with techniques for measing rock mass behaviour, including permeability, in boreholes, one describing the use of surface geophysical methods to delineate pollution plumes in groundwater together with analytical modelling of the plume, and one presenting a biological tracer technique applied to the determination of the origin of water entering underground mine workings. A paper describing dewatering at a base metal mine in Queensland includes an account of the investigation techniques employed to establish a conceptual model as a basis for the evaluation of various dewatering strategies. Of considerable interest is the use of a field gravity survey to delineate a zone of highly weathered rock which forms the major aquifer at the site.

Jan 1, 1988

By R. L. Tobie, E. K. Staley

Because of high production demands at San Manuel mine (approximately 40,000 tpd) and the relatively narrow grade range of the orebody, no attempt is made by the company to mine selectively. The caving sequence is laid out to meet the production demands, and proceeds in a manner to induce the least amount of weight on extraction openings. Once an area is undercut, draw control procedures are applied uniformly until the area has been mined to depletion. The orebody, located 50 miles northeast of Tucsoil, Ariz., is a low-grade deposit of chalcopyrite disseminated throughout a structurally weak, highly fractured, strongly altered granitic host rock over- lain by several hundred feet of relatively competent andesitic conglomerate. When undercut, the granite ore caves readily into fragments which usually pass through the grizzly without either excessive breaking or an undue amount of secondary blasting.

Jan 6, 1967

By G. T. Adel

As a prerequisite to removing mineral matter from coal by any physical separation technique, the mineral and coal particles must be sufficiently liberated. In the case of the production of superclean (< 2% ash), low-sulfur products, the appropriate liberation size may be less than 10 µm. Unfortunately, much of the liberation data obtained at these fine sizes is only qualitative due to the lack of appropriate instrumentation. In the present work, computerized image analysis has been used to characterize several common eastern U.S. coals. In most cases, it has been found that micronizing of the coal is necessary in order to achieve sufficient liberation for deep cleaning. Liberation analyses of the products from the microbubble column flotation process have been used to distinguish problems in liberation from problems in selectivity, especially as they pertain to pyrite rejection.

Jan 1, 1989

Many organisations, including those in the resources industry have Board-level endorsed principles on sustainability. A key challenge, however, is how to systematically integrate these high-level principles into the design and operation of mineral processing plants. In an effort to meet this challenge the Sustainable Operations framework, called SUSOP®, was conceived and developed through the Corporative Research Centre for Sustainable Resource Processing (CSRP) in Australia. Somewhat analogous to HAZOP (Hazard and Operability Studies) which is well entrenched in the resources industry, the key aim of SUSOP® is to produce a holistic, systematic and rigorous methodology for identifying and assessing sustainability opportunities and risks. This paper argues the need for such a sustainability framework, presents the key elements of SUSOP®, highlights how case studies enhanced its development and articulates the reasons why such a framework will have growing importance into the future.

Jan 1, 2011

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982

By Chester O. Ensign

Results of the application of geologic knowledge to grade control have been remarkable. Grade reduction from dilution has been diminished from greater than 9% at the time of the program&apos;s beginning to about 2% at present. This has resulted in an increase of about 1.8 lb of copper per ton of ore mined and has made a substantial contribution to earnings at White Pine during the past two years. Even more improvement is expected in the future. The White Pine orebody, situated in the southwestern portion of the Keweenaw peninsula of upper Michigan, is a gently dipping stratiform or bedded deposit. Copper distribution is stratigraphically controlled with higher values being confined to specific beds in the ore column. Room-and-pillar mining is practiced. Mining technique and geologic characteristics present a special array of problems in controlling the grade of ore.

Jan 4, 1964

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By John R. M. Hill, Gerald Zink, Fun-Den Wang

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed, small-hole drill has been fabricated and tested in the laboratory. High Priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure, high-speed swivel feeds water to the bit at about 4 L/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40-kW (30-hp) capacity. Results of recent full-scale laboratory testing (Now. 1977) are presented.

Jan 12, 1979

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003