Search Documents

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By Shichao Zhao, Ke Xie, Qijie Zhai, Wenbin Xia, Yuanyi Guo, Changjiang Song

"This paper investigated the structure evolution and phase formation ofFe-(11,13,15wt.%)Mn alloy under near-rapid solidification conditions. It is found that the area ratio of equiaxed zone in the Fe-13Mn alloy is the largest. And the primary dendrite arm spacing of Fe-(11,13,15wt.%)Mn alloy increased clearly with increasing distance from the surface. The volume percentage of HCP phase increased with increasing manganese content in the range from 11 pct to 15pct.IntroductionThe developing trend of automobile is the energy conservation, enviromnent protection, light weight, and high security. So the material would be required to the higher strength, higher plasticity and more likely to processing of automotive steel. Fe-Mn based alloys is considered as a potential material to the third generation automobile steel for its high damping performance [1], good mechanical properties [2-3], and high young's modulus [4]. And it is important that metastable HCP phases of Fe-Mn based alloys, which attracts technological interest for theoretical and experimental research [5-6].Metastable materials have been extensively used in the area of iron steels. Among various fabrication methods for high performance materials, rapid solidification is one of most popular ways to produce advanced materials by obtaining metastable phases. The solidification of metals in metastable phases provides access to an extended range of materials properties with novel properties [7]. Thus, in this work, Fe-Mn alloy metastable materials prepared by near rapid solidification is studied."

Jan 1, 2013

By M. E. Poad, Donald Ross, G. G. Wadell

Because of the "energy crisis" emphasis has been placed on bringing coal mines into full production faster. To accomplish this, more is involved than a rapid excavation system. Mine design should have the freedom within the law to customize as mining conditions dictate as long as the maximum safety of the miner is insured. A year ago, safety was the most prominent "social-human factor"--now, safety and energy self-sufficiency are primary to our national policy. The Single Entry research program as designed satisfies both. It investigates the hypothesis that a single-entry system, for longwall development, supported in the center by open cribs and divided by a fire-resistant partition, can be regarded as being equivalent to or better than a multi-entry system. This paper provides an explanation for the use and advantages of a single entry system in development for longwall mining, explains the problems anticipated with single entries and presents the research approach needed to evaluate and solve the problems. Under study are ground control, ventilation, fire and explosions, emergency procedures, and industrial hazards. Described are measurements data on crib and roof bolt loads as entry heading advances and longwall abutment load is superimposed, stress field determinations and preliminary structural analysis of the double and single entry, and methane liberation and ventilation records as entry advances. Some of the mine operation problems and waivers of mining laws will be discussed. This project is a complete system study having progressed approximately two years in a five-year program.

Jan 1, 1974

By D. J. McCracken

The lithium review did not arrive in time for publication in the June issue The estimated consumption of lithium minerals as raw materials to the glass, ceramic and metallurgical industries in 1992 was 85.5 kt (94,200 st). That equates to about 12 kt (13,200 st) of lithium carbonate equivalent (LCE). An additional 150 kt to 200 kt (165,000 to 220,000 st), or 7.5 kt to 10 kt (8200 to 1100 st LCE), were used in the production of lithium chemicals. The 1992 consumption represents an overall decrease of 3.5 kt (3800 st), or 500 t (550 st) LCE, from 1991. This was a direct result of a worldwide reduction in glass demand due to the economic recession. There are three major producers of lithium minerals. Gwalia Consolidated Ltd. (formerly Lithium Australia Ltd.) in Western Australia and Tantalum Mining Corp. (Tanco) in Manitoba, Canada, both produce spodumene ore. Bikita Minerals, in Zimbabwe, is the largest producer of petalite. Bikita also has the capacity to produce small volumes of spodumene concentrate. The Cyprus Foote spodumene operation at Kings Mountain, NC, ceased production in 1992. It once produced about 2 kt/a (2200 stpy) of "high iron spodumene" for uses other than in the manufacture of lithium chemicals. The lithium products of the major producers are shown in Table 1. The current resources of 13 Mt (14.3 million st) of LCE in the western world will supply demand for more than 50 years.

Jan 1, 1993

Advances in extractive metallurgy, 1977. Proceedings of the third symposium organised by the Institution of Mining and Metallurgy held from 18-20th April 1977. London, the Institution of Mining and Metallurgy, 1977. 244 pp. £18,50. Coal preparation A meeting of the Organising Committee of the Eighth International Coal Preparation Congress took place in Moscow on 24th and 25th May, 1977. Representatives NIM reports Report no. 1906 An automated instrument for measuring the effects of impurities on cathodic-current efficiency during the electrowinning of zinc. (2nd Sep., 1977). Report no. 1908 An analysis of the replies to a questionnaire on materials of construction for ore hoppers. (16th Sep., 1977). Report no. 1913 The mechanism and rate of reduction of Mamatwan manganese-ore fines by carbon. (2nd Sep., 1977). Report no. 1914 The thermodynamics of the formation of sulphate complexes of iron (111), cobalt (11), iron (11), manganese (11), and copper (11) in perchlorate medium. (15th Sep., 1977). Report no. 1924 The composition of chromite grains from varwUB Witwatersrand reefs. (23rd Sep., 1977). Atomic absorption The Perkin-Elmer Corporation of South Africa is planning to hold an Atomic Absorption Autumn School in Cape Town from 10th to 13th April, 1978. Travel bursaries Two Atlas Cop co travel bursaries for study tours of Swedish mines may be awarded annually to young mining graduates. Stability in coal mining The First International Symposium on the above subject is to be held in Vancouver (Canada) on 5th to 7th April, 1978.

Jan 1, 1978

By W. H. Ode, F. H. Gibson, W. A. Selvig

The great expansion of production of aluminum for war purposes has aroused some concern regarding the available supply of carbon suitable for making carbon electrodes required in the electrolytic aluminum process. Approximately three-quarters of a pound of carbon electrode is consumed for each pound of aluminum produced. 5 Because of its small amount of impurities and its suitable physical characteristics, calcined petroleum coke is the standard material used by the aluminum industry for making electrodes As it may be necessary to use some substitute materials, the possibility of using coke made from coal has been considered. Besides this possible use, information concerning the source of low-ash coals is of general interest. Specifications of the aluminum industry for calcined petroleum coke suitable for the manufacture of electrodes are very stringent in regard to allowable impurities. In one such specification the maximum allowable ash is 1.0 percent; the maximum allowable content of iron (as Fe) is 0.06 percent and that of silicon (as Si) is 0.08 percent; the maximum for cal- cium (as Ca) and for sodium (as Na) is 0.12 percent for each, but the two combined may not exceed 0.12 percent; maximum allowable sulfur is 2.0 per- cent. The presence of barium, nickel, chromium, manganese, cobalt, or vanadium is objectionable, and only extremely small amounts are allowed. In regard to physical properties, the coke is required to be so thoroughly calcined that it has a real density of at least 2.02.

Nov 1, 1943

By James J. Bryja, Thomas M. Barczak, Dennis R. Dolinar, Joe Bower, Thomas P. Mucha

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial and error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground, reaction behavior based on the support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health (MOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate -- application of alternative roof support systems or to design in- mine trials such that a fair and equitable comparison of different support systems can be made. A case study if the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to conventional wood and concrete cribbing historically used at this particular mine.

By Helmer Kraemer

One of the CIM 2003 conference themes is ?Globalization and the impact on mine operations?. In this context, the first official version of the new ?International Rock Excavation Data Exchange Standard? (IREDES) is being released. This new standard is a highly flexible data interface for exchange of information between production equipment and central computer systems. The standard was defined by global players in the mining industry and will soon be used to enhance local operations of global mining companies. Beside the standard definition now other aspects are coming into focus: The question how to design and how to implement IREDES compliant data exchange in practice. Implementation of IREDES covers the following aspects: !" Implementation on in-field production systems !" Communication and networking !" Implementation on databases and commercial IT systems In-field production systems are characterized by a big variety of different automation systems. Therefor, different IREDES implementation philosophies have to apply to those systems. One philosophy uses an integrated IREDES compliant automation system on every machine. The alternative method uses one shared IREDES compliant ?Proxy server? for a number of machines connected to this server using proprietary interfaces. Communication and networking can be integrated openly and independently from hardware infrastructures. The only precondition is that communication and networking has to be Ethernet - TCP/IP protocol compatible. IREDES Implementation on the commercial IT level means to exchange IREDES data sets with databases, simulation software, office packages and special applications. Interfacing is easy as long as the software or the database system provides an interface to the Extensible Markup Language (XML).

May 1, 2003

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

Scientific drilling and blasting techniques are currently being presented to the mining industry as an aid in the overall optimisation process. The degree of success in the development of these techniques over the last ten years has prompted statements that generally relate to blasting becoming a science rather than an art. Many of the techniques are currently operated or at least analysed by scientists. As such, their use has been restricted to project type activities while the more routine activities associated with day to day mining has continued to be carried out by engineering rather than scientific staff. Some of the scientific techniques will remain legitimately as a project or an occasional use facility. Generally speaking a cost/benefit analysis at a particular mine will decide the level of use. This should logically highlight a number of techniques with potential of regular mine site use. Regular mine site use implies mine site analysis and hence the gulf between the scientist and mine operator/engineer must be addressed. There are all sorts of solutions and they are not mutually exclusive. One alternative could be to increase specialisation at the mines. With "career paths" becoming more formalised the trend would seem to be away from mine site specialists unless, for instance, this specialisation was provided by term secondment from research establishments. Another alternative could be the scientists themselves applying their developmental skills to "humanise" and "package" the projects in such a manner that they can be routinely used at mines.

Jan 1, 1990

CORPORAL SHEPPARD B. GORDY Sheppard B. Gordy, a brief biography of whom was printed inn the January Bulletin, entered the employ of the Braden Copper Co. immediately on his graduation from the Sheffield Scientific School in 1912. He remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with CORPORAL SHEPPARD B. GORDY. the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time lie had gone to Dayton, Ohio; to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9.

Jan 3, 1919

By James J. Brady

The basic story at Bear Swamp was how to excavate an underground chamber 79 feet wide by 227 feet long and 150 feet high, along with the related access, tarbrace, leads, power tunnels and shafts, do it under cost and ahead of schedule and still have just about everybody love you. The isometric sketch of the overall project follows. I won't go into any of the details of the physical scope at this point. Instead, we'll bring out the sizes, grades, particular problems of the different areas as we cover them. First of all, let's establish that Bear Swamp was a Target Estimate - Fee with Incentives type of contract. Gates and Fox's contract was with the project's general contractor, J. A. Jones. We were one of three contractors who submitted proposals and estimates to Jones. After much negotiation and many submittals, Gates and Fox was notified we had been selected to do the underground excavation on April 12, 1971. We had our first people back on site in two days, set up a temporary office, made our first steel order for jumbo erection, pacing our jumbo construction to meet the date when J. A. Jones would have the access portal ready for us. The shops, yards, dry house, compressor building were all erected as sites were designated for our use. At last, on Thursday, June 3, we trimmed the face and moved our 9-machine Euclid jumbo up a hastily constructed haul road and started our portal preparation of the access tunnel.

Jan 1, 1974

By Robert C. Meaders, Arthur R. MacPherson

Many attempts have been made to eliminate most of the crushing plant and all the grinding plant in the process of ore beneficiation by substituting a combined crushing and grinding unit which could take coarsely crushed ore and reduce it to a fine size in one unit. This unit normally would have no other grinding media than the ore itself. This is true autogenous grinding, as we understand it today, and should be clearly distinguished from pebble mill grinding, where pebbles are substituted for steel balls to grind a ball mill size feed. To compete in efficiency with normal methods of crushing and grinding, the autogenous mill must use less labor and steel to produce an equivalent product at equal or lower power consumption. In general terms, a unit to perform these functions must have means to crush the ore to fine sizes and to then further reduce the crushed pieces by grinding. In other words, to do efficient autogenous grinding, there must be a proper balance established between crushing and grinding rates. There is not much point in crushing at too fast a rate if the grinding means are not present to reduce the small particles to the required product size. The crushing means used in an autogenous mill are impact forces of two kinds, namely, (1) the rock travelling at high speeds striking the shell, and (2) the lifters travelling at high speeds striking the rock. Grinding is probably effected in a manner equivalent to pebble milling.

Jan 9, 1964

By Murray D. Fredlund

The consolidation of soil material is central to many types of engineering analysis. Problems such as the building of highway structures, landfills, or buildings over saturated soft clays require application of such theory. It has been found in industry that the application of consolidation theory has lagged significantly behind the theory which has been developed some time ago. The application of small-strain saturated consolidation theory was first proposed in a 1D form by Terzaghi. Although this theory has been available for some time it?s implementation into software packages in 2D and 3D forms has been slow due to inherent complexities in the coupling equations. The flow and stress equations are also inherently somewhat unstable and this further complicates software implementation. Of particular interest in the mining industry is the consolidation of uranium tailings. One such disposal method that has been utilized is the subaqueous deposition of uranium tailings in large pit structures. When performing such deposition the calculation of consolidation rates is central to determining final pit capacity and expected life. Consolidation software can be successfully used in such cases in order to determine pit filling rates. The primary complexity, however, is that tailings are typically deposited in slurry form and therefore the potential deformations are large. Large-strain consolidation theory is therefore required in order to properly solve the deformations over time. This paper presents the use of a large-strain consolidation analysis in order to predict long-term filling rates in a uranium tailings pit.

Aug 1, 2010

By Asfahani. Jamal, Randa Mohamad

"Abstract - Electrical and structural characteristics of formations favorable for sulfur occurrences in northeast Syria are described using geo-electrical prospecting methods. Simple (VES) and combined (CVES) Schlumberger vertical electrical soundings and geo-electrical profiling using a Wenner configuration were applied to the Teshreen structure. Six profiles (A, B, C, D, E, and F) at the borders of anticlines, where positive and negative structures are joined and salt formations have a tendency to disappear, were studied.Secondary structures, characterized by high apparent resistivity exceeding 3000 Ohm.m were located on each profile using a Wenner profiling configuration. These secondary structures are demonstrated to be favorable for sulfur prospecting by both drilled wells and vertical electrical soundings. Traditional interpretation of the 84 VES measurments is supported by data from 14 CVES measurments. The CVES technique is a powerful tool, due to its improved resolution of the electrical boundaries.Thicknesses and resistivities of the Lower Al-Fares, Al-Garibeh, and Al-Dibbaneh formations were determined through the interpretation of VES measurments. The same VES measurments were then interpreted using the Pichgin method, whereby all the subsurface tectonic features were determined for depth penetration corresponding to AB/2 = 1000 m. The integration of the first and second VES phases creates a clear picture of the subsurface, including tectonic, geometric, and geoelectrical information. In summary, the sulfur occurrences in the research area are controlled by tectonic paths that are well defined by geo-electrical methods. These diverse geo-electrical methods could be used successfully for sulfur prospecting in similar environments."

Jan 1, 2002

By P. W. A. Walker

"The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.216% W03 and 0.020070 Mo. The deposit is uneconomic at current tungsten prices. IntroductionDuring the 19705, Union Carbide Corporation was a major producer, processor and supplier of tungsten and derivative products to end-user manufacturing industries. The corporation owned and operated two tungsten mines in the United States, and one in Brazil, and operated a plant in the United States which produced ammonium paratungstate (APT) which is an intermediate product in the production of tungsten wire and tungsten carbide for cutting tool insets and hard facings. In 1975 the three mines were ageing with short-life reserves and high production costs. The world market for tungsten was buoyant and prices, in constant dollar terms, had risen steadily over the past 15 years (Fig. 1).It was against this background that a decision was made to explore for tungsten in North America, South Mrica, Australia and Brazil."

Jan 1, 1994

By John Chipman, Daniel Dutilloy

The equilibrium of gaseolis H2O-H2 mixtures with liquid iron-phosphorus alloys in the range 0 to 3 pct P is used to establish the increuse of the activity coefficient of oxygen, in the presence of phosphorus. Two different sampling techniques are used. THE importance of oxygen as a refining agent in steelmaking operations makes it desirable to improve our understanding of its behavior. Phosphorus which is always present in the ores has adverse effects on steel properties and its removal is necessary. The present study was undertaken to evaluate the interaction of oxygen and phosphorus in molten iron. Bookey, Richardson, and welch1 have studied the phosphorus-oxygen equilibria in liquid iron in the presence of lime. They used a mixture of hydrogen and water vapor to control the oxygen potential and worked with crucibles made of tetracalcium phosphate and lime. At low phosphorus concentration, i.e., at high oxygen, they observed a marked deviation in their results. They tentatively ascribed this to a large negative effect of oxygen on the activity of phosphorus. This was then included by chipman2 in his review of interactions in liquid iron. Pearson and Turkdogan 3 have later reported an interaction parameter They equilibrated a mixture of hydrogen and water vapor with an iron-phosphorus alloy contained in an alumina crucible and sampled the melt by suction in a silica tube. The solubility of oxygen in iron-phosphorus alloys has been studied by Levenets and Samarin.4 They reported an interaction parameter

Jan 1, 1961

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961