Search Documents

By B. G. Bunting, J. H. Johnson, H. J. Schock

This paper describes an experimental method for monitoring diesel-generated exhaust gas pollutants in a deadended drift to assess the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 32 m long and slightly downsloping, with an everage height and width of 2.4 and 8.6 m, respectively. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generate pollutants. Induction ventilation appeared to be the least effective of the three methods examined.

Jan 1, 1982

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By Theodore H. Eyde

The Superior Oil Co. drilled two holes, 4720 and 5940 ft, respectively, using conventional oilfield rotary drilling equipment. The results indicated that large rotary drills can be adapted to mineral exploration purposes with few modifications. The principal advantages are: a large hole diameter, excellent samples of cuttings, a geolograph which is a constant drilling record, rapid penetration even in hard rocks, and the ability to use electric logs for measuring the properties of the rock being penetrated. The disadvantages are the high cost of mobilization, drilling, and oilfield service at remote locations. Though the oilfield sampling techniques are adequate for identifying lithology, improvements are necessary to obtain representative samples for analytical purposes. As deeper targets are explored, mineral exploration organizations will have to resort to rotary drilling.

Jan 1, 1975

By Kenneth L. Clifford, Thomas G. White

Many changes have occurred in lead-zinc milling in the U.S. since the 1970 Lead and Zinc Symposium. New mills have been built, novel flowsheets devised, and the use of process control techniques is increasing. The Missouri concentrators produced in 1976 more lead and zinc concentrate than those in any other state. The Tennessee mills produced nearly as much zinc concentrate in 1976 as Missouri and with some very highly developed flowsheets. Progress in the Western U.S. is centered around new operations in Colorado and Utah. New mills in New York and Missouri incorporate many of the newer control concepts. Most of the older concentrators have undergone flowsheet changes to accomodate different ore types or because of the availability of new and better equipment.

Jan 1, 1977

Utah Development Company operates a mine at Blackwater with a present annual production of 4 000 000 tonnes of coking coal. Mineable seams outcropping on the company's lease are part of the Permian Mammoth Rangal Coal Measures. Current operations are based pre- dominantly on the Main Lower seam. Coal quality variations occur along the seam strike, in the direction of seam dip, within the seam plies and in isolated anomalous areas. Raw coal of non-specification quality is washed to reduce ash and sulphur and to improve the free swelling index. Raw coal meeting specification quality is sent directly to product, by-passing the washplant. Careful attention to mining, coal preparation and product blending is necessary to ensure that the combined product meets specifications.

Jan 1, 1974

By Kikuo Matsui

In a difficult economic environment, the coal mines in Japan have been making extensive efforts in order to survive by rationalizing the mining operations. Introduction of a new longwall mining system is one of these efforts to establish the rational production structure. In the high production longwall mining system, gateroads should be developed rapidly and maintained effectively during their lifetime. Strata bolting support system has been employed in the gateroads to raise their stability levels and reduce their maintenance cost. However, excessive gatemad closure caused by longwall mining is still occurring, impeding the passage of equipment, personnel transportation, and ventilation air in the longwall panels. This paper describes the development system of gateroads and proposes a new mining method to control the excessive roadway closure problem.

Jan 1, 1995

By Toguri JM

A solid electrolyte technique has been used to measure the activity of cobalt in liquid cobalt-gold alloys containing between 0.085 and 0.50 mole fraction of cobalt, and for temperatures from just above the liquidus to around 1550 K. The system exhibits positive deviation from ideality, both in the activities of cobalt and gold, and in the enthalpy and excess entropy of mixing. The results agree with previous measurements using a Knudsen cell - mass spectrometer technique, but differ from those reported for a gas equilibration method. The data have been used to calculate the activity coefficient of cobalt oxide in silica saturated iron silicate slags and to express the solubility of cobalt in such slags as a function of cobalt activity and oxygen pressure.

Jan 1, 1984

By William Price

DURING the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce risers of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1.

Jan 1, 1937

By W. M. McKewan

Dense magnetite pellets were reduced in hydrogen-water vapor-nitrogen mixtures over a temperature range of 400° to 500° C at a pressure of 0.97 atm. The rate of reduction per unit area was found to be constant with time and directly proportional to the partial pressure of hydrogen at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. THE investigation of the reduction of iron oxides has been the subject of numerous papers. Most of these papers have dealt with the evaluation of various ores, both magnetite and hematite. There have

Jan 1, 1962

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

By E. A. Lucero, H. E. Robbins, T. H. Dudley

EL Salvador mine of Andes Copper Mining Co., E subsidiary of Anaconda Co., is in northern Chile about 18 miles north of Potrerillos, 7825 ft above sea level. Initial production is planned for the first half of 1959. Plant capacity will be 30,000 tpd, and there are 308,835,000 tons of proven ore reserves, averaging 1.49 pct Cu. The Inca adit is being driven as part of the mine-to-mill haulageway. Because of the overburden it is planned to mine the deposit by block caving. Ore will be dropped from upper gathering levels through ore passes to the Inca adit, through which it will be transported out of the mine to the primary crushing plant located a half mile from the portal.

Jan 3, 1958

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Payne P, Beirne W, Geldard D, O&apos

Whim Creek Consolidated N.L. has operated openpit mines at Meekatharra since 1980. Mining operations commenced with the Haveluck openpit and the Phar Lap openpit was started in 1 984. Grade control in the Haveluck mine was simple because the orebody showed good continuity along strike and down dip and had an easily recognisable hanging wall contact. Problems were encountered once mining corn menced at Phar Lap because of the complex lithologies, alteration and faulting involved. Simple grade control techniques developed for Haveluck failed and were not solved until an understanding of the ore bodies was achieved.The integration of all geological data into the interpretation of the developmentdrilling results has proved essential to achieve effective grade control atreasonable cost.

Jan 1, 1986

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By Stewart W. J

The volumetric method of estimating hydrocarbon resources and recoverable reserves is and probably will remain a dominant method in petroleum engineering. The method is technically very simple, but has one main problem: how to express, measure and properly handle the variable and complex uncertainty of each estimate. The computer age brought in the Monte Carlo Simulation method which enables correct arithmetic operation using data with specified probability distribution. However, several problems are still not solved uniquely and still exist. For instance, the determination and description of the distribution of single parameters, the determination of the degree of dependency between parameters (e.g. hydrocarbon saturation-porosity), and standard probabilist- ic definition of generally used categories (e.g. proved, probable, possible). Methods for handling these problems are discussed.

Jan 1, 1979

By Howard E. Parkinson

The mine pager phone to public telephone interconnect system permits mine paging telephones to be interconnected with the public phone system, thereby providing emergency and off-hours communications. The system, a push-to-talk, push-to-listen system, is compatible with any mine paging system utilizing dc voltage on the line to enable paging. A tone generator of the proper frequency enables an outside caller to page over mine pager system loudspeakers. A caller inside the mine can make an outgoing call to a preselected, preprogramed number with the use of a proper frequency tone generator. The system includes an automatic hangup timer that restricts the time off-line due to a wrong number or incorrect hangup to 20 seconds and 6 minutes, respectively.

Jan 1, 1974

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

By L. E. Schultze

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines devised a processing sequence for recovering uranium from carbonaceous ores. Uranium extractions of 97 pct were obtained by contacting the ore with a solution containing 400 grams of ferric sulfate hydrate in 200 ml water for 3 hr at boiling temperature (96° C). Uranium was recovered from the leaching solution by solvent extraction with tri-issooctyl amine. The barren ferric sulfate solution was recycled to the leaching system. The leaching process resulted in no detectable dissolution of carbonaceous material from the ore. Work on the project was terminated in 1978 because of a transfer of responsibility to the U.S. Department of Energy.

Jan 1, 1981