Search Documents

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By Marvin P. Barnes

An attempt has been made to compile and code geologic data relating to twenty of the major porphyry copper districts of North America in such a manner as to permit the use of modern electronic digital computers to retrieve, compare, and build statistical mathematical models from the input. In the exploration process as part of his broader efforts to evaluate the potential of some prospective region, district, or ore body, the experienced geologist consciously or subconsciously compares and fits the observed geologic features to similar phenomena associated with known ore bodies with which he is acquainted. Thus an adequate conceptual "model" of the total geologic environment and type of ore body sought is an essential requirement for the successful exploration effort. Numerous such models of porphyry coppers already exist in the minds and notes of many experienced geologists today. These models are, of necessity, couched largely in qualitative terms and though they may be quite definite in the mind of the porphyry copper expert, the total concept of what constitutes a porphyry copper deposit and environment is difficult to convey in very precise terms. There probably is no such thing as a typical porphyry copper deposit. However, it is well understood that most of the deposits that have been studied have many geological characteristics in common. A logical question then might be: What characteristics are most common or how often do they occur in common, and what is their relationship to other common characteristics ?

Jan 1, 1970

By B. J. Zhang

Conventional spirals are capable of providing excellent clean coal recovery, although at a relatively high ash content. Compound spirals, which provide two stages of spiral cleaning in a single taller unit, have been commercialized in recent years to improve upon the cleaning performance obtained from conventional spirals. The present study aimed at optimizing the performance obtained from a compound spiral for cleaning especially high sulfur fine and ultrafine coal. Industrial-scale spiral units were utilized for this study in a pilot-scale facility at the Illinois Coal Development Park. A statistically designed experimental program was conducted to optimize ash and sulfur cleaning performance of the compound spiral. It was found that significant cleaning of ultrafine coal (i.e., 150 microns × 45 microns and even 45 microns × 25 microns size coal) is achievable with the compound spiral. However, operating conditions for cleaning finer coal fractions (-150 microns size coal) have to be significantly different from those used to clean coarser coal fractions (+150 microns size coal). The sulfur rejection trends were different from ash separation efficiency trends in all size fractions except 45 microns × 25 microns. The probable error (Ep) and effective specific gravity of separation (SG50c) determined for the compound spiral cleaning of the overall particle size were as low as 0.07 and 1.62, respectively. However, the bypass of a small percentage of clean coal to the tailings stream of the compound spiral, may need further adjustment of the key process parameters.

Jan 1, 2014

By Gus L. Maciula

Although I will briefly review the current status of coal slurry pipeline technology, I wish to make it clear that this is not a technical paper. It is intended instead to review the current situation on energy resources and requirements, and the environmental, political and economic considerations that mandate a serious consideration of Slurry pipelines as a viable mode of coal transportation into the Georgia and Florida markets. In order to more fully appreciate our current energy situation, it will be helpful to go back a few years and review the evolution of our so-called energy "problem." It was about two decades ago that the first and only major natural gas transmission pipeline was built into the State of Florida by Florida Gas Company. This line was conceived and implemented during a time when gas was plentiful and cheap, and it appeared at that time that unlimited gas reserves were continually being discovered, thus assuring the availability of a clean, cheap fuel and the ,viability of the pipeline system. One of the major factors justifying the original pipeline construction as well as subsequent expansions was a series of long-term commitments under which Florida Gas transported natural gas owned by electric utilities for use as boiler fuel. Thus for the past 20 years Florida industry, commerce, and domestic fuel requirements have been met either directly or indirectly through clean, cheap natural gas which would not have been otherwise available without the pipeline system.

Jan 1, 1978

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By S. C. W. de Jong, E. de Hoog, J. M. van Wijk, S. J. Dasselaar

Introduction Technology development for sustainable, safe, reliable and efficient mining of polymetallic nodules in the deep seas requires careful design, thorough understanding and integrated testing of all equipment, physical processes and (sub) systems involved (Dasselaar et al [1]). Proceeding from Vertical Transport System (VTS) experiments at IHC laboratory scale by Van Wijk [2], with typical system dimensions of several meters, to prototype or pilot scale testing with typical dimensions of several kilometers, is a giant leap. Naturally, intermediate steps are required in order to mitigate the possible risks in the full-scale system’s (physical) processes. Within the EU program Blue Mining (2014-2018), possibilities emerged for performing experiments at intermediate scale: the so-called medium-scale vertical slurry experiments. Near Freiberg, Germany, the village Halsbrücke possesses a 140 meter deep empty vertical mine shaft, perfectly suited for housing the test setup. For this purpose, a 318 meter long 145 mm pipeline circuit was constructed, including both a 130 meter high vertical riser and fall pipe section. A purpose-built sediment injection and separation system was deployed, including a 55 kW centrifugal pump. The riser section has been equipped with sensors capturing pressure, temperature, flow velocity, volumetric concentration and flow visualization. The planning, modification and construction of the test facility site itself is described by Müller et al [3]. The present paper describes the objectives, experimental program, equipment, and the preliminary results. Publications on in-depth results are foreseen in the (near) future.

Jan 1, 2018

By Jr. Garnar

Heavy mineral mining has been a relatively small but important Florida industry for over sixty years. Geology of the Florida heavy mineral deposits is similar. Each formed along active coastlines after which the titanium minerals were upgraded in TiO2 by post depositional oxidation and leaching of the iron. There are four heavy mineral plants currently Operating in Florida. Ore is mined by dredges and the heavy minerals concentrated by gravity separation. The heavy mineral concentrates are further processed with high tension and electromagnetic separators to Produce titanium mineral concentrates for TiO2 pigment manufacturing plants. Zircon sand is produced as a co-product at all of the Florida plants. Staurolite is produced by Du Pont and Titanium Enterprises. Du Pont also markets a kyanite-sillimanite product. (Monazite is produced by Humphreys and Titanium Enterprises). Reclamation of mined-out land is an important part of heavy mineral mining. At the Du Pont plants soil is removed ahead of the dredge and placed over the quartz sand tailings. Grass is planted after fertilizing. A year later the land is fertilized again and pine trees planted. Most of the heavy mineral deposits now being mined will be nearly exhausted by the end of the century. New deposits to be mined in the 21st century will probably be smaller and lower grade than those now being mined. Advances in mineral processing technology will have to be made to allow these lower grade deposits to be mined economically.

Jan 1, 1978

By Debbie Marshall

Nickel and cobalt in lateritic ores can be extracted by either a hydrometallurgical or a pyrometallurgical route. The high-iron limonitic fraction of a deposit is best processed' hydrometallurgically while the magnesium-rich transitional and saprolitic fractions are more suited for pyrometallurgical processing. During hydrometallurgical processing, it may be attractive, for economic reasons, to blend the limonitic component with transitional and saprolitic ores, which contain higher nickel levels. However, blending increases the concentration of magnesium in the feed, leading to increased acid demands. The decision on how much ore to process then becomes an economic one. Ore samples with different magnesium contents were prepared for the leach test program by blending limonitic and transitional ores. The ore samples were slurried in seawater and tested in the Falconbridge Hydrometallurgical Pilot Plant. As expected, acid consumption increased with increasing magnesium content of the ore. For target extractions of 95% nickel and 92% cobalt, the required residual free acid concentration increased from 30 g/L at 1.7% magnesium to 50 g/L at 2.7% magnesium. When the magnesium content was raised to 3.8% and 4.6% in subsequent pilot plant testing, the final free acid requirements did not increase beyond what was observed at 2.7% magnesium. Thus, the cut-off ore composition to maximize nickel units and minimize acid requirements is between 1.7- 2.7% magnesium. Keywords: high pressure acid leaching, laterites, magnesium

Jan 1, 2004

By Don M. Coulter

"INTRODUCTION The district comprising Union, Lafayette, Pontotoc and Calhoun Counties, Miss. (fig. 1), was examined in October 1941 by R. W. Smith of the Bureau of Mines, accompanied by J. W. Adams of the Mississippi Bauxite Co. 3/ Subsequently, geologists of the Federal Geological Survey made a more detailed study of the area. 4/Bauxite had been reported as present in several localities in Pontot. County, and large deposits of kaolin are known in Pontotoc, Union, Calhoun, and Lafayette Counties. Many of the bauxite deposits, such as those on Big Hill, Second Hill, and Third Hill, in Pontotoc County, form the caps on hills and are outliers of Wilcox deposits on the Midway formation. Such deposits could have no extensions because of erosion and were not examined, as they were investigated by the Mississippi Geological Survey. 5/ Most of the bauxite was known to be low-grade, with a high iron content. However, Pontotoc County in particular presented possibilities of finding high-grade bauxite with a low iron content by drilling down the dip from the Wilcox-Midway contact. Consequently, with few exceptions the investigation was confined to drilling in this direction.Headquarters were established in Tupelo, Miss., on July 13, 1943, and mineral agreements were obtained covering 8,367 acres of land, with 62 land-owners in Pontotoc and Union Counties. Holes were drilled on properties of three of the landowners in Union County and 36 in Pontotoc County."

Apr 1, 1948

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By John E. Riddell

This review is based on a questionnaire sent out to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geochemical techniques in Precambrian terrains. Of the companies questioned, 16 returned completed questionnaires and of these, ten companies stated that they had some experience in this type of work. Of the companies who did not answer or return the questionnaire in time I know that at least three have been quite heavily engaged in applied geochemical work in the glaciated Precambrian areas. I also know that these three companies have been reasonably successful in their ventures, so I feel the following figures and opinions are, if anything, on the pessimistic side. Before continuing with the paper I would like to express my personal thanks to the Chief Geologists, Geologists and Exploration Managers of the various companies who cooperated in making this review possible by answering the questionnaires and making available summaries of their work in the glaciated terrains. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only two have reported that they do not use applied geochemistry at all. Two companies have reported that they make use of applied geochemistry in New Brunswick in areas of-light glaciation. Their opinion is that it is a useful aid to other techniques in evaluating mineralized areas.

Jan 1, 1960

By A. W. Fahrenwald

"The rate of progress in the last three years in the development of differential flotation has been rapid beyond the realization of most people. Differential flotation is no longer a ""delicate"" and unreliable process, but is now in wide use. Its ""safety"" is due to the wide use of chemicals which either depress or enhance floatability by definite modification of surfaces.The extent of the development and reliability of differential flotation methods any be emphasized by pointing out that there are now several customall-flotation"" plants in this country treating complex lead-zinc-iron ores from widely separated mines. While these ores differ in chemical composition and apparently in physical nature, the various ores treated in such a plant are passed through the same crushing and grinding equipment and through the same flotation machines and flow sheet with only slight changes, if any, in quantity and kind of chemicals and oils added.Some of the development in differential flotation is due to intelligent research on the part of well-trained chemists and metallurgists; much of It must be attributed to empirical testing.Much of the success in differential flotation is due to more care being given to constant conditions with regard to such factors as (1) fineness of grinding, (2) density of pulp entering flotation machines, (3) quantity and constancy of oils and chemicals added to the pulp, and (4) place of addition of reagents, and time of ""conditioning"" treatment of pulp with reagents."

Aug 1, 1925

By M. V. Chari

A prime objective of physical coal cleaning is the separation of raw coal into a clean coal product with the required low ash and pyritic sulfur content and a high ash refuse. The refuse should also contain a minimum amount of combustible matter. In order to be effective, cleaning processes require that the mineral matter in the feed, including pyrite, be largely discrete and free particles, liberated so that the particles are not attached or embedded in coal. Liberation of mineral matter from coal, particularly pyrite, was investigated by Bechtel as part of two fine coal cleaning research programs sponsored by the Department Of Energy (DOE), Pittsburgh Energy Technology Center (PETC). Two proof-of-concept (POC) plants, each with a capacity of 900 kg per hour, were installed and tested to evaluate production of ultra-clean coal using microbubble flotation and spherical agglomeration technologies. The plants were designed to produce clean coal with 2 percent ash and pyrite content lower than that achievable by conventional methods. Also, the quality targets were to be attained at energy recoveries above 80 percent. Bench-scale flotation and agglomeration tests indicated that it would be practical to grind the 6 mm top size feed coal to a mean particle size (050) of 10 micrometers in the POC test plant. In this part of the paper, the steps taken in the grinding circuit to maximize liberation of mineral matter are described.

Jan 1, 1991

By S. J. Pearce

"INTRODUCTION AND SUMMARYComplaints have been made regarding dust respirators that may be used in coal-mining operations. Some of these complaints may be due to improper use of the respirator, inadequate knowledge of its purpose and mode of functioning, poor choice, poor fitting, or inadequate maintenance. It is hoped that this circular will answer these complaints by discussing the various factors relating to the proper use of dust respirators in general and in coal mines in particular.It is pointed out that dust respirators are not to be used as a substitute for dust-control measures. The construction, functioning, choice, fitting, and maintenance of dust respirators are discussed.FIELD OF USEThe function of the dust respirator is to prevent the wearer from inhaling harmful quantities of dust by removing dust from the air he inhales.A dust respirator is not to be used as a permanent substitute for dust-control measures. It is to be used as a temporary substitute until dust-control measures can be instituted or as a protective means where dust-control measures are impracticable, as in applying rock dust in bituminous-coal mines.The following sections of the ""Federal Mine Safety Code for Bituminous-Coal and Lignite Mines in the United States"" 2/ emphasize the fact that every effort should be made to keep the amount of dust in the air of the working places as small as possible:"

Mar 1, 1950

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By John S. Anderson

The need for fuels and minerals in this country is estimated to double, triple, or even quadruple by the end of the present century. Even assuming more recycling of scrap metals and some priority allocation of energy, as has been done, for instance in war time, the projected increase in the nation's population and ever-increasing wants of that population will require vastly more minerals than are now being produced. Since mineral ores are being mined at lower grades, and since all minerals, including fuels, are having to be mined from deeper deposits, the amount of surface land to be disturbed will, inevitably, be increased. We cannot depend on foreign sources to supply all the extra requirements, since the non-U.S. population is increasing, in most cases, faster than our own. Furthermore, starting from a lower base, their mineral needs may accelerate more rapidly than ours. Restrictions on exports may be applied in foreign countries, if it appears that remaining reserves are not sufficient to fill the national needs. In vice; of the opposition which the mineral industry is receiving, as has been well described at these sessions and elsewhere, what can we, as mineral producers, anticipate as regards our ability to continue to operate, to sway nothing of expanding production? Although not minimizing the problems involved, it seems obvious that, except under emergency conditions, the country cannot tolerate a reduction in the available

Jan 1, 1971

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994