Search Documents

By Richard A. Queeney, Lance G. Peterson

ESTIMATES of the stacking fault free energy of copper reported in the literature show an extensive divergence of results. Based on measurements of dislocation node radii, Thornton et al.7 find the lower limit of stacking fault energy to be 60 ergs per sq cm: Jossang and coworkers4 estimate the same value should be less than 40 ergs per sq cm. Assuming stacking fault free energy to be twice the coherent twin boundary free energy, Valenzuela8 reports 72 ergs per cm, while Inman and Khan2 cite a value of 24 ergs per sq cm. which can no doubt be accounted for by almost complete absence of interstitials in solution. However, the minute concentration was sufficient to permit observable recovery of dislocation damping. Assuming a dislocation density of 1010 CM -2 and an average loop length of 0.5 , a concentration of interstitials as low as 0.01 at. ppm is sufficient to reduce dislocation damping by more than a factor of ten. The concentration of interstitial solute atoms in Ferrovac E-0.15 pct Ti was thus estimated at 0.01 at. ppm < (C + N) < 2 at. ppm. The absence at elevated temperature of strengthening due to interstitials, Fig. 1, was therefore anticipated in the titanium alloy. The temperature dependence of the flow stress below 300°K was unaffected by addition of either titanium&apos; or zirconium.&apos; Observed, however, was an initial difference in the absolute value of the flow stress below 320oK, Fig. 1. Grain size may account for the difference; the grain diameter of Ferrovac E was 30 to 45 µ and that of Ferrovac E-0.15 pct Ti 65 to 90 µ. Although second phase particles in the form of titanium carbides and nitrides precipitated in the Ferrovac E-0.15 pct Ti alloy, the spacing was too large to produce any strengthening effect. The mechanical properties measured, therefore, were inherent to the bcc lattice. 1W. C. Leslie and R. J. Sober: Trans. ASm, 1967, vol. 60, pp. 99-111. 2 H. Conrad: Journal of Metals, 1964, vol. 16, pp. 582-88. 3 A. S. Keh and W. C. Leslie: Materials Science Research. H. H. Stadelmaier and W.W.Austin, eds., vol. 1.pp. 208.50, Plenum Press, New York, 1963. 4A. S. Keh, Y. Nakada, and W. C. Leslie: Dislocation Dymmics, Rosenfield, Hahn, Bement, Jr., and Jaffe, eds., pp. 381-406, McCraw-Hill Book Co., New York, 1968. &apos;W. J. Bratina, J. T. McCrath, and H. E. Rosinger: Can. Met. Quart., in press. 6 W. J. Bratina, J. T. McGrath, and D. Mills: Suppl. Trans. Japan Inst. Metals. 1968, vol. 9, pp. 436-43. &apos;H. E. Rosinger and C. B. Craig: Can. Met. Quart., In press. %. Mills. J. T. McGrath. and W. J. Bratina: ScriptaMet,, 1968, vol. 2, pp. 311-13. The purpose of this note is to present the results of a direct measurement of the stacking fault free energy in copper. The present method avoids both the question of interaction forces of nodal dislocations and the assumption that the coherent twin boundary free energy is one-half that of a stacking fault. Fig. 1 shows a transmission electron micrograph of a stacking fault intersecting a high angle grain boundary in copper: Fig. 2 is a schematic representation of the intersecting interfaces. To produce the specimen, pure copper was rolled to 0.002 in. thickness and annealed for several hours at 875°C. These foils were strained in tension to l04 µ in. per in., and rean-nealed to 8 min. Recrystallization and/or grain growth were not observed during the second anneal, indicating that intersections such as Fig. 1 are equilibrium configurations. Many such stacking faults were observed, but few were noted as intersecting grain boundaries in well-illuminated areas. The intersection of Fig. 1 was well away from the specimen edge. Since similar defects have not been observed in fully recrystal-lized and annealed copper, it is felt that this defect is due to the tensile straining. Electron transmission

Jan 1, 1970

By Bob J. Rawicki

TYPES OF WET DUST COLLECTORS Basically, there are two types of wettype dust collectors. One is mechanical, incorporating pumps, motors, fans, sprays, filters, or flooded beds. These come in many forms, but their operating principle is basically the same. The screen or flooded bed is wetted by a series of sprays. Polluted air is drawn in through a fan; here the dust particles impinge on the screen and are flushed off into a settlement tank. The air then passes through spray eliminators to the atmosphere. A great deal of time and money has been spent developing this type of collector. In laboratory tests where clean water at constant pressure, air at constant volume, and dust at low but constant mass to volume were applied, these collectors gave high percentage dust collection efficiencies. Theoretically and technically, they are very good. In practice, however, under rugged mining conditions where there are no constants, and dust load, particle size, water pressure, and volume of air vary with time, their efficiency varies dramatically. Some of the most common problems are: 1. clogging of screens 2. blocking of nozzles 3. replacement. of damaged pump stators Any of the above result in loss of air flow and dust collection efficiency. Generally, there are so many mechanical moving parts, something is always breaking down. This type of collector is very expensive in parts and labor to maintain. The second type of dust collector, which I personally developed, with the help of the British National Coal Board of Great Britain, has none of the above mentioned problems and it works on a completely different principle. My collector, the Mark III Precipitaire Wet-Type Dust Collector, (an improved version of previously successful models) has no internal moving parts, no flooded beds, screens, spray nozzles, etc. It is highly efficient - 99.8% efficiency on total collected dust and 97% on respirable dust. The pressure drop through the collector is constant, hence, air flow remains constant. There is no maintenance expenditure, be it labor or parts. The only maintenance that there is, is desludging. This, of course, varies with the dust load. With a low dust load, desludqinq may only be required every 4 weeks, but this is a very simple operation that can be handled by unskilled men and it takes only a very short time. My collector is powered by a ventilation fan that is placed on the clean air side for a longer fan and motor life. Dust is extracted solely by water action. The collector&apos;s operating principle is: Dust laden air is drawn in along ducting into a tapered scrubber section, shaped to create a self-induced curtain of water. This action washes the dust particles from the air and the collected dust settles into the bottom of the tank. Cleaned air is then exhausted via a series of spray eliminators where it is completely dried and on into the atmosphere. These collectors have been sold in Great Britain, to the National Coal Board, and throughout Europe. They have been working very well for many years now. GENERAL APPLICATIONS Dust is very dangerous; silicosis and black lung kill and disable many workers each year. Many of the mine explosions can be attributed to coal dust. By the use and application of dust collectors, these deaths and disasters can be avoided. There really is no excuse. However good and efficient a dust collector may be, it&apos;s positioning and installation arrangement is critical. The collector may remove 99% of dust supplied to it, but it takes the skill and experience of a dust control engineer to design and fit ducting, hoods, etc. to remove polluted air at source and deliver it to the collector. In some cases this is very simple; in the case of longwall machines, it is very difficult. In general, dust collectors should be used to collect dust at every point of dust generation. I have noted a great reliance on dilution as a means of dust control. I personally think this is a dangerous and unreliable method. As mines become deeper and the use of larger and more productive equipment becomes more common, reliance on dilution will be impossible and dust collectors will be essential.

Jan 1, 1982

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer&apos;s opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films&apos;! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By H. R. Crawford, P. B. Crawford, A. F. Tragesser

A method has been developed to calculate wellbore temperatures during mud circulation and the actual cementing operation to aid in the design of cement slurries. The method agrees within 10F with previously measured values. The calculation technique provides temperatures, as functions of time, at varying depths in both the casing and annulus. The technique also provides this information if a relatively cool cement slurry is pumped into the well immediately following circulation of hot mud. Circulating bottom hole temperatures of brine and a bentonite mud were measured. INTRODUCTION As wells are drilled deeper, greater demands are being made on all phases of the industry, and new technology has been developed to provide satisfactory well completions. However, little or no work has been conducted on accurately determining bottom-hole, static and circulating temperatures.. In designing a cement slurry, such factors as density, fluid loss control, viscosity, deterioration from ternperature, compressive strength and pumping time must be considered. Individual well conditions often make it necessary to include still other factors. Pumping time is a primary consideration and, as wells are drilled deeper, encountering higher bottom-hole temperatures, this property becomes even more important. Cement slurries must be designed with sufficient pumping time to provide safe placement in the well; however, the slurry cannot be overly retarded as this will prevent the development of satisfactory compressive strength. The pumping time of a specific cement is currently obtained by subjecting the cement to simulated conditions of temperature and pressure. A reasonably accurate bottom-hole pressure may be obtained by considering hydrostatic heads of fluids, friction pressure and wellhead pressures. However, accurately determining bottom-hole temperatures is much more difficult. Bottom-hole static temperatures are estimated by considering several sources of information, including logging temperatures, published temperature gradient maps and field experience. This information is usually questionable due to disagreement of data from the various sources. Temperature gradient maps were constructed based on temperatures recorded many years ago while running bottom-hole pressure tests. These thermal gradients then represent an average of well conditions and cannot always apply to a specific well. Also, logging temperatures may be affected by the time since fluid was last circulated, rate of penetration, circulating rate and many other factors. Therefore, even though logging temperatures are available, the question still exists as to the correction factor that should be applied to obtain an accurate static temperature. After obtaining static bottom-hole temperature, it is then necessary to relate this to circulating temperatures actually encountered by the cement slurry. This is accomplished by selecting a test schedule from the API RP-10B corresponding to the estimated well conditions.&apos; The API-recommended practice for testing oilwell cement provides testing schedules for various well depths and conditions. These schedules are intended to simulate down-hole conditions during cementing. They provide a rate at which both temperature and pressure are increased until the estimated circulating conditions are reached. These testing schedules represent circulating temperatures for an average well and, although there is flexibility in choosing the test schedule that most accurately simulates the temperature of an individual well, it still is not possible to consider all the well conditions that will affect the bottom-hole temperature. Many factors affect cement temperatures; for example, the length of time a well has remained static prior to running casing and cementing, the circulation time, the temperature of fluids used in cementing, fluid density and flow properties of fluids. The pumping time for a typical retarded cement could vary from 2 to 4 hours with a 10F change in testing temperature. Variations in pumping time are the most critical in highly retarded cements used in deep, hot wells; yet, predicting bottom-hole circulating temperatures is more difficult in these wells. This work was conducted to develop a means of calculating circulating temperatures as a function of well depth, casing and hole size, pumping rate and time, fluid and reservoir physical properties and thermal status of the well. PREVIOUS WORK In 1941 Farris reported on a study to develop information leading to a more practical laboratory evaluation of oilfield cementing mixtures and performance.&apos; It was then recognized that the pressure factor was being neglected,

By R. D. MacDonald, John Dasher, A. M. Gaudin

ION exchange is a widely used unit operation in water treatment and elsewhere in chemical industries. It has occasionally been used in hydro-metallurgy for treating plating, pickling, and rayon wastes Concerning ion exchange in extractive hydrometallurgy—for treating ore leach solutions— the literature prior to the Geneva Conference has given only hints."-" Yet most of the ore leach plants now being built or completed in the last three years use ion exchange for this purpose. Most of these plants are used for extracting uranium. The overall process for leaching low grade uranium ores and the history of its development have been given in the authors&apos; previous papers.&apos;,&apos; The object of this paper is to discuss certain engineering aspects of the new application of ion exchange to recover dissolved values from ore leach solutions. Necessarily the illustrations will be taken from the first application—to uranium metallurgy. Although ion exchange processes have been devised in which separation of spent residue from pregnant liquor is not required, as in the RIP process,"-&apos;I only ion exchange operation, in which the resin is contacted with a clear solution, will be discussed in this paper. Uranium exists in acid leach liquors mainly as the cation UO," and can be adsorbed completely by cation exchange resins, but the adsorption is not selective as other cations such as Fe++, Fe+++, Al+++, Mg++, Mn", and Ca++ are also adsorbed. Uranium, however, forms complex anions with sulfate, phosphate," Carbonate"~"~ and even with chloride if the solution is strong enough.15 These anions can be adsorbed by anion exchange resins. The strong base anion exchangers have a very strong preference for these complexes and hence this adsorption is very selective. In this paper, the examples concern acid sulfate leach liquors from which uranium is adsorbed as UO,(SO,),-% and UO,(SO,),". Materials and Equipment Ion Exchange Material—Ion exchange materials include natural and synthetic; organic and inorganic; cationic and anionic; and weak, intermediate, and strong varieties. They consist of fragments or beads normally in the size range —16 to $50 mesh. The newer varieties have been developed to have greater stability, chemical strength, and/or capacity than earlier varieties. The resin used for uranium recovery is a strong base anion exchanger.* To make * Such as Rohm and Haas Amberlite IRA-400 series, British Permutit DeAcidite FF. Permutit lonac SE. and Dow Nalcite SAR. this resin, styrene plus a few percent divinyl benzene are polymerized into long chains with occasional cross links. This resin in bead form is then reacted to introduce quaternary amine groups onto most of the aromatic rings.&apos; These resins are water-avid gels of specific gravity of about 1.1, which shrink and swell by osmosis when the ionic content of the surrounding solution is changed. The beads which are shown in Fig. 1 can be broken like an onion by rapidly replacing 15 pct H,SO, with water. This organic gel can also be broken by mechanical handling as by a centrifugal pump. Otherwise it is remarkably stable. It is unharmed by fairly strong acid or alkali, oxidizing or reducing agents, and heat up to 70°C. The strong base resin when completely in the chloride form (with a chloride anion on each quaternary amine group) holds over 107 g of C1- per dry kg. As all these chloride ions can be displaced by other anions, the resin has an exchange capacity of over 3 g equivalents per dry kg. However, the resin is sold and used by moist volume. The moist resin contains about 50 pct water, weighs about 43 lb per cu ft, has 40 pct voids, and an exchange capacity of over 1 g equivalent per liter of bed volume. Ion Exchange Equipment—Ion exchange equipment used for recovery of uranium from leach solutions is substantially identical to that developed for water treatment and other applications.&apos;" The resin beds are held in closed tanks or columns which, in the uranium plants, have been standardized at 7 ft diam and 12 ft high. The resin bed

Jan 1, 1958

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,&apos; whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham&apos;s work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy&apos; found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By E. Martinez

Samples of chrysocolla, a hydrated copper silicate, from several sources were submitted to differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). Pure samples of chrysocolla are difficult to obtain, but comparison of the thermograms revealed that certain reactions occurred in all the samples and it is believed that these are due to chrysocolla. Endothermic reactions occurred at 50&apos; to 175°C, 350° to 650°C, and 980° to 1100°C each of which caused a weight loss. The first was due to loss of absorbed water, the second to a dehydroxyla-tion, and the last to conversion of cupric oxide to cuprous oxide. In addition, two exotherms were detected at 685° to 695°C and 935° to 950°C. Infrared spectra of heated samples indicated the exotherms were due to changes in the Si-O bonds leading to the formation of cristobalite. The results suggest that thermoanalysis may be a more sensitive and reliable method for detection and identification of chrysocolla than X-ray diffraction, infrared spectroscopy, or optical techniques. The recovery of copper from oxide ores has been the subject of much research in recent years. One of the principal oxide copper minerals is chrysocolla, a hydrated copper silicate. The information available indicates that it has widely varying properties depending on the origin of the sample. Chrysocolla usually is found associated with cuprite, malachite, azurite, and native copper. Most of these other minerals are recoverable by present day flotation practice, but chrysocolla is lost in the tailings.1,2 Reagent combinations that are successful in laboratory chrysocolla flotation with ore from one source have been found to be ineffective with another. 3 The copper segregation process offers an altemative to beneficiation of oxide copper ores.4&apos;5 The process is of particular interest in processing ores that cannot be treated by conventional hydrometal-lurgical methods because of high acid consumption.6 Fuller understanding of the properties of chryso- colla may prove of value in the search for improvements in both the flotation and segregation processes. Chrysocolla samples from Arizona, Nevada, Chile, Australia, and South Africa were studied by differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). In addition, a sample from Miami, Ariz., was submitted to X-ray diffraction, infrared spectrophotometry, and surface area determination. EQUlPMENT Differential thermal analysis (DTA) detects, amplifies, and records exothermic-endothermic reactions occurring in a sample as its temperature is raised at a constant rate, usually 10°C per minute. A unit made by the Robert L. Stone Co. was used in this study. The tests can be run if desired with a gas streaming through the sample. A thermobalance records weight losses or gains in a sample as its temperature is raised at a uniform rate. The gravimetric analyses (TGA) were run on a Chevenard thermobalance converted electronically for graphic recording. A heating rate of 5°C per minute up to 1100°C was used in these tests. A Perkin Elmer Infrared Spectrophotometer, Model 221, was used with sodium chloride optics obtaining IR spectra in the 2 to 15 region. A pressed pellet technique with potassium bromide was used in preparing the samples. DESCRIPTION OF SAMPLES Chrysocolla is found in the oxidation zones of copper deposits commonly associated with malachite, azurite, and limonite. It is described as varying in composition and in color from bluish green to brown or black. Inclusions of other minerals are usual so chemical analysis of chrysocolla samples may be suspect. However, it is considered by many to be a solid solution of CuO, SiO2 and H2O with a general formula of CuO.SiO2.2H2O or 2CuO.2SiO2. 3H20. Chukhrov7 has described a sample from the Urals as CU3,5(OH)2 (A1Si3) O10.nH2O and stated that chrysocolla is a montmorillonite-type mineral. On the basis of X-ray analyses, DTA, and infrared spectra of chrysocolla from the Inspiration Mine, Ariz., Sun8 concluded that there was no substantial evidence to classify it as a montmorillonite mineral. Chrysocolla samples from many sources throughout the world were used in this investigation. The following is a brief description of each:

Jan 1, 1963

By R. J. Lutton

Empirical data from 91 rock excavations have been used to construct a family of slope curves on a chart relating excavation height and inclination. The highest and steepest slopes from each excavation are plotted and connected by a line. The 31 1ines appear to establish one or two geometrical slope fields through which the curves are projected. The curves apparently represent a lumped eflect of many factors too complex to be considered individually. Important factors such as geological structure or ground-water conditions can dominate the picture, but where these factors do not overshadow others, the slope chart should be useful for estimating or checking optimum inclination. The U.S. Army Corps of Engineers (USAE) has been engaged since 1962 with the U.S. Atomic Energy Commission in a joint research program to develop nuclear excavation technology. The Corps is responsible for collecting the requisite data on engineering and construction problems associated with nuclear excavation. The ultimate objective is to develop a capability to use nuclear explosives as a construction tool on public works projects such as harbors and canals. The present study on empirical inclination-height curves for conventionally excavated slopes is an outgrowth of an investigation&apos; sponsored by the USAE Nuclear Cratering Group on applicability of data from existing excavations in establishing guides for engineering judgment in crater excavation. Data were generously contributed by over 50 mining companies among other organizations. Inasmuch as several companies preferred that their contribution be anonymous, all data are treated so here. Some Factors Affecting Stability Many factors affect or are suspected of affecting the stability of excavated slopes, e.g., adverse structural orientation, degree of structural ordering, ground water, climatic conditions, mechanics of excavation, and plan-profile configuration. Such factors are lumped together in developing a slope chart. Obviously geological structure and ground water can overshadow all other factors. Where such is the case, the simplification of slope charts may give an erroneous picture (not conservative enough). A further complication results from the fact that the concept of stability may vary according to the use of the excavations. For example, slope adjustments that would be regarded as failure in a powerhouse excavation, might be tolerable in a mining operation. Mine slopes are continually being modified by further excavation, and instability that would develop in a similar permanent excavation slope over a period of years might not have time to develop in a mine. Inclination vs. Height Charts Charts of inclination vs. height for particular formations or conditions have been used in the past as an aid for designing excavation slopes. Some of these have been based upon empirical analyses of collections of data and experience. MacDonald" and Lane have presented slope tables and charts for excavated and natural slopes in relatively weak sandstone and shale. Coates&apos; has shown an inclination-height chart for slopes in incompetent rock. Most organizations have developed slope design criteria which relate bench widths, heights, and inclinations to use in various rocks. Slope data collected in present studies can be similarly used to develop inclination-height charts; however, a plot of all slopes on such a chart shows very little because of the wide spread of the data. Reasons for the dispersion of points are: (1) many slopes are not carried at optimum inclination, particularly in mines where maintaining roadways and following irregularities of ore bodies are more important than achieving steep inclinations; (2) many engineers and geologists with varied backgrounds and viewpoints have been involved in designing these slopes; and (3) each slope is characterized by a unique combination of factors affecting stability and in turn optimum inclination. Significant curves can sometimes be constructed where the points can be grouped into related clusters from the same excavation. The essence of this approach appears when only two slopes from each excavation are considered—the highest slope and the steepest slope, connected by a line segment (Fig. 1). This reduces considerably the usable data because in many cases only one of these two slopes is available. Nevertheless, the concession seems justified. Construction of Slope Curves Ninety-one pairs of points and connecting line segments were assembled in this study. The line segments were assumed to approximate a geometrical slope field (Fig. 2), and a family of curves has been visually projected through to represent the slope field. It should be

Jan 1, 1971

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,&apos; a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,&apos;9 it hydraulic horsepower and jet impact force,&apos; each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company&apos;s coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company&apos;s office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy&apos;s military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers&apos; training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By K Faure

At Sams Creek a gold-bearing, peralkaline granite pophyry dike intrudes Ordovician-Silurian metapelite and quartzite. These metasedimentary rocks have undergone three phases of folding: a first phase of recumbent folds (F1), a second phase (F2) of northerly-trending inclined folds with a prominent crenulation cleavage, and a third phase (F3) of steeply plunging folds. The granite porphyry dike has a thickness of up to 40 m and intrudes thin lamprophyre dikes along its contacts. Deflection of the crenulation cleavage around the granite dike, shearing within the dike and its sinuous outcrop pattern indicate that the granite dike has been deformed during F2 and F3. The granite has been hydrothermally altered, with a first stage of magnetite-ankerite alteration. This first stage is cut by a second stage of quartz-pyrite veins and a third stage of sulphide, quartz and ankerite veins, accompanied by pervasive silicification represented by quartz-perthite-albite-rutile¦pyrite-ankerite-sericite assemblages. Lamprophyre is altered to an ankerite-chlorite-sericite assemblage. The sulphide veins are composed of arsenopyrite + pyrite ¦ gold ¦ galena ¦ sphalerite ¦ chalcopyrite ¦ pyrrhotite. The altered granite and the veins have been deformed and recrystallised. The competent sulphide minerals pyrite and arsenopyrite are fractured and brecciated, with fractures locally filled by galena, a ductile sulphide mineral. Vein quartz shows local cataclastic and mortar textures and develops pressure shadows around arsenopyrite. Alteration and mineralisation are confined to the granite porphyry and adjacent lamprophyre. These features together with the style of veining and the sulphide mineralogy indicate that the mineralisation was formed from a magmatichydrothermal fluid that was sourced from the granite. Oxygen, carbon and sulphur isotope values of the vein minerals (quartz, ankerite and sulphides) are also consistent with a magmatic source.

Jan 1, 2003

By H. P. LeVan

The aced for reliable reserves of the essential element, manganese, has been a continuing concern of the Federal Government for more than three decades. Because of the increasing vulnerability of outside sources of supply efforts have been intensified to find a means for beneficiating United States domestic deposits. The deposits of most interest would of necessity be near, or have access to, suitable transportation to processing plants. The Georgia manganiferous iron deposits represent some 10 million tons4 of ore readily available to southern iron and steel industries, if a manganese recovery process capable of functioning in the presence of large quantities of iron can be developed. In addition, a successful method for beneficiating the Georgia ore could produce a significant quantity of high-grade iron concentrate. The Differential sulfatization process developed 47 the Bureau of Mines5 seemed to be well suited for this application, particularly because it results in low concentrations of iron in the leach liquors with relatively complete extractions of manganese. In this process, manganese in the presence of iron is preferentially reacted with sulfur dioxide at elevated temperatures and subsequently extracted with water.

Jan 1, 1962

By Michael Godard, Peter Cleyle

"Suncor Energy’s Project Millennium increased oilsands production capacity by an additional 95,000 barrels per day to its present level of 225,000 barrels per day. This massive venture included an expanded Mine, new Extraction and Upgrading facilities, as well as, steam and utilities infrastructuresIn the Primary Extraction process, removal of the bitumen from the oil sand begins with slurry preparation and is followed by primary , secondary and tertiary separation processes. The final cleaning step of the bitumen froth is the Secondary Extraction process, that removes residual water, mineral and solids to produce a clean diluted bitumen suitable for Upgrader feedstock.This paper will review the flowsheet of the Millennium Primary Extraction facility, from its recent commissioning through the ramp up to design production rates. In addition, new technologies in the Primary Extraction flowsheet will be reviewed.INTRODUCTIONAs conventional supplies of oil and gas are depleted in Canada, the Athabasca oil sands industry of Alberta becomes an increasingly important source of energy. Today, high quality crude from Alberta’s oil sands accounts for roughly 30% of Canada’s daily petroleum production. According to government projections, over the next 7 years, oil sands production is expected to more then double, and by 2010 more than half of Canada’s crude oil is expected to come from the oil sands.Oil sands deposits consist of a layer of sand saturated with bitumen covered by a muskeg overburden and underlain by silt and clay. The oil sand is mined where the overburden is economical to remove, typically less than thirty meters thick. The Athabasca oil sand deposits around Fort McMurrray is ideal for mining. Bitumen can be described as a diverse collection of hydrocarbons, organosulfur, and nitrogen compounds."

Jan 1, 2004