Search Documents

By John E. Litz

Since the 1974 introduction of catalytic converters to automobiles in the United States, more than 150,000 kg (5,000,000 oz) of platinum, palladium, and rhodium have been used in the converters. An estimated 8 to 10 million converters are being used annually in the United States, each containing from $5 to $15 of PGM metals. In addition, use of converters is beginning in Europe which will significantly increase the quantity of PGM used. Two basic types of catalysts for converters are being used: pellet and monolithic. The pellets are small, discrete spheres or cylinders of gamma-alumina coated with platinum group metals, Figure 1. The monolithic are honeycombs of a cordierite, A13(Mg,Fe)2Si5AlO18, base coated with gamma-alumina and subsequently with platinum group metals, Figure 2. Pellet catalysts are being used by General Motors and American Motors; whereas Ford and Chrysler are using monolithic catalysts. The table below compares the PGM content and value of the catalysts.

Jan 1, 1986

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese-grade ore 6/ from the wide-spread domestic manganese and manganiforous iron deposits. Samples for testing were received from the Interstate Manganese Co. in northeastern Tennessee, 11 miles west of Mountain City and 10 miles southwest of Damascus Va. The ore deposit occurs in the residual material of the Shady dolomite 7/ as an unconsolidated mixture of hard and soft manganese oxides and clay.Numerous tunnels and pits have developed a large reserve of ore in an area of about 15 acres. One pit 250 by 50 by 20 feet is being mined by rower shovels. The ore is hauled to a washing plant for log-washing, hand-sorting, and jigging. Coarse concentrates from the washing plant are marketed without further beneficiation.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. F. Fisher, who made the roasting and magnetic tests."

Mar 1, 1942

By Richard F. Hewlett

The purpose of this paper is to provide a framework within which problems in the evaluation, development, and operations of a mineral property can be solved, Solution of these problems must be made with a computer because of their complex nature, Individual problems will be collectively discussed in terms of an overall objective - computation of the optimum mine limits. The concept of quantifying geologic and mine sampling data has been advanced and demonstrated in the United States by two pioneers in the application of statistics. These men are, respectively, Dr. W. C. Krumbein Northwestern University, and S. W. Hazen, Jr., U. S. Bureau of Mines, Dr. H. S. Sichel and D. G. Krige of South Africa have pioneered specific applications of statistics, particularly to gold deposits. Implementation of statistical and mathematical methods to the solving of problems in the mineral industry creates the need for a computer. The steps required to solve evaluation, development, and operational problems with a medium sized computer are discussed in this paper.

Jan 1, 1963

By S. M. Rupprecht

Transportation accounts for some 26% of all mine accidents in South Africa. Although this figure may not be as prolific as fall of grounds accidents or accidents caused by seismic events, the enormity of transportation accidents demands attention, especially as many of these accidents are avoidable. This paper investigates vertical (i.e. shaft), horizontal (i.e. haulages), and in-stope transportation systems and their function as it applies to safety. Recent transportation accidents are discussed looking at current trends within the three transportation areas. In the shaft area, discussions will focus on handling of material cars, loading and off-loading of the workforce and management of shaft orepass systems. The horizontal component will focus on personnel transportation, safety around trains and hoppers, and handling of material in the cross-cut. The discussion on in-stope transportation will focus on the general congestion of the stope environment and how it affects the overall movement of personnel, material, and rock. Of concern are the large numbers of material handling and scraper winch accidents that occur and which will be discussed in some detail. The paper will conclude with a section on proposed guidelines within the three above-mentioned systems for mine engineers to consider in mine design and life of mine planning and scheduling. Keywords Underground logistics, safety in material handling.

Jan 1, 2011

By AIME

WE got our chance to talk with Arthur J. Blair at the Annual Meeting at the Pennsylvania Hotel. By two o'clock Wednesday afternoon things had quieted down enough so we had our interview in the foyer to the Ball Room. There were the usual questions. Where were you born? In La Salle County, Ill., on March 26, 1885. Where did you go to school? Northwestern University, B.S. degree in 1906. Where did you start work? For E. J. Longyear right after leaving school. One's ability as a geologist was measured by one's ability to wield a brush hook and ax. He stayed on the job as geologist for three years and then got to thinking about the advantages of a warmer climate. The advantages stacked up favorably, so off he went to Birmingham, Ala., just about the time U.S. Steel took over the Tennessee Coal, Iron and Railroad Co.

Jan 1, 1948

By E. Jackson

This paper describes highlights of the Placer Dome MiniMole project - the development and testing of a robotic machine for mining narrow ore veins. A prototype hydraulically controlled robotic machine was built and tested. The machine provided a platform for testing numerous cutters in the field. Other cutters, e.g. undercutting devices, were tested in the lab. Extensive analyses were done on specific energies and cutter penetration. Three sets of quarry trials were done, then the machine was tested in an underground mine. Rock UCS values varied from 180 MPa to 230 MPa. The paper includes lessons learned and recommendations based on the project findings.

Jan 1, 2007

By Patricio Santis, Jacopo Seccatore

Artisanal and Small-scale Mining (ASM) is a prominent activity in the extractive industry: considering only gold, it produces about 20% of world market supply. Despite this fact, ASM is generally associated with negative aspects of its environmental impact, and operational research is generally neglected. This paper emphasizes the peculiarity of the drilling and blasting systems of small underground mines in selected South American Countries. Such Countries, while having large mineral deposits and well recognized large-scale mining activities, at the same time still present on their territory ASM activities that are archaic, highly inefficient and dangerous for the safety of its operators. This paper documents drilling and blasting activities from gold mining in Ecuador and Chile. First, are described the outdated and often non-rational techniques employed by miners, to provide a general framework of the current methods. Then, it is shown what can be improved and how the current methods can be modified. Finally, are shown some field applications and the comparisons of the results obtained. One case shows how blast pull efficiency can be increased of from 82% to 98% by changing non-rational applications of explosive products. Another case shows how, by rationalizing blast designs, drilling and blasting costs can be reduced by 9% per month, the advance by blasting increased by 29% and the blasting efficiency increased from 70% to 90%. Finally, it is concluded that examples of application show how operational improvements are easily applicable on the field, relying only on tools and resources of artisanal mining, but combining solid engineering bases with confidence-gain and respect for the experience of the miners.

By AIME AIME

BORN a Chicagoan, on Aug;. 31, I879. Oscar Johnson lived in that city until young manhood. As a youth delivering newspapers he set his sight on the l university of Chicago and at sixteen years of age he began working summer vacations in the foundry of the Pullman Company. Misfortune came to his family during the summer of 1898 when tuberculosis took his only sister and brother. His mother, apprehensive of Oscar's health, urged him to try the West at least for awhile. So late summer found Oscar in Salt Lake City, employed by the Trent Engineering & Machinery Co. At that time it was busy building equipment for use in the war with Spain. Though he did not know it then, Oscar war was laying the groundwork for his present membership on the Mining Equipment Industry Advisory Committee of the W.P.B., a post which keeps him commuting between Denver and Washington.

Jan 1, 1944

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By AIME AIME

CONCIDENT with what promises to be a record-breaking year of activity in the world's greatest iron-ore district is the announcement of plans to hold the regional meeting of the American Institute of Mining & Metallurgical Engineers at Duluth, Aug. 12 to 15 in¬clusive. More than 25 open-pit mines will be in operation in Minnesota's great iron-ore district this year, affording to those attending the convention an unusual op¬portunity of viewing practically side by side the interesting activities of power-shovel operations, railway haulage, truck haulage, conveyor-belt haulage, tower-excavator operations, iron-ore concentration, and underground mining. The ore can be followed from the mines to washing and concentrating plants and to the docks and lake carriers on Lake Superior, where an average of one boat of 10,000 tons' capacity will be loaded and depart every 15 minutes, day and night, during the 1941 shipping season.

Jan 1, 1941

By AIME AIME

EUGENE AUSTIN STEPHENSON, better and affectionately known as "Steve," has long been an active and enthusiastic member of the Petroleum Division of the Institute. As its Secretary-Treasurer for several years, he was the spark plug that so successfully carried the Division over the trying period of the early thirties. "Steve" was born at Franklin, Mich., July 27, 1883; graduated from Adrian College in 1905, and later received his Doctor's degree from the University of Chicago where he was an instructor for two years. From 1917 to 1925 he was chief geologist for the South Penn Oil Co. and from 1925 to 1930 he was associated with Ralph Davis, Inc., of Pittsburgh, consulting engineers. In 1930 the Missouri School of Mines called him to Rolla to head a department of petroleum and natural gas engineering. and in 1938 he was invited to build up a similar department at the University of Kansas.

Jan 1, 1941

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

By V. Soloviev

The world?s data available on near sea-bottom gas-hydrate accumulation and deep-water fluid-discharge areas are presented in this paper. Gas-hydrate accumulation associated with fluid discharge (mud volcanoes, gas seeps, gas-saturated water seeps) is characterized by the following. First, the largest hydrate accumulations in sediments are located at shallow subbottom depths and have well-defined limits, especially in the upper subbottom part. Second, gas-hydrate formation in fluid-discharge areas is a present-day process, with the global occurrence of deep-water fluid-discharge areas numbering up to about ten thousand, and with all the seep areas being favorable for the formation of near-sea-bottom gas-hydrate accumulation. Third and principal, gas resources in the hydrates can be considered as renewable. Estimates of possible gas volume in single accumulations of hydrates and the global budget, as well as possible methods of gas utilization from such gas-hydrate accumulations are discussed in the paper.

Jan 1, 2005

By J. Kretschmann

?We have constructed a world in which the potential for high-tech catastrophe is embedded in the fabric of day-to-day life.? (Malcolm Gladwell) The mining industry is a crucial provider for virtually every person?s needs and thus indispensable. Yet, mining is a complex and risky business: plenty of high risk factors can occur and severely affect nature and the miner?s life and health. Especially for small and medium enterprises (SME) risks may also threaten the economic existence of the company. The responsible and sustainable management of a company should thus be based upon the systematic finding and handling of risks or briefly upon an efficient risk management system. Why do we need risk management? Because nobody is perfect and we make mistakes in the normal course of operation.

Jan 1, 2011

By Madan M. Singh

It is estimated that through 1975, there were 1.69x109 m2 (418 000 acres) of urban land threatened by potential subsidence due to mining with a value of over $12 billion (19;3 dollars; USBM, 1979). With increased coal production to meet the energy needs of the nation, both these figures may be expected to increase. Hence greater attention to controlling surface damage due to subsidence is merited. In fact, the Surface `lining Control and Reclamation Act of 1977 (SMCRA) (Public Law 95-87) mandates that underground coal mining operators "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, ..." The term "subsidence," as used in this paper, implies the total phenomenon of surface effects associated with the mining of minerals, and not only vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

By Julie Q. Shang

The electrokinetic (EK) technology for dewatering of two tailings from the uranium mines in Northern Saskatchewan is studied in bench scale experiments. The study includes four phases: 1. Characterization of two uranium mine tailings; 2. Assessment of voltage loss on the coated Ti anode and water interface. 3. EK cell test series to measure electrokinetic permeability (ke) of two tailings; 4. EK dewatering test series to study electrokinetic enhanced gravity dewatering on two tailings samples. The results have demonstrated that both tailings responded positively to the EK process. For the tailings containing gypsum, the EK dewatering should be a short term process (within one hour) with anode conditioning (pH adjustment). The tailings containing clay minerals responded well to EK dewatering, in which pH adjustment is optional and will further enhance the EK flow. Both tailings as tested have low hydraulic conductivity and are particularly suitable for EK dewatering and consolidation.

Aug 1, 2010

By AIME AIME

THE 1944 Chairman of the Institute of Metals Division might be classed as metallurgically ambidextrous ; he is teacher of theory and practice of both nonferrous and ferrous metallurgy, and he is consultant on brass and on highspred steel. Arthur Phillips was born in Troy N.Y. and attended the New Haven Connecticut high school. Upon graduation he entered Yale, receiving a degree in metallurgy in 1913. At that time Professor Mathewson was starting his plan of '"co-operation with the metal industries in metallographic work at the Hammond Laboratory of the Sheffield Scientific School, Yale University, and Arthur Phillip, became the first co-operative graduate student, working in the laboratory of the Bridgeport Brass Co., and receiving his Masters of Science degree in 1915. A little later, when the department of metallurgy at Yale was expanded. Me. Phillips was appointed assistant professor. In 1928 he was made associate professor, and in 1934 he was promoted to full professor.

Jan 1, 1944