Search Documents

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

The purpose of this study was to investigate the effectiveness of froth fl otation for the recovery of gold from the gravity tailing stream of the former Lihir Gold Limited (LGL) operation in Ballarat. The P80 of the tailings was determined by screen analysis as 1 mm, with test work conducted on as received material along with samples ground to P80 sizes of 47, 78 and 134 microns. Laboratory scale batch flotation tests were conducted at both natural and elevated pH to investigate the impact of pyrite depression on gold recovery. Results indicated that although an increase in grade from approximately 0.7 g/t to 3 g/t was achievable at a natural pH and a P80 of 134 micron, gold recovery was low at just 35 per cent. Finer grind sizes were found to have an adverse effect on both grade and recovery. Future efforts will be focused on the sub 310 micron size fraction of the tailings, which was revealed to contain approximately 85 per cent of the available gold and may be amenable to cyanidation or ultra-fine gravity treatment.

Aug 1, 2010

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Selby J

South Australia's economic development has relied heavily on the mineral industry. In the late 1840s the rich copper deposits at Kapunda and Burra saved the Colony's economy when South Australia became a world copper producer. Copper lodes developed at Moonta-Wallaroo during the 1860s brought further prosperity when mining activities at Kapunda and Burra were in decline. In addition to those large mines there were many smaller workings scattered through the Flinders and Mount Lofty Ranges producing copper, gold, silver, lead and zinc. Most of the mines of this period were worked by Cornish immigrants who brought their own technology and mining methods with them. These people have left a cultural legacy unique in Aus- tralia. In this Jubilee 150 year (1986) the Department of Mines and Energy, working in conjunction with the Department of Environment and Planning, is helping to preserve and interpret selected historic mining sites, most of which have been neglected since their closure. This work is designed to draw people's interest to mining history by providing interpreted sites for them to visit and to demon- strate the importance of the mining industry in South Australia's cultural and economic develop- Ment.

Jan 1, 1987

By Martin A. Elliott

"INTRODUCTION During the recent war the Bureau of Mines was requested to obtain in¬formation on the temperature at which ammonium nitrate mixed with certa: contaminants would react rapidly. This information was desired in connection with an investigation of an explosion that had occurred during the evaporation, by air agitation, of volutions containing ammonium nitrate in which compressor oil that might have passed the filters was suspected of being a contaminant.During the course of this work it was found that mixtures of ammonium nitrate and zinc reacted rapidly at comparatively low temperatures: and since zinc could not positively be eliminated as a contaminant in the explosion in question, a series of tests was carried out, not only with mixtures of ammonium nitrate and compressor oil but also ammonium nitrate and zinc with and without oil. A few experiments were made with metals other than zinc.The investigation was not as extensive as might have been desired, owing to limitations -in time. The results are presented at this time in view of their current interest in connection with the Texas City disaster, in which a large quantity of ammonium nitrate detonated in the holds of two ships."

Mar 1, 1948

By William F. Boericke

CONSIDERABLE waste of oil and grease in lubricating motors and other machinery results from the use of bearings that are not totally enclosed. There is also the likelihood of damage to the bearing through the accidental introduction of grit or dust both in the oiling process and after, unless the cover is entirely dustproof. With the ordinary sleeve bearing that is only partly enclosed, it is generally easier for a careless attendant to cause trouble through neglect than with the ball bearing type, which from its design, must be totally enclosed to give effective service, and needs a minimum of attention. At one of the large mining companies which has taken a leading part in reducing unit costs and pioneering new developments in mining machinery, ball bearings have been gradually supplanting the conventional type of sleeve bearings on many of their motors, centrifugal pumps, and other machines in the mines. This innovation is not recent, as substitution of ball bearings on mine motors was first tried out by this company in 1909. Since then an increasing number of such bearings have been put in. They are now favored because of increased operating efficiency and reduction in lubrication costs.

Jan 1, 1926

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022

By Y. M. Zhu

Lead in environment often causes a serious health hazard. The removal of Pb2+ from aqueous phase is a beneficial project. In this paper, deposited Saccharomyces cerevisiae (S.c.) was chosen as adsorbent, Pb2+ ions as adsorbate, and the process of biosorption was studied. The dynamics of the adsorption was investigated. The adsorption mechanism of Pb2+ by S.c. cells was also investigated by detecting microstructure, zeta potential under different pH value, FT-IR spectra of the S.c. particles before and after biosorption. It was shown that the biosorption of Pb2+ by deposited S. c. is a rapid process, and the adsorbing equilibrium is reached within 10 minutes. The Zero point of zeta potential of S.c. cells is pH=3.3. When 2.0<pH<3.3, there exists biosorption (biosorption rate 76%~88%), which means static bio-sorption been not the only kind of biosorption. FT-IR spectrum analysis showed that groups on bacteria surface were mainly characteristic groups of protein and amylase; oxo-groups and nitric-groups on S.c. cell surface could chelate with heavy metal ions. Chemical adsorption might exist in the process.

Jan 1, 2014

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By C. P. PERIN, DONALD BELCHER

T HE production of pure iron by electrolyzing solutions of its salts has been the object of scientific curiosity and research for about 80 years; and in the last two decades a realization of the unusual physical and chemical qualities of electrolytic iron has turned the attention of chemists and metallurgists toward a commercial application of this accumulated knowledge. Thus Burgess and Hambuechen in America, . Cowper-Coles in England, and Fischer in Germany- devised methods, more or less successful, for the electrolytic refining of iron, but none of these processes has yet attained large-scale operation. During the war some interesting ,work was done in France and England on building up worn or defective machine parts by electrodeposition of iron. It remained for the Société "Le Fern in France to carry on the process commercially. For six years Les Fonderies et Forges. de Sainte-Maire et Gravigny and the works of Bouchayer & Viallet at Grenoble have manufactured pure-iron boiler tubes in competition with established practice. The French process originated in the researches of Anthelme Boucher in 1910, and was, not put into operation until several years of experimentation had passed.

Jan 1, 1921

By Lenin T., Madhav M. R., Padmavathi V.

Use of PVDs and preloading on the ground can significantly reduce the time taken for ground to consolidate. Many soils in situ are lightly overconsolidated, with overconsolidation ratios (OCR) ranging from 1.0 to 2.0 due to various reasons such as glaciation, ground water level fluctuation, aging, cyclic loading, creep, erosion, cementation, etc. The effects of overconsolidation ratio are analysed in this study. Compression index and consolidation coefficient are important parameters in determining time – settlement response of soft soils under preloading and with PVDs. These parameters are typically estimated using oedometer tests on samples, with the assumption that the results represent the entire deposit. The in-situ time-settlement plots at different depths are used in the back analysis for estimating compressibility and consolidation parameters of in situ ground, resulting in more representative values that reflect the deposit's overall behavior. From observed time versus settlements plots, variations of compression index and coefficient of consolidation with depth of a deposit are presented. Estimation of compression index with depth is possible based on different OCR values as shown in this study. Barron (1948), Asaoka methods are used to estimate the coefficient of consolidation with flow in the radial direction.

Sep 1, 2022

By C. M. Smith

PILOTED by Cadwallader, Evans, Jr., as chairman, the Coal Division got under way Monday morning for the first of three consecutive sessions. N. F. Patton started the ball rolling with a paper on the economics of anthracite distribution, which was ably discussed by H. J. Rose, W. S. Blauvelt, and others. Mr. Patton pointed out many incongruities in freight rates, dealers&apos; margins, and other factors which are disturbing the distribution of anthracite, one result being that trucks are hauling at least six million tons of anthracite annually, half of which is stolen. In the discussion of the papers the desirability of greater uniformity in the production and shipment of coal from month to month was urged; with larger summer price concessions as a means toward this end. "Performance Expectancy of Domestic Underfeed Stokers for Anthracite," by Allen J. Johnson, brought this important platter down to date by showing the range in capacities and efficiencies to be expected from well-made stokers, and by detailing other of their operating characteristics. One of his most interesting points is that the efficiency of domestic stokers is practically equal to that of handfiring for good installations and operations of both

Jan 1, 1935

By E. V. Bowman

This paper is intended to deal with the material handling aspects of fine coal cleaning as applied to a recently built plaint in: southern West Virginia. This plant is processing 160 tons per hour of 1/4" x.0 coal on a two shift basis. Past experience with this very friable low volatile metallurgical coal indicated that its plastometer readings, varied directly with the size and length of time elapsing between mining&apos; and ultimate consumption. Due to the mines location with, respect to its consumers, little could be done to decrease the time element. Studies indicated that the plastometer readings are considerably less in the minus 60 mesh range than that experienced in the plus 60 mesh sizes. Therefore, handling the coal in such a manner as to have the least amount of degradation became extremely important.

Jan 1, 1961

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By C. Allen, H. Zhang, L. Falk

Shock loss occurs when there is a change in the area of a drift or airflow direction. These shock losses accumulate throughout the ventilation system and will increase the mine resistance as underground development deepens or becomes more complex. Hence, shock losses should be carefully considered when establishing the resistance through a series of branches as they can be a significant contributor to the estimated mine resistance. Using computer software to simulate a ventilation system is common but applying reasonable shock loss factors in the software is not a simple or direct process. Determining shock loss values includes the consideration of historical measurements, application of factors and formulas from literature based on the geometry and complexity of junctions, and the geometry variation at different locations. For example, the shock loss at the bottom of a ventilation raise can consist of a 90° bend and a sudden area change. This paper presents an approach for estimating shock loss factors near raise junctions using computational fluid dynamics (CFD). Current and future work will also be compared with field measurements. Results from this approach are compared with software defaults as well as classical techniques in published literature and standards.

Sep 1, 2024

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014

By M. Abdollahy

In this paper, the hydrophobicity of chalcopyrite particles produced with different laboratory mills has been studied; different grinding mechanism in themills made some changes in particles shape, Image Analysis (IA) method was used to determine the shape properties of chalcopyrite particles which are ground by a laboratory ball mill, rod mill and ceramic ball mill. The shape characters are stated in terms of shape factors such as circularity, convexity, roundness and regularity factor. Hallimond tube was used to float chalcopyrite particles followed by determination of critical surface tension of particles, this parameter used as a criterion to study the wetting behavior of chalcopyrite particles. The correlation between shape properties and critical surface tension of chalcopyrite particles showed that the hydrophobicity of chalcopyrite was affected by the shape. Investigations showed that the circular, round and more convex particles that produced with ceramic ball mill had lower hydrophobicity with higher critical surface tension (?c). The results also showed that the hydrophobicity of particles ground by ball and rod mills increased with the decrease of roundness, circularity, convexity and regularity factor of particles. Keywords: chalcopyrite, particle morphology, flotation, image analysis system, micro flotation method, hydrophobicity, shape properties

Sep 1, 2012

By S. Sillitoe

In mining, as in other business and engineering enterprises, efficient operation depends upon how well and how quickly the lines of communication can function. Mines have used the telephone on and between levels for many years, but in the hoisting shaft maintenance of physical wire connections for communication with the moving cage or skip has been found, for all practical purposes, impossible. A most natural solution was, therefore, the code-bell or buzzer signal system between fixed levels, and this has been standard practice throughout the mining world for many years. However, this system has serious limitations which make it impossible to signal a cage between levels in the shaft, and it requires crude, hazardous or costly methods for signalling during daily shaft inspection. Radio signalling overcomes these difficulties, because the communication medium is never broken and the cage-tender or shaft inspector can safely signal to, and receive signals from, the hoistman at any time from any position in the shaft, whether stationary or in motion. In addition to both audible and visual code signalling, two-way telephone communication and slack cable alarm are facilities made possible in recent commercially developed equipment.

Jan 1, 1949

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024