Search Documents

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau&apos;s Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By S. K. Kawatra, R. A. Seitz

There is considerable variation in the types of coal flotation circuits in use in various parts of the world. For example, Russian plants frequently use scavenger flotation, while this is almost unheard of in the United States. The numerous circuit designs are intended to address specific problems in coal flotation, or to take advantage of the peculiarities of certain coal deposits. As a result, it can be difficult to decide which circuit is best for a given application. For this paper, coal flotation circuits were collected worldwide from many operating plants. These circuits include varying degrees of conditioning, and complexity ranging from simple rougher flotation to multi-stage split- stream processing. The design goals of each circuit are described, and the advantages and disadvantages of each are discussed. Extensive sampling campaigns were carried out in two plants with the most common types of coal flotation circuit (simple rougher, and rougher with deslimed feed). The performance of each plant was evaluated, and the benefits of more sophisticated processing in each case are described.

Jan 1, 1993

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for&apos; at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions&apos;, enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By Liu Z. C

Evans&apos; theory for chisel shaped picks is well known in the field of rock cutting technology. It has been widely accepted as a good mathematical description of how coal and other rocks break under the action of a simple wedge or chisel. Subsequently, Evans proposed a corresponding theory for pointed shaped picks. Theory along with experimental evidence from the laboratory has consistently shown that chisel picks are more efficient than pointed picks. However despite such evidence, pointed picks continue to be the preferred shape in most practical cutting applications. Evans&apos; theory for pointed picks was developed in an attempt to shed light on this apparent incongruity. The theory although predicting forces of the right order was found to be deficient in several respects. This paper examines Evans&apos; theory for pointed picks and proposes changes to it, which brings the theory much more into line with measured data. The issue of the relative efficiencies of chisel and pointed shaped picks is also examined on a theoretical basis and the apparent incongruity is Resolved.

Jan 1, 1995

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By Philip W. Holland

The U.S. Bureau of Mines has developed an improved method for determining dissolved helium in water in the concentration range of 4.0 x 10-8 to 270 X 10-8 cm3 He (STP)/cm3 H2O. The method is a modification of a previously reported method that was developed for analrzing surface and subsurface waters in geochemical survey work. Water samples are collected in SOD-cm stainless steel cylinders, and the dissolved gases in a sample are extracted into an evacuated cylinder of equal volume. After addition of 30 psig of nitrogen containing less than 2 ppb helium to the extracted gases, the resulting mixture is analyzed for helium using a helium-tuned mass spectrometer. The helium content of the water sample is determined from an empirical calibration that is established by analyzing standard solutions of helium in water. The accuracy of the method is ±7 pct for helium-in-water concentrations above 10 x 10-8 cm3 He (STP)/cm3 H2O.

Jan 1, 1989

By G. R. Doughty

It is shown that sodium can be removed very readily from molten aluminium by the use of a beta"-alumina, the more highly conducting form of beta-alumina, provided that the surface of the tube is wetted by a layer of salt. From current/time plots the theoretical amount of sodium removed has been calculated and excellent agreement obtained. The beta"-alumina tubes can be immersed directly in the Al without fracturing if they are pre-heated for a few minutes prior to immersion. According to its stability beta"-alumina should be attacked by molten Al at low Na contents, but in these experiments the salt acted as a protective layer. Magnesium chloride is a relatively cheap salt, whose Mg product can be used within a foundry. The only other product is NaCl, which can be used in-house as a flux or sent for disposal. No polluting gases are used or produced and no drosses created. The time for removal of sodium was quite short, comparable to that for chlorination

Jun 21, 1905

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By John A. Fagnant

At Elkol, Wyo., about 80 miles northeast of Ogden, Utah, the Kemmerer Coal Co. and the Utah Power and Light Co. are involved in a joint venture that will soon see 1 million tons of coal going "out by wire" to Ogden. Kemmerer, owner of a multi-seam strip mine, and the utility, now building a steam power plant adjacent to the mine site, expect to begin initial power generation by February 1963. Although capable of producing only 150,000 kw at that time, this plant is expected to be ultimately enlarged to 500,000-kw capacity which will require about 2 million tons of coal annually. The deposit consists of more than 30 seams of coal, usually varying in thickness from 2 to 40 ft, and separated by beds of sandstones and shales. In certain areas the aggregate thickness of all the coal seams measures 300 ft. The thickest and most spectacular of these seams is the lowest one, referred to as the No. 1 seam, which is 118 ft thick in some places.

Jan 8, 1962

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resur-gence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available.

Jan 1, 1937

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today&apos;s environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By S. K. Mahata, P. G. Suresh Kumar, B. B. Singh

Improvement of post tap hole practices is achievable by mechanized handling of melt during the production of Ferro Chrome, resulting in higher recovery of chromium. The paper deals with modern practices adopted in the production of ferro-chrome since past two decades. The methods and practices deal with various areas : a) Improved method of operating the tap hole by selection of right quality of refractory to maintain the life of tap hole. b) Collection of melt in different types of receptacles like refractory brick lined mild steel ladles, cast steel ladles, cast iron pans being chosen for cost effective and efficient handling. c) Separation of slag and metal, casting of metal, crushing, sizing and stock piling etc. d) Slag disposal and recovery of entrapped metal. The drive behind the above development is continuous improvement, which results in higher chromium recovery and reduces loss of metal in slag by completely mechanized method so as to be at the same level with producers of ferro-chrome in other advanced countries , in the emerging global economy.

Jan 1, 2007

By Walter J. Frank

Thls report summarizes work done under Bureau of Mines contract H0357100, "Development of a Crimp Connector for Trailing Cable Splices." The purpose of this effort was to establish optimum connector design conditions to meet flex cycle, pullout and electrical resistance criteria on phase power conductors. Field testing of "optimum design" connectors is briefly discussed. One of the primary objectives of contract H0357100 was to enable one to design better performing phase conductor connectors. Illustrating the practical significance of this 1s a discussion on the development of a new splice kit for trailing cables. The connectors in this kit were designed in accordance with the design methods described in the contract final report. Kit components, test data, and a connector installation tool are also discussed. The successful effort on the phase connector has resulted in contract H0377042, entitled "Design and Testing of Joining Sleeves for Trailing Cable Ground and Pilot Wires." The purpose of this contract (currently in effect) is to improve ground-conductor and pilot-wire performance. Significant findings to date are discussed.

Jan 1, 1979