Search Documents

By H. S. Chiang, S. S. Peng

INTRODUCTION Underground coal mining disturbs the original in-situ conditions which induces a series of strata activities and results in creating "mine pressures," the source of all ground control problems. Adoption of self advancing powered supports in modern longwall mining adds a new dimension to ground control problems and thus research. Roof stability, in general, refers to the integrity and stability of the immediate roof which is measured by the maximum exposed area and time duration without support. There are many factors that con- tribute to roof stability problems. In addition to mining height, rock property and stratum components and caving angle of the immediate roof, characteristics of joints and fissures and their degrees of development, faults and underground water, the operational techniques also play a very important role. This paper summarizes these operational techniques and methods of controlling stable and unstable roof. CLASSIFICATION OF THE IMMEDIATE ROOF There are many ways of classifying the roof (1). For practical purpose, the immediate roof in this paper is divided into three groups, i.e. unstable. medium stable and stable. Unstable Immediate Roof It has the following features (1) It consists of weak or soft carbonaceous shale, black shale, clay shale and well-jointed or fractures sandy shale

Jan 1, 1983

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Andrew Hyslop

In our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber-tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys- tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1949

By Thomas F. Torries, George H. K. Schenck

Crushed and broken stone is used directly in construction as an aggregate and accounts for about half the value and two-fifths of the quantity of natural aggregates consumed in the United States. Sand and gravel provide most of the balance of aggregates except for some lightweight materials such as pumice and expanded shale. Conditions necessary for production of crushed stone from a deposit are : 1) Quality-should pass rigid specifications for strength and durability. 2) Cost-low average total delivered cost. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass either (1) by the addition of cementing or binding materials that produce a concrete or (2) by compaction or by natural weight to produce a road base or foundation. Aggregates usually provide about 80 to 100% of the material volume of the construction masses in which they are used. The construction industry utilizes as aggregates about 70% of all crushed stone produced in the United States according to statistics provided by the U.S. Bureau of Mines (USBM) , [Table 1], using definitions as shown below. Nonconstruction uses of crushed stone, [Table 2], are included elsewhere in Industrial Minerals and Rocks because such uses require the special physical or chemical characteristics which are discussed in those chapters.

Jan 1, 1975

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By Dirk Claessens

The term ?cost? is too small when describing the destructive power of safety incidents for mining companies. Breaches in employee or environmental safety are felt way beyond the bottom-line: human life can be taken; ecosystems tarnished; the ire of peoples, media and government inflamed; significant halting of production; and high levels of legal and financial challenges. According to a recent survey of Mining executivesi, ?ensuring workforce safety? was the most important issues identified above any other, with a plurality of 31 percent, reigning above capital projects, product efficiency, and equipment reliability. We accept that safety is a most paramount issue, yet for many reasons we keep approaching the problem the same way we have in the past. We need to stop doing the same things decade over decade and try something new. New innovations are significantly changing the fundamentals of how mining companies explore, excavate, produce, refine and distribute their valuable commodities. Technologies such as visualization, analytics, location awareness, and gaming simulation are making these enterprises smarter. Now, attention turns to an area we?ve long held as integral to our business: safety. By using the same breakthrough technologies that are changing our business, we can now boldly imagine ? and credibly strive for ? a world of zero incidents.

Aug 1, 2013

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By Kenneth H. Johnston

Information and data necessary for research on improving methods of oil recovery from low-permeability reservoirs and for comparison and evaluation of performance of such reservoirs with those producing from more permeable sands were obtained. Core analyses, well logs, production tests, well stimulation techniques, primary and secondary production records, and data on two water-flood projects were examined for wells producing from the Bartlesville sand, West Avant field, Osage County, Okla. Overall recovery from the study area was generally poor with only 9.0 percent of the pore volume recovered to January 1, 1968. Larger fracture treatments (8,000 to 12,000 gal) could have resulted in an increase in primary oil recovery. Secondary recovery by water-flooding accounted for only 1.9 percent of the pore volume because of the inability to control the large volume of injection fluid that escaped from the flood patterns and the excessive volumes of water produced with the oil. Future waterflood development in other low-permeability reservoirs should include the drilling of new input wells, use of injectivity surveys to locate possible natural fracture systems, or zones of high permeability, and control of injection fluids by altering flood patterns and/or plugging of the more permeable zones.

Jan 1, 1968

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By Woodcock J. T, Sparrow G. J

Activated carbon particles obtained from a number of Australian CIP operations were examined with an optical and a scanning electron micro- scope and an electron microprobe. External surfaces, and polished sec- tions through individual particles, were examined with special reference to materials on the surface and to calcium and gold distributions. Photographs are presented of surface contamination of the particles by salts precipitated from the pulp such as calcium carbonate (calcite), calcium sulphate (gypsum), and a magnesium salt; ore minerals such as quartz, hematite, pyrite, arsenopyrite, pentlandite, and various alumino- silicates; and other substances such as grinding media and a fungus. Calcite was very abundant but the other materials were less common. Contamination in the interior of carbon particles was almost exclu- sively calcium carbonate, and extensive contamination extended to the centre of some particles. A possible mechanism for the formation of cal- cium carbonate inside the carbon particles is noted. Gold X-ray dot maps of sections through carbon particles indicated that gold was distributed throughout coconut shell carbons and that although gold was more concentrated near the outer surfaces of extruded peat carbon particles, it was also present to depths of at least 500 ¦m. The gold distribution throughout the carbon particles was similar to that rf alrit~

Jan 1, 1988

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993

By Lance R. Barron

The U.S. Bureau of Mines, in cooperation with a central Utah coal .mine operator, began a study in July 1988 into longwall gateroad designs applicable to deep, bump- prone mine conditions. Prior to the study, four adjacent longwall panels, incorporating a variety of panel entry configurations using "yielding' chain pi liars, experienced severe bumps and coal outbursts at the face and in the tailgate pillars during panel extraction, resulting in several lost-time accidents and a fatality. To quantify those factors primari1y responsible for bump occurrences during panel retreat, a field investigation was initiated to confirm the anticipated performance of a two-entry gateroad system employing a large, nonyielding chain pillar design. Hydraulic borehole pressure cells and roof-to-floor closure [convergence) measurement stations were installed to monitor gateroad abutment loading and entry closure during panel extraction. Study results indicate that very high confinement of the coal seam by strong roof and floor members existing across the entire property, in conjunction with overburden depths in excess of 1.600 feet, provides for bump-scale energy storage in not only gate pillars, but along the entire periphery of the active mining area. Insufficient gate pillar designs were also identified as possibly enhancing the occurrence of bumps in the tailgate and adjacent face areas.

Jan 1, 1990

By Andrew Hyslop

IN our never ending search for new and better ways of underground mining, we find that transportation has had its share of new ideas in the past few years. The old and still effective method of track haulage has had some competition from rubber tired cars and belt conveyors, each of which has its own safety hazards which demand close scrutiny in any safety study. The use of shuttle cars, in particular, has introduced clearance hazards caused by the absence of the more or less positive guides formed by the rails of a track sys¬tem; likewise the requirement of greater clearance tends to increase roof hazards which we all know to be great enough with the best of methods. However, the subject of transportation hazards is too broad to be covered entirely in one paper, so I will confine myself to track methods which carry the preponderance of underground tonnage. I am quite sure that to this group it is an evident fact that haulage accidents are of major importance. However, to stress the point, it may be well to look at a few figures. Safety statistics can be quite boring and often are subject to question as to mathematical accuracy because of different

Jan 1, 1948

By J. Riefenberg

U.S. Bureau of Mines (USBM) researchers are developing a personal computer-based hazard mapping system for use in underground coal mines. Hazard mapping is rapidly gaining interest as delineating areas of possible instability is becoming more complex. The development of a hazard map is based on the consensus that combined effects of local and regional stresses, roof, floor, and rib quality, geology, faulting, presence of ground water, etc., all contribute to stability of the ground. In order to demonstrate the concept, a hazard map was developed that combined stresses anticipated to occur in a multiseam setting using numerical modeling, and the newly developed Coal Mine Roof Rating (CMRR) where roof quality ratings in untested areas were modeled using geostatistical methods. Ten borescope readings from an underground mine were used to compute CMRR's for the geostatistical analysis. CMRR's for the mine ranged from 57 to 77, and are considered in the moderate to strong range. A hazard map was developed by combining the stress effects of interseam mining, scaled to weigh equally with CMRR's, and CMRR geostatistical analysis results. This hazard map demonstrates a synergistic effect between the mining-induced stress fields and the roof quality ratings, indicating, as expected, a greater hazard index in areas of high stress and lesser roof quality.

Jan 1, 1994

By John J. Henn

Two lime sinter processes for recovering alumina from clay, the double-leach process and the single-leach process, are evaluated in this Bureau of Mines report. In both processes, clay and limestone are mixed and sintered to form calcium aluminate from which alumina is extracted as sodium aluminate by leaching with a dilute solution of sodium carbonate. The pregnant liquor is desilicated, then carbonated to precipitate alumina trihydrate which is recovered and calcined to a,-alumina. The fixed capital costs for plants producing 1,000 tons per day of alumina are $85 million for the double-leach process and $86 million for the single-leach process based on a Marshall and Stevens chemical equipment index of 240.0. Because plant locations are variable with respect to the proximity of clay and limestone deposits, a nomograph is included to determine operating costs at various delivered costs of clay and limestone. For plants at which the delivered cost of clay containing 30 percent A1203 is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $81.04 and $89.87 per ton of alumina for the double-leach process and single-leach pro-cess, respectively.

Jan 1, 1969

By T. I. Arbuzova

The present work presents the original data concerning using a high pressure torsion method and a shock wave loading technique to produce compact oxide nanomaterials and investigations of the effect of severe plastic deformation on a microstructure, crystal lattice and stability of these compounds. This allowed us to compare two ways of deformation action that can be characterized as quasi-static and dynamic effect, correspondingly. Particular attention was paid to a stoichiometry and surface composition changes upon severe plastic deformations. A procedure for studying chemistry of the oxide nanomaterials by means of nuclear microanalysis and Rutherford back scattering has been worked through. For surface studies the X-ray photoelectron spectroscopy has been used. It was shown that both distortion methods permit to produce massive nano-scale oxide materials from the coarse-grained powder during a single technological cycle. Bulk nanocrystalline materials based on LaMnO3, TiOy and ZrO2:Y2O3 were obtained by the quasi-static deformation technique. Nanoscaled ceramics of CuO, Mn3O4 and LaMnO3 were produced by the dynamic deformations. The density of the nanoceramics comes to 99%. Size effects and specific imperfection of the nanoceramics obtained lead to a set of particularities of physical properties.

Jan 1, 2006

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By Philippe Monier, Frank C. Basham

"This paper outlines the scope and applications of 'COALMOD', the British Columbia Ministry of Energy, Mines and Petroleum Resources' computerized financial simulation model for coal mining developments. After a description of the computer system and language of implementation, the logic and scope of current model sub-routines are presented. This is followed by a presentation of examples on the current applications of the model to public policy evaluation, including benefit-cost analysis, fiscal analysis and evaluation of the effects of public infrastructure investments made in support of mining projects.IntroductionThis presentation has been developed in response to a number of requests from coal mining companies and various public agencies who have indicated interest in understanding our application of contemporary analytical techniques to public policy in the coal sector. In particular, the subject of this paper is an explanation of COALMOD. a mnemonic given to a computerized, mine-specific, financial simulation model which is assisting the Government of British Columbia in evaluations of new coal projects, assessment of public sector investments made in support of these projects and. more generally, measurement of the financial effects of current or proposed government policies, and factors outside immediate government control such as coal prices and transportation costs."

Jan 1, 1981

The Mount Morgan eopper-gold orebody is contained within a series of Mid-Devonian volcanics which occurs as a roof pendant within Permian granite. The ore minerals comprise pyrite, chalcopyrite, and local aggregations of magnetite and pyrrhotite. Silver-rich gold (electrum) is disseminated through the ore usually in ultrafine to sub-microscopic dimensions. Accessory minerals include marcasite, digenite, chalcocite, covellite, sphalerite, bismuthinite, molybdenite, calaverite, petzite, and cassiterite.Very minor accessories include cubanite, tetrahedrite, galena, arsenopyrite, hematiIe, goethite, and rutile. The gangue minerals are quartz, predominantly, with minor amounts of chlorite and sericite.Study of microtextures of a representative suite of specimens from Mount Morgan does not reveal any criteria indicative of metasomatic replacement but does show, in the case of pyrite, evidence strongly suggestive of annealing recrystallization. Other textures in pyrite indicate porphyroblastic growth of the iron sulphide.It is inferred that the Mount Morgan orebody is genetically related to the volcanic rocks and was later contact metamorphosed by the intrusive granite or by the series of intermediate to basic dykes that transect inmine area. On this basis the Mount Morgan orebody would be a contact metamorphosed volcanic hydrothermal deposit emplaced, according to recent studies, along a pipe-like zone of brecciation.

Jan 1, 1967