Search Documents

By Lawrence Dykers

The paper presents a generalized history of the growth and utilization of electronic data processing in a medium- size, mining-oriented company. A brief narrative outlines a corporate wide data gathering system, its hardware and application. Responsibility areas for corporate accounting, operations control, engineering, and research program development are defined. A Synopsis of programs within responsibility areas is presented along with a review of program language requirements for each of these areas. Anticipated additional uses of computers and the programs being developed for these uses are outlined. The scope and growth of an Information Systems Department within Duval Corporation is briefly discussed. Suggestions are presented which should help minimize the problems and avoid some of the pitfalls of program development for those contemplating the initiation or revision of an electronic data processing system. The importance of lucid and comprehensive program documentation is stressed.

Jan 1, 1969

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By J. S. Anderson

Size reduction models of cone and impact crushers have been developed using Whiten's generic computational structure for the description of crushers. They incorporate a laboratory single particle breakage test and the t-family of curves to describe the breakage behaviour of the feed ore. A quantitative model of 7-foot cone crushers has been developed, based on surveys of Svedala (Kobe) and Nordberg machines. Survey data on a Canica vertical shaft impact machine have been used to validate the impact crusher model. Given the crusher operating conditions, such as tonnage, feed size, set and liner condition, or rotor speed and radius, plus breakage information on the feed, the models provide good predictions of product size distribution, and appear to be robust over a wide range of conditions. They are incorporated in commercially available computer simulation packages.

Jan 1, 1998

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By Michael B. Kahle, Fred J. Scheaffer

Production scheduling, along with production planning, provides projections of future mining progress and time requirements for the development and extraction of a resource. These schedules and plans are used by management as a means of attaining the following objectives (1) maintaining or maximizing expected profit, (2) determining future investment in mining, (3) optimizing return on investment, (4) evaluating alternative Investments, and (5) conserving and developing owned resources. The first four goals are generally concerned with mining costs, both capital and operating requirements, and as such, play an important role in production planning. However, this chapter is concerned with the fifth management objective of resource development in order to conserve and perpetuate the corporate entity. The following discussion is based on the premise that detailed economic evaluations and market surveys have been performed and analyzed and that the results indi¬cate a viable project.

Jan 1, 1979

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By Pierre Labrecque

Dispatch systems have been used for open pit mining since the early 1980?s but similar systems do not widely exist for underground mining. There is a need for developing dispatch systems for underground mines, particularly highly automated operations such as block caving. An innovative method, Agent Based Modeling (ABM) for a dispatch system for a block caving operation, is proposed in this paper. The model is based on a particular behaviour observed in social insects. The focus of the ABM dispatch system is adaptability with respect to changing operational conditions and effective integration of maintenance modules with the operation. The paper will show the advantages of this innovative method compared to existing similar systems. Furthermore, the preliminary approaches for developing an agent based modeling system for block caving operations are highlighted and discussed in this paper. 1. Introduction In social

May 1, 2008

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By J. Dehais, W. A. Wallace

The pressures of urbanization are forcing producers of construction minerals either to transport their product greater distances or find new mineral sources. In areas with significant urban development near the coastal zone, offshore resources may prove to be an economically attractive alternative source. This paper addresses the economic viability of offshore mining of fine mineral aggregate. It proposes a model using a mathematical programming formulation based upon past research on both the onshore construction aggregate industry and the coal industry. The model is then used to assess offshore mining economics in the greater New York metropolitan area. Results show that in this region total consumer cost would be reduced by offshore mining of fine aggregate. In addition, increasing economies of scale could be realized by progressively larger mining operations. The distribution of these savings is also discussed.

Jan 1, 1982

By W. P. Blake

THIS furnace is designed especially for the oxidation of sulphur or arsenic in pyritic ores, but may be used for all oxidizing or desulphurizing operations, and for calcining, roasting and chloridizing ores, or for drying ores in large quantities preparatory to treatment by magnetic separators or otherwise. It is of the tabular, revolving type, with automatic feed and delivery, and is a modification of the Cornish calcining furnace, designed by Brunton, from which it differs, however, not only in construction, but in two or more radical features, for which novelty is claimed and patents have been applied for. The principal of these novelties are: 1. A series of concentric terraced floors, one above another. 2. The introduction of superheated air upon the charge without contact with the fuel. In the furnace which I have had in operation for more than a

Jan 1, 1893

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By S Williams

The primary objective of most mining projects is to maximise the value delivered to the companyÆs shareholders. Achieving best practice performance and maintaining competitive advantage through low-cost production and high productivity is essential to achieving this aim. Benchmarking is an essential tool for the identification and implementation of best practice performance, and to realise continuous improvement by ensuring best practice becomes common practice. But to be successful, that is to deliver long-term value creation, benchmarking must be holistic and align operational performance with strategic intent. This paper outlines a rigorous and structured approach on how to conduct a successful benchmarking program that aligns operational performance with the businessÆs goals. Further it investigates the benefits that benchmarking can provide throughout the project life cycle and provides some key learnings from some of the worldÆs leading miners.

Jan 1, 2009

By E. C. Herkenhoff

THIS subject may be controversial. Personal preferences influence the final selection of cyclones, and side issues such as costs, floor areas, head room, and ease of replacing worn parts all enter the picture, but the following comments and data should apply to most cyclone selection problems. Broadly, the uses for cyclones in wet classification may be divided into three fields: 1) Open circuit operation, for two products, in which feed rate and sizing vary and the products vary. For example, feed may be divided into a sand product and a slime product. 2) Open circuit operation, for two products, in which feed varies, one product to have constant sizing. This calls for adjustment in either the apex or the vortex aperture. 3) Closed circuit operation, the finished product to have constant sizing. Most classification jobs fall in this category.

Jan 8, 1957

By Gerard A. Flierman

INTRODUCTION There is a lot of discussion about the relative merits of sinter and pellets as components of a BF-burden. Many people claim that sinter is to be preferred and that the percentage of pellets in the burden must be restricted to 20%. During BF-trials in IJmuiden various amounts of pellets having various basicities were tried. It was concluded that there were no significant differences in furnace performance. Consequently the choice between sinter and pellets must be based on the local manufacturing costs (1). Table 1 gives a summary of the pellet experience in IJmuiden. [ ] Because the BF-trials were relatively short, a survey of published BF-operating data has been undertaken to investigate if differences between a sinter and pellet based BF- practice could be found. The comparison of BF-operating results has been restricted to coke rate and productivity.

Jan 1, 1977

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979

By R. R. Tatiya

The algorithms to model three stoping methods - sublevel, down- the-hole (DTH) and cut and fill stoping have been developed. These algorithms are capable of designing and performing economic analysis for one or more number of stopes in a continuous orebody. The design and economic analysis of each individual stope are first obtained. This is followed by the composite stope design layout and overall economics of the stopes under study. This paper describes only the stope design aspects of these models. The programs have been written using Fortran 77 with Tektronix graphical aids available at Imperial College Computer Centre (ICCC) London and are based on the basic data obtained from Khetri Copper Complex (KCC) and Rajpura Dariba (a zinc mine) in India. Minor modifications, however, may be necessary in some routines when used on other systems and for other mines.

Jan 1, 1989

By Peter J. Suardini

Over the last few years, researcher have been working on improving procedures for fine-coal (minus 150 microns) washability analyses. The effort was stimulated by past difficulties in obtaining accurate and reproducible results from the various commercial laboratories providing fined washability services. This paper contains the results from fine-coal washability testing, performed by Process Technology, Inc. (PTI), as part of a U.S. Department of Energy (DOE)-sponsored project. The testing focused on comparing the performance of a number of media options (i.e., aqueous solutions and organic solvents), as well as evaluating the impact of a number of procedural steps on separation performance. The paper summarizes PTI's recommended washability procedures for various size fractions and ranks of coal, and makes recommendations for future studies of certain phenomenon, such as void penetration and particle density changes, which are not well understood.

Jan 1, 1995

By E. M. Frizzell

In an effort to economically and efficiently enhance the erosion control aspects of present surface coal mine reclamation practices, the US Bureau of Mines has recently completed a two-phase research program wherein irrigation strategies and equipment developed under the first phase were field tested on three surface coal mine sites. The fundamental basis for the use of irrigation as a reclamation tool is to provide the plant moisture requirements as a supplement to prevailing natural precipitation, and thereby support the natural growth of drought-hardy native vegetation. Portable solid-set irrigation equipment and several irrigation strategies were tested on large 6-ha (15-acre) sites in Montana, Wyoming, and New Mexico. Results of these tests will be presented which include daily irrigations, precipitation levels, soil moistures, climatic data, and density cover and biomass of the native plants.

Jan 1, 1987

By R. A. Spitz, T. C. Frankiewicz, R. E. Lueders, D. S. Davies

Further development of the Nitric-Sulfuric Leach (NSL) process has led to an improved design of the leach and nitric acid recovery steps. NO produced in the leach step is reacted with oxygen, regenerating NO2, which is sparged directly into the leach reactor. Leaching is simplified to two steps, and the nitric acid plant is replaced with an oxidation recycle gas system. Laboratory work substantiated the concept and led to selection of operating conditions. The lab work also pointed to improved process control compared to use of nitric acid as the sole oxidant. Recovery of copper from purified pregnant liquor is modified to use air agitation electrowinning improving cathode quality and lowering tankhouse costs. Economic evaluation shows reduction of capital requirements from $2640 per annual ton to $2220 per annual ton in 1978 dollars for 45 kt/a of copper production.

Jan 1, 1982