Search Documents

By J. A. du Plessis, C. Dorfling

Selenium, tellurium and other precious metals (OPMs, namely Rh, Ru and Ir) dissolve in the final leaching stage of base metal refineries. Se and Te are typically removed from the copper sulphate leach solution by precipitation with sulphurous acid. Recovery of dissolved OPMs is desirable because it will reduce OPM inventory and losses. Thiourea is an effective OPM precipitation reagent, but yields insufficient Te removal. Copper is known to enhance Te precipitation when using sulphurous acid as precipitation reagent. The primary objective of this project was to evaluate whether simultaneous precipitation of Se, Te and OPMs using thiourea with metallic copper as precipitation reagents is possible. Batch precipitation tests were performed to evaluate the effect of temperature (50 – 70°C), thiourea addition (160 – 430% excess) and copper addition (2 – 8 g/L) on Se, Te and OPM precipitation. Increasing the temperature from 50°C to 70°C resulted in an average increase of 55.6 percentage points for Se precipitation and 13.5 – 23.5 percentage points for OPM precipitation. The copper addition did not have a significant impact on the precipitation behaviour. Increasing the thiourea addition increased the precipitation of Se and Te, especially when the copper addition was low; Rh and Ru precipitation also increased with up to 10 and 12 percentage points, respectively. Despite these observations, the precipitation of Se was significantly faster when no thiourea was added. It is not currently clear why thiourea appears to inhibit the Se precipitation by reaction with metallic copper. In general, Te precipitation was low (less than 30%) at the conditions investigated. Simultaneous precipitation of Se, Te and OPMs at temperatures below 80°C does not appear to be a viable option; a multiple stage operation for sequential removal of Se and Te with copper followed by OPM precipitation with thiourea would be required.

Jan 1, 2016

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By H. R. Manouchehri

Large variations in flotation characteristics of minerals have been observed in winter and summer in plant practices as a result of changes in pulp temperature. Variations in temperature may affect the quality for pulp and related process water through changes in dissociation of different chemical species within the pulp, as well as changing in gas and metal hydroxide solubility, reagent adsorption and its stability on mineral surfaces, water/pulp viscosity, etc. All of these affect the flotation characteristics of specific mineral to some degree or another. It has been observed in Cu-Pb-Zn and/or Pb-Zn sulfides flotation that sphalerite (ZnS) flotation is strongly affected by changes in pulp temperature. Plant practices have shown that at the both low, e.g., T <10-12°C, and high, e.g., T > 60°C, the recovery for copper activated sphalerite is dramatically dropped. Within this paper the effect of pulp temperature on flotation characteristics of sphalerite is brought into considerations and laboratory flotation tests were conducted in conjunction with surface and solution chemistry analysis to understand the effect of temperature on sphalerite recovery. The effect of temperature seems to be complex since the temperature affects both the physical (hydrodynamics) and chemical phenomena in the flotation cell. In fact all sub-processes in flotation, i.e., collision, attachment and detachment, are affected by changing in temperature. Experimental results indicating that at alkaline pH values, e.g., 8.5 to 10.5, the recovery for copper-activated sphalerite is dramatically reduced when temperature is below 10-12°C, which is in agreement with plant practice at Boliden?s Garpenberg plant in Sweden. However, results from other studies indicated that the zinc recovery is also considerably decreased at high pulp temperatures, i.e., 62°C and above.

Sep 1, 2012

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Grace Keller, Jay Jackson, Patrick Allen, Scott Lakes

Dam construction and remediation projects generate vast quantities of data. All information must be meticulously tracked, analyzed, catalogued, and submitted to the proper stakeholders to ensure safe construction, compliance with design intent, and efficient execution of the work. Traditional data collection involves hundreds or even thousands of hand-written records and checklists, which must be deciphered and manually digitized to verify work outcomes. This process is time-consuming and leaves much room for error. To maximize quality and efficiency while minimizing errors, we deployed a robust Data Management Program. By utilizing digital tools and cloud-based automation, we optimized the Quality Assurance program on the Gross Reservoir Expansion (GRE) Project. The GRE project is a large-scale dam raise located near Denver, Colorado, designed to increase the capacity of Gross Reservoir by raising the existing dam 131 ft using Roller Compacted Concrete (RCC). Given the complex nature of the project, extensive data management and post-processing were required to ensure quality construction. We eliminated the need for paper records by implementing source-to-source data collection. Contractor data was exported in raw form and automatically collected via cloud-based automation. We also built customized mobile applications for inspections, which sends checklist results directly to a cloud database. Data visualization occurs in real-time, and interactive dashboards track status and automatically reflect the updated database, allowing stakeholders to interact with the data to gain insights. Document generation and distribution were also automated, streamlining reporting and filing processes and directly impacting regulatory site audits. This paper will expand on these tools and solutions to provide greater insight on their purpose, use, and execution and illustrate the benefits of an efficient data management program on large-scale dam projects.

Oct 7, 2024

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

By F F. Pitard

The optimisation of a metallurgical plant requires two kinds of sampling systems. The first provides samples to follow process changes, so in due time actions to maintain key parameters within pre-established specifications can be applied. The second provides composite samples at the end of a working shift to demonstrate that valuable constituents sent to the plant went to either a final concentrate or to the tailings in a logical, expected proportion. Contrary to what many experts may claim, these two kinds of sampling requirements are incompatible and cannot be fulfilled using the same sampling systems; this is because the required samples have completely different objectives. A process control sample is an instantaneous sample with increments taken at short intervals, and the objective is to know where the process is at any given time. Excellent accuracy is not a must, however good precision is recommended since a possible process correction may need to be made. Online analysers fed with in-stream stationary cutters or other kinds of in-stream or by-stream probes can do well for such a mission. A composite sample for metallurgical accounting with increments collected over a long period of time, for which excellent accuracy and good precision are both required, must be generated by sophisticated and extremely well-maintained cross-stream sampling stations. The use of process control sampling systems to achieve good metallurgical accounting has been promoted by several manufacturers of sampling equipment around the world; it is a grave mistake that is misleading top management and a practice that should be scrutinised and preferably eliminated. Furthermore, bias tests used to prove otherwise are often based on insufficient data to draw valid conclusions; a guideline is provided.CITATION:Pitard, F F, 2014. Sampling systems for process control and metallurgical accounting, in Proceedings Sampling 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Chris Plackowski, Bruckard. Warren J., Anh V. Nguyen

"Enargite is a significant penalty mineral in the copper industry and its separation from many copper sulfides by flotation is difficult. The separation may be crudely achieved using selective oxidation techniques or through the use of pulp potential control. This paper summarizes our latest contributions to a better understanding of enargite surface electrochemistry and hydrophobicity. Oxidation, roughness, hydrophobicity and species formation on the surface of natural enargite were examined by a novel experimental approach that combines electrochemical techniques, atomic force microscopy, X-ray photoelectron spectroscopy and droplet evaporation tensiometry. It allows for synchronized electrochemical control and examination of the oxidative surface morphology, speciation and hydrophobicity of enargite at pH 4 and pH 10. At low pH, surface layer formations consisting of metal deficient sulfide and elemental sulfur were identified associated with a limited increase in roughness and heterogeneous distribution of surface species produced by initial rapid dissolution of Cu, followed by diffusion limited surface layer deposition. At high pH, a similar diffusive mechanism associated with oxidation products consisting of copper sulfate and hydroxide and a significant increase in surface roughness were established. Receding contact angle measurements showed no significant difference in the contact angle on a surface oxidized at pH 10 and the freshly polished surface. Contact angle increased from 46° on the polished surface to 59° after oxidation at pH 4. Competing effects of hydrophilic copper oxides and hydroxides, and hydrophobic species of elemental sulfur on the mineral surfaces under oxidizing conditions at pH 4, and the change in surface roughness at pH 10, contribute to the changes in enargite hydrophobicity under electrochemically-controlled oxidation conditions. Most likely, both surface species and surface roughness produced by oxidation are critical to the changes in the wettability of enargite and other sulfide minerals."

Jan 1, 2014

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By T O&apos, Sullivan

Reconciliation of metal production from a sublevel cave (SLC) mining operation is a complicated process. SLC reconciliation is unlike reconciliation for open stope operations, where a tonnage of extracted ore can be assigned to an exact volume of in situ ore, and a direct comparison made between the estimation of contained metal and actual metal production. In SLC operations the ore extracted from a particular SLC drawpoint will be composed in part from the parcel of freshly blasted in situ material, in part from varying components of ore material (from cave stocks) flowing down from other previously mined areas vertically above the current draw position and in part from external dilution. This leads to difficulties in reconciling production grades against estimated grades. The problem is that we know how much metal we have produced but we can not precisely say where it has come from. Metal production reconciliation is fundamental in assessing ore reserve estimation accuracy and performance and in determining a draw management strategy for SLC mining. In terms of contained metal, differences in extracted metal compared to in situ metal represent changes to cave stocks. To generate local estimates of the cave stocks, differences in metal for each ring are treated as additions to or subtractions from a series of vertical columns of stocks extending throughout the height of the cave. The sum of metal differences (extracted versus in situ) for each vertical column results in a residual metal map at any particular mining level. The metal maps show areas where the metal production has been greater than or less than expected. The maps also highlight areas in the cave where residual metal is located, areas where targeted overdraw can reduce cave stocks.

Jan 1, 2006

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo&apos;s energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By D. T. Smith, L. M. Hsiung, J. J. Schmitt, J. W. Golz, R. L. Lankey, H. N. G. Wadley, J. Z. Zhang, B. L. Halpern

"The microstructure and mechanical properties of Al/AI2O 3 metal-oxide nanolaminates fabricated by' a novel Jet Vapor Deposition (JVD) process at substrate temperatures of ~25° and -250°C have been investigated using transmission electron microscopy (TEM) and nanoindentation methods. The thickness of the oxide layer was held constant between 2 and 5 nm, whilst the Al layer thickness was systematically varied from -3 to -50 nm. Continuity of the Al layers was significantly improved when the nanolaminates were deposited at an elevated substrate temperature (-250°C). The yield strength of the nanolamintes with Al layers greater than -25 nm follows a Hall-Petch type relationship, whereas that of the nanolaminates with Al layers less than -25 nm is better predicted by a Koehler-Lehoczky strengthening model. IntroductionAluminum-aluminum oxide (presumably A12O3) nanolaminates have been recently fabricated using a novel Jet Vapor Deposition (ND) process developed and patented by Jet Process Corporation [1-4]. ND uses sonic, high purity helium (He) gas jets to entrain atomically dispersed vapor and deposit films. It is of interest here because it can deposit multilayered structures (laminates) inexpensively at high rates. Materials with a thin, multilayer structure are of interest because they potentially offer novel mechanical and physical properties [5]. Koehler in 1970 used an image force model to investigate the strength of laminated materials and proposed the use of alternating layers of high and low shear modulus metals to produce high strength composite materials [6]. He predicted that dislocations would have to overcome a large repulsive image force in order to move from metal layer B of lower shear modulus (uB) into metal layer A of higher shear modulus (uA)' The image force (F) is given by the relation:"

Jan 1, 1994

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013