Search Documents

By V. E. Homme

Low- and high-temperature reduction techniques were employed by the Bureau of Mines in study of conditions favorable to the formation of massive titanium crystals. '1,1,2 low-temperature method, feeding molten sodium to solidified titanium lower chloride-sodium chloride, produced higher quality and high quantity crystalline metal. The percentage of crystalline titanium was increased with increasing reactor diameter, melt depth, and titanium dichloride concentration. The high-temperature technique, feed molten sodium to melts above 8000 C, producing needle-type crystals of lower quality and with less consistent results than the low-temperature method. Layers of titanium foil, sponge, fine needles, wool, and crusts of sin-tered granules were formed during the earl, -art of the low-temperature reduction, and massive crystals were produced beneath this barrier in the latter part of the reduction. Crystalline titanium having an average hardness of Bhn 76 and representing 58 percent of the total titanium was obtained. Lamellar crystals up to 1 1/2 inches long with a hardness as low as Bhn 54 were also produced. A second-stage reduction for reclaiming titanium from offgrade sponge is described. Titanium produced by this method was comparable in quality to that from sodium reduction of titanium tetrachloride.

Jan 1, 1966

By Thomas S. Jones

This report discusses processing and use of the principal forms of manganese. The focus is on trends in the United States in the 20th century and specifics of domestic manganese material flows as of about 1990. To protect proprietary data, quantitative assessments are limited to the iron and steel industry, which accounts for about 90% of consumption. Nonmetallurgical uses are considered qualitatively. Approximate disposition of a U.S. cumulative consumption during 1901-90 of an estimated 69 million st of manganese is estimated to be iron and steel slag, 69%; nonmetallurgical uses of a dissipative na¬ture, 10%; iron and steel scrap, 9%; National Defense Stockpile, 3%; unidentified and/or including items in service, 10%. In slag from iron blast furnaces and steelmaking, manganese is present as a minor, relatively im¬mobile component, which so far has been uneconomical to recover. Construction and road building are main applications for these slags. Steel slag contains the greater amount of manganese. Studies by others of global manganese fluxes and the effect of human activities on them also are discussed. One source concludes that the main effect of human activities, via deforestation and agricultural activities, has been to increase the rate of transport of manganese to the oceans.

Jan 1, 1994

By T. L. Turner, Daniel T. Rogers

As part of a program to investigate technology for the extraction of studied HNO3 alumina from abundant domestic ores , the Bureau of Mines leaching of calcined Georgia kaolinitic clay . In this investigation , iron impurities were removed from the aluminum nitrate pregnant leach liquor by solvent extraction , and the purified liquor was evaporated to prepare a suitably concentrated crystallizer feed liquor . Aluminum nitrate nonahydrate was crystallized from the liquor to separate the aluminum from undesirable trace elements and excess water . Continuous crystallization at 40 ° C in a pilot plant vacuum evaporative unit was performed for 5 days to observe the effects of impurity buildup under minimum bleed- stream conditions . Liquor feed rate was 26 lb/h and AAll (( NNOO33 )) 33..99HH22O0 ((AANNNN)) crystal production rate was 17 lb/h . Fe 203 and Cr203 were not effectively separated from the crystals , and P205 , MgO , and K20 impurities must be removed by recrystallization . Other impurities did not excessively contaminate the crystals . Washing the crystals with water or aqueous HNO3 gave an equivalent increase in crystal purity levels by displacing mother liquor . Theoretical equations , applicable to any continuous evaporative crystallization of developed to produce material balances for engineering ANN , were applications .

Jan 1, 1965

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Nasib Al Habib, Hooman Askari-Nasab, EUGENE BEN-AWUAH

In-pit crushing and conveying (IPCC) is getting popular in deeper open pit mines as a suitable alternative to truck haulage because it offers a lower operating cost due to shorter haulage distance and less truck requirement. Semi-mobile in-pit crusher, currently the most popular IPCC system, is relocated every two to five years, and the short-term plan needs to be updated accordingly. To the best of our knowledge, short-term planning with IPCC is an area of research that has yet to be explored extensively, and hardly any model can generate a shortterm extraction sequence considering an IPCC. This research work proposes a mixed integer programming model to develop a short-term production plan within a time horizon of 12 months. The model's objective is to optimally allocate shovels to minimize the cost of material handling and maximize revenue subject to meeting plant requirements, maximum allowable tonnage variation and IPCC location constraints to achieve production and NPV targets set by the strategic plan. The proposed model will be implemented in an iron ore mine case study for verification. The model is developed and solved using MATLAB. The comparison of results between scenarios with and without IPCC justifies the use of IPCC in large open pit mines from a short-term perspective.

Jun 25, 2023

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of manganese from known domestic occurrences. Eight of these deposits were found to have demonstrated resources totaling 420 million metric tons with an average grade of 10 percent contained manganese. They were found to be submarginally subeconomic. Economic evaluations of the eight deposits resulted in incentive prices ranging from $8 to almost $35 per long ton unit (22.4 pounds) of contained manganese. Comparing these prices with the current market value of $1.70 per long ton unit of manganese clearly illustrates the submarginal nature of the domestic ores analyzed. These domestic resources would probably not be developed except in the case of an extreme national emergency. Production from the eight deposits would take 3 to 6 years to develop, and the final product would be manganese ore concentrate, which could be used in the production of ferromanganese. If preproduction development began in 1981, annual production would peak in 1987 with 900,000 metric tons of recoverable manganese. Thereafter, production would see a steady decline unless additional resources were located or technologic improvements were made to allow processing of lower grade material, or unless mining and processing of ocean manganese nodules began to take place.

Jan 1, 1982

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By C. F. Gleeson

"Geochemical stream-sediment reconnaissance can be a useful exploration tool from the point of view of rapidly and cheaply evaluating the mineral potential of an area. This is particularly true of rugged and mountainous areas such as are found in Gaspé. For the past two years, SOQUEM has been carrying out such surveys over favorable geological regions in the Appalachians of northern New Brunswick and Gaspe. To date, about 4,000 square miles of terrain has been systematically covered by reconnaissance geochemistry. Jeeps have been used as a means of transportation in the easily accessible areas and a helicopter equipped with a winch has been used to lower crews into the more difficult-to-reach regions. Such surveys have been successful in finding metallic mineralization which otherwise might not have been detected.Electronic computation of analytical information has been used to construct regional metal maps, rolling mean maps and residual metal maps. These maps have helped in evaluating anomalies, in relating the regional geo-chemistry to the regional geology and in comparing the distribution patterns of metals. To date, some 30,000 stream-sediment samples have been collected from the Gaspe region and analyzed for Cu, Pb, Zn and Mn. These analyses are being subjected to computer analysis."

Jan 1, 1969

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By K. E. Hjelmstad

During an underground mine fire, air can be rapidly depleted of oxygen and contaminated with smoke and toxic fire gases. Any delay in warning miners could have disastrous consequences. Unfortunately, present mine fire alarm systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in mine area coverage. Recent research by the U.S. Bureau of Mines has demonstrated that ultra low frequency electromagnetic signaling can be used for an underground mine fire alarm. In field tests of prototype equipment at five mines, electromagnetic signals from 630 to 2,000 Hz were transmitted through mine rock for distances as great as 1,645 m to an intrinsically safe receiver. The prototype system uses off-the-shelf components and state-of-the-art technology to insure high reliability and low cost. When utilized, this. technology would enable simultaneous and instantaneous warning of all underground personnel, regardless of their location or work activity, thereby increasing the likelihood of their successfully escaping a mine disaster. This report presents the theoretical basis for through-the-rock ultra low frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 2010

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By Marcia L. Harris

Toxic fumes produced by detonating explosives in surface mining and construction operations pose potential hazards to workers and the public. Blasting operations produce both toxic and nontoxic gaseous products; the toxic products are mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings as well as one fatality. At worst people may be fatally poisoned and the least to be expected is increased public objections to blasting. Local and state agencies could demand a cessation of the blasting requiring more expensive mechanical means to break the rock. This paper discusses the most feasible means of preventing CO migration, mitigating CO that has migrated, and detecting CO in an underground enclosed space and may help reduce the exposure of unsuspecting area residents to carbon monoxide and help prevent the implementation of unnecessary regulations and limitations on blasting. Single-hole shots and small-scale multiple-hole blasts were performed that indicate promising means of prevention and mitigation.

Jan 1, 2008

By Richard A. Thomas, Connor B. Brown, Thomas H. Dubaniewicz, Teresa Barone

Electric vehicles powered by lithium-ion (Li-ion) batteries are being developed by mining vehicle manufacturers as a replacement for diesel-powered vehicles. Explosion-proof (XP) enclosures are frequently employed to enclose electrical ignition sources in gaseous underground mines to prevent the spread of an internal methane-air explosion to a nearby explosive atmosphere. Due to thermal runaway (TR), Li-ion batteries have the potential to cause pressurized explosions in an enclosed structure. Past research has shown the potential for well-confined Li-ion cell TR to drive pressures beyond the conventional pressure specification for XP enclosures. Researchers at the National Institute for Occupational Safety and Health (NIOSH) used an Accelerating Rate Calorimeter (ARC) to induce thermal runaway of Lithium Titanate or Lithium Titanium Oxide (LTO) type 18650 cells enclosed within containers with various volumes and found an inverse power relationship between the TR pressure and available free space. The results were similar in magnitude to that of lithium iron phosphate (LFP) cells, which were used in prior testing. Temperatures, gas amounts, and TR pressure-rise rates were also recorded. The data indicate that with enough free space, the pressures can be lowered below the conventional pressure specification for XP enclosures.

Feb 1, 2024

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By Theophilus Mensah, Kwame Awuah-Offei

Engineers face significant challenges when determining what geometry provides the most profitable and safe stope for extraction. Several techniques and optimization algorithms have been developed in recent years, but most fail to find optimal solutions because they are heuristic or LP-based without efficient geometric constraints. This paper presents a two-dimensional binary linear programming (BLP) model for determining the optimal combination of blocks in a stope that maximizes the economic value of the layout of stopes for a sublevel deposit. The work draws from Queyranne and Wolsey’s (2017 & 2018) formulations of tight constraints for bounded up/down times in production planning problems to formulate novel and efficient geometric constraints along with geotechnical and grade constraints for the BLP stope layout optimization problem. Results from the model indicate that it is possible to formulate efficient shape constraints in LP-based approaches. The model used for the numerical example contained 144 valuable blocks out of 774 blocks, which translates into an economic value of $53.21M. The BLP model selected 60 valuable blocks and 13 waste blocks that met all constraints translating into a maximum economic value of $34.4M in 1.83 hours within a gap tolerance of 0.00%.

Jun 25, 2023